Vulcan Hart 48RRG Datasheet

Category
Cookers
Type
Datasheet

This manual is also suitable for

GRIDDLES & BROILERS
P.O. Box 696
Louisville, KY 40201
Toll-free: 1-800-814-2028
Local: 502-778-2791
Quote & Order Fax: 1-800-444-0602
a division of ITW Food Equipment Group LLC
F-36979 (06/10)
RRG SERIES
HEAVY DUTY GAS GRIDDLES
24RRG 24" w x 24" d griddle plate
36RRG 36" w x 24" d griddle plate
48RRG 48" w x 24" d griddle plate
60RRG 60" w x 24" d griddle plate
STANDARD FEATURES
Stainless steel front, sides and 4" front top ledge.
Fully welded stainless and aluminized steel chassis frame.
11" low prole cooking height on 4" adjustable legs.
3
4
" composite griddle plate with stainless steel cooking
surface.
Top and bottom plate seam welded.
4" backsplash with tapered side splashes.
One 27,500 BTU/hr. “U” shaped burner for every 12" of
griddle width.
One solid state thermostat with embedded thermocouple
for each burner.
Thermostat knob guards
Temperature adjust from 150° to 450° F.
Electronic ignition with pilot safety system.
3
1
2
" wide stainless steel front grease trough.
Large capacity 6
7
8
" wide x 30" deep x 2
1
2
" high stainless
steel grease drawer.
3
4
" rear gas connection and gas pressure regulator.
120V 50/60Hz 1 Amp single phase with NEMA 5-15 USA
plug.
36RRG, 48RRG and 60RRG models are Energy Star rated.
One year limited parts and labor warranty.
OPTIONS
Leg lengths 4", 5
5
8
", 8", 10", 11
3
4
"
Stainless steel stand with marine edges and casters.
Stainless steel, hinged thermostat cover with magnetic
latch.
Cutting board, condiment rail, plate rail and towel bar
accessories.
SPECIFICATIONS
Low prole heavy duty gas griddle, Vulcan-Hart Model No.
__________. Stainless steel front, sides and front top ledge.
Fully welded stainless and aluminized steel chassis frame. 11"
low prole cooking height on 4" legs.
3
4
" composite griddle
plate with stainless steel cooking surface welded to stainless
steel back and tapered side splashes. One 27,500 BTU/hr. “U
shaped aluminized steel burner and solid state thermostat for
each 12" of griddle width. Temperature adjusts from 150° to
450°. Electronic ignition with pilot safety system. 3
1
2
" wide
stainless steel front grease trough. 120V 50/60Hz 1 amp single
phase with NEMA 5-15 USA plug. Large capacity 6
7
8
" wide
x 30" deep x 2
1
2
" high stainless steel grease drawer.
3
4
" rear
gas connection and gas pressure regulator.
SPECIFY TYPE OF GAS WHEN ORDERING.
SPECIFY ALTITUDE WHEN ABOVE 3,999 FT.
Model 48RRG
P.O. Box 696
Louisville, KY 40201
Toll-free: 1-800-814-2028
Local: 502-778-2791
Quote & Order Fax: 1-800-444-0602
a division of ITW Food Equipment Group LLC
GRIDDLES & BROILERS
F-36979 (06/10)
RRG SERIES
HEAVY DUTY GAS GRIDDLES
NOTE: In line with its policy to continually improve its products, Vulcan reserves the right to change materials and specications without notice.
MODEL WIDTH DEPTH
OVERALL
HEIGHT*
WORKING
HEIGHT*
NO. OF
BURNERS
TOTAL
BTU/HR.
NO. OF
DRAWERS
APPROX.
SHIP. WT.
24RRG 24" 33" 15
1
2
" 11
3
8
" 2 55,000 1 200 lbs./91 kg.
36RRG 36" 33" 15
1
2
" 11
3
8
" 3 82,500 1 255 lbs./116 kg.
48RRG 48" 33" 15
1
2
" 11
3
8
" 4 110,000 1 320 lbs./145 kg.
60RRG 60" 33" 15
1
2
" 11
3
8
" 5 137, 50 0 2 380 lbs./172 kg.
*These are nominal dimensions and can vary by +1.75" with adjustable legs.
**All rear grease option griddles have only one (1) grease drawer on the left side.
INSTALLATION INSTRUCTIONS
1. A gas pressure regulator supplied with the unit must be installed;
Natural Gas 5.0" (127 mm) W.C.
Propane Gas 10.0" (254 mm) W.C.
2. All models require a 6" (152 mm) clearance at both sides and
rear adjacent to combustible and 0" from non-combustible
constructions. All models require a 4" (102mm) bottom clearance
and must be installed with minimum 4" legs.
3. These units are manufactured for installation in accordance with
ANSI/NFPA-70, National Electrical code.
An adequate ventilation system is required for Commercial
Cooking Equipment (NFPA No. 96). Information may be
obtained by writing to the National Fire Protection Association,
Batterymarch Park, Quincy, MA 02169.
4. These units are manufactured for installation in accordance with
National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition).
Copies may be obtained from The American Gas Association,
Accredited Standards Committee Z223 @ 400 N. Capital St. NW,
Washington, DC 20001, or the Secretary Standards Council,
NFPA, 1 Batterymarch Park, Quincy, MA 02169-7471.
NOTE: In The Commonwealth of Massachusetts
All gas appliances vented through ventilation hood or exhaust
system equipped with a damper or with a power means of exhaust
shall comply with 248 CMR.
5. This appliance is manufactured for commercial installation only
and is not intended for home use.
FRONT VIEW SIDE VIEW
  • Page 1 1
  • Page 2 2

Vulcan Hart 48RRG Datasheet

Category
Cookers
Type
Datasheet
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI