Micro Motion Power Supply Owner's manual

Micro Motion
Brand
Micro Motion
Model
Power Supply
Type
Owner's manual

Micro Motion Power Supply

The Micro Motion Power Supply is a reliable and accurate power supply for the D600 sensor. It is designed to provide the correct voltage and current to the sensor, ensuring optimal performance. The power supply is also protected against overvoltage and short circuits, making it a safe and reliable choice for your application.

The Micro Motion Power Supply features:

  • Voltage regulation to ensure a consistent voltage supply to the sensor
  • Current limiting to protect the sensor from damage
  • Overvoltage protection to protect the sensor from damage
  • Short circuit protection to protect the sensor and power supply from damage

Micro Motion Power Supply

The Micro Motion Power Supply is a reliable and accurate power supply for the D600 sensor. It is designed to provide the correct voltage and current to the sensor, ensuring optimal performance. The power supply is also protected against overvoltage and short circuits, making it a safe and reliable choice for your application.

The Micro Motion Power Supply features:

  • Voltage regulation to ensure a consistent voltage supply to the sensor
  • Current limiting to protect the sensor from damage
  • Overvoltage protection to protect the sensor from damage
  • Short circuit protection to protect the sensor and power supply from damage
recycled paper
Micro Motion Inc. USA
7070 Winchester Circle
Boulder, Colorado 80301
Tel (303) 530-8400
(800) 522-6277
Fax (303) 530-8459
Visit us on the Internet at www.micromotion.com
Micro Motion Europe
Groeneveldselaan 6
3903 AZ Veenendaal
The Netherlands
Tel +31 (0) 318 549 549
Fax +31 (0) 318 549 559
Micro Motion Asia
1 Pandan Crescent
Singapore 128461
Republic of Singapore
Tel (65) 777-8211
Fax (65) 770-8003
Power-Supply Wiring for the D600 Sensor
• Micro Motion D600 sensors comply with EMC directive
89/336/EEC and low-voltage directive 73/23/EEC, when
properly installed in accordance with these instructions.
• Terminal 1 is line, terminal 2 is neutral, and terminal 3 is
ground. See
Figure 1
.
• Ground the sensor with a maximum impedance of 1 ohm.
Connect and bond a user-supplied ground wire to the earth
ground connection on the amplifier housing. See
Figure 1
.
• A switch may be installed in the power-supply line. For
compliance with low-voltage directive 73/23/EEC, a switch
is required.
• Do not install power-supply wiring in the same cable tray or
conduit as flowmeter cable.
• If conduit is used, connect a ½-inch NPT male conduit
connector to the conduit opening in the seal for power-
supply wiring. See
Figure 1
.
• If conduit is not used, connect a ½-inch NPT male cable
gland to the conduit opening in the seal for power-supply
wiring. See
Figure 1
.
•
To install flowmeter cable
, see the cable preparation
instructions that are shipped with the cable preparation kit.
Figure 1. D600 power-supply terminals
CAUTION
Improper installation of wiring could cause
measurement error or sensor failure.
• Shut off power before installing power-supply wiring.
• For personal and system safety, follow all instructions to
ensure sensor will operate correctly.
• Match power-supply voltage with voltage indicated on
the label inside the amplifier housing.
CAUTION
Failure to seal amplifier housing could cause a short
circuit, which would result in measurement error or
flowmeter failure.
To avoid risk of condensation or excessive moisture
entering the amplifier housing:
• Seal all conduit openings.
• Install drip legs in cable or conduit.
• Fully tighten amplifier housing cover.
Install drip leg in
cable or conduit
Power-supply voltage
must match voltage
indicated on label
• Terminal 1 is line
• Terminal 2 is neutral
• Terminal 3 is ground
Earth
ground
115 V L N 5 A fuse
230 V L1 L2 3 A fuse
©1997, Micro Motion, Inc.
All rights reserved
P/N 1004381, Rev. B (1/97)
  • Page 1 1

Micro Motion Power Supply Owner's manual

Micro Motion
Brand
Micro Motion
Model
Power Supply
Type
Owner's manual

Micro Motion Power Supply

The Micro Motion Power Supply is a reliable and accurate power supply for the D600 sensor. It is designed to provide the correct voltage and current to the sensor, ensuring optimal performance. The power supply is also protected against overvoltage and short circuits, making it a safe and reliable choice for your application.

The Micro Motion Power Supply features:

  • Voltage regulation to ensure a consistent voltage supply to the sensor
  • Current limiting to protect the sensor from damage
  • Overvoltage protection to protect the sensor from damage
  • Short circuit protection to protect the sensor and power supply from damage
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents