Dell PowerVault MD3200 Series Quick start guide

Dell PowerVault MD3200 and

MD3220 Storage Arrays

Getting Started

With Your System

Začínáme se systémem

Mise en route

Handbuch zum Einstieg

Τα πρώτα βήματα με το σύστημά σας

Rozpoczęcie pracy z systemem

Начало работы с системой

Introducción al sistema

Sisteminizi Kullanmaya Başlarken

Page is loading ...

Dell PowerVault MD3200 and

MD3220 Storage Arrays

Getting Started

With Your System

Regulatory Model Series E03J and E04J

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use

of your computer.

CAUTION:

A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING:

A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerVault™ are trademarks of Dell Inc.

Microsoft

®

and Windows Server

®

are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise Linux

®

are

registered trademarks of Red Hat, Inc. in the United States and other countries. SUSE

®

is a registered

trademark of Novell, Inc. in the United States and other countries. VMware

®

is a registered trademark

of VMware, Inc. in the United States and/or other jurisdictions.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model Series E03J and E04J

2011 - 08 P/N D76VD Rev. A02

Getting Started With Your System

3

Before You Begin

NOTE:

Throughout the document, Dell PowerVault MD3200 series storage array

refers to both Dell PowerVault MD3200 and Dell PowerVault MD3220. Dell

PowerVault MD1200 series expansion enclosure refers to both Dell PowerVault

MD1200 and Dell PowerVault MD1220.

Before setting up your Dell PowerVault MD3200 series storage array, you must

consider certain best practices to ensure that your storage array operates at

maximum efficiency and offers full redundancy (if required).

• Throughout the network, always use a Category 5e (or higher)

Ethernet cable.

• Before connecting any cables between the host server and storage array,

physically label each port and connector.

• Always follow proper power-up and power-down procedures when cycling

power across the network. You must also ensure that critical network

components are on separate power circuits.

Other Documentation and Media You May Need

WARNING:

See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document or

as a separate document.

NOTE:

All PowerVault MD3200 series documents are available at

support.dell.com/manuals.

• The rack documentation included with your rack solution describes how to

install your system into a rack.

• The

Owner’s Manual

provides information about system features and

describes how to troubleshoot the system and install or replace system

components.

• The

Deployment Guide

provides information about installing and

configuring the software and hardware.

• The

CLI Guide

provides information about using the command line

interface (CLI) to configure and manage your storage array.

4

Getting Started With Your System

•The

SMI-S Programmer’s Guide

provides information about using the

SMI-S provider and SMI-S programming.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, including those

pertaining to the operating system, system management software,

system updates, and system components that you purchased

with your system.

NOTE:

Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Supported Operating Systems

• Microsoft Windows Server

• Red Hat Enterprise Linux

• SUSE Linux Enterprise Server

• VMware

NOTE:

For the latest information on all the supported operating system versions,

see the Support Matrix at support.dell.com/manuals.

Getting Started With Your System

5

Common Configurations

Cabling Your Direct-Attached Hosts

Server 1 Server 2

Corporate, public,

or private network

Server 3 Server 4

PowerVault MD3200

series storage array

6

Getting Started With Your System

Installation and Configuration

WARNING:

Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item with the packing list that shipped

with your system.

Installing the Rails and System in a Rack

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

NOTE:

To balance the weight load, it is recommended that you install the

PowerVault MD3200 series storage array at the bottom of the rack and the

PowerVault MD1200 series expansion enclosures above it.

Getting Started With Your System

7

Connecting the Power Cable(s)

Ensure that the power switch is in the OFF position before connecting the

power cables. Connect the system’s power cable(s) to the system.

Securing the Power Cable(s)

Secure the cable(s) firmly to the bracket using the provided strap.

Plug the other end of the power cables into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply (UPS) or

a power distribution unit (PDU). Each power supply must be connected

to a separate power circuit.

8

Getting Started With Your System

Cabling Your Expansion Enclosure

Turning On the Enclosure

Turn on the components in the following order:

1

PowerVault MD1200 series expansion enclosures (if used)

NOTE:

Before turning on the storage array, ensure that the expansion

enclosure status LED is blue.

PowerVault MD3200

series storage array

PowerVault MD1200

series expansion

enclosure 1 (optional)

PowerVault MD1200

series expansion

enclosure 2 (optional)

Getting Started With Your System

9

2

PowerVault MD3200 series

storage array

NOTE:

Before turning on the host server(s), ensure that the storage array

status LED is blue.

3

Host server(s)

Installing the Bezel

Install the bezel (optional).

Installing the MD Storage Software

NOTE:

For detailed instructions about installing the MD storage software, setting

up the enclosure, and the post-installation tasks, see the Deployment Guide.

The MD Storage Manager application configures, manages, and monitors the

storage array. To install the MD storage software:

1

Insert the MD series resource media.

Depending on your operating system, the installer may launch

automatically. If the installer does not launch automatically, navigate to

the root directory of the installation media (or downloaded installer

image) and run the

md_launcher.exe

file. For Linux-based systems,

navigate to the root of the resource media and run the

autorun

file.

NOTE:

By default, the Red Hat Enterprise Linux operating system mounts the

resource media with the -noexec mount option which does not allow you to

run executable files. To change this setting, see the Readme file in the root

directory of the installation media.

10

Getting Started With Your System

2

Select

Install MD Storage Software

.

3

Read and accept the license agreement.

4

Select one of the following installation options from the

Install Set

drop-down menu:

•

Full (recommended)

—Installs the MD Storage Manager (client)

software, host-based storage agent, multipath driver, and hardware

providers.

•

Host Only

—Installs the host-based storage agent and multipath

drivers.

•

Management

—Installs the management software and hardware

providers.

•

Custom

—Allows you to select specific components.

5

Select the MD storage array model(s) you are setting up to serve as data

storage for this host server.

6

Choose whether to start the event monitor service automatically when the

host server reboots or manually

NOTE:

This option is applicable only to Windows client software installation.

7

Confirm the installation location and click

Install

.

8

If prompted, reboot the host server once the installation completes.

9

Start the

MD Storage Manager

and discover the array(s).

10

If applicable, activate any premium features purchased with your storage

array. If you purchased premium features, see the printed activation card

shipped with your storage array.

NOTE:

The MD Storage Manager installer automatically installs the required

drivers, firmware, and operating system patches/hotfixes to operate your storage

array. These drivers and firmware are also available at support.dell.com. In

addition, see the Support Matrix at support.dell.com/manuals for any additional

settings and/or software required for your specific storage array.

Getting Started With Your System

11

Locating Your Service Tag

Your system is identified by a unique Express Service Code and Service Tag

number. The Express Service Code and Service Tag are found on the front

of the system and at the back of the system next to the RAID controller

modules. This information is used by Dell to route support calls to the

appropriate personnel.

NOM Information (Mexico Only)

The following information is provided on the device described

in this document in compliance with the requirements of the

official Mexican standards (NOM):

Importer:

Model number: E03J and E04J

Supply voltage: 100–240 V CA

Frequency: 50/60 Hz

Current consumption: 8.6 A

12

Getting Started With Your System

Technical Specifications

Drives

PowerVault MD3200 Up to twelve 3.5-inch SAS hot-swappable

hard drives (3.0 Gbps and 6.0 Gbps)

PowerVault MD3220 Up to twenty four 2.5-inch SAS hot-swappable

hard drives (3.0 Gbps and 6.0 Gbps)

RAID Controller Modules

RAID controller modules

• One or two hot-swappable modules with

temperature sensors

• 2 GB of cache per controller

Back-Panel Connectors (Per RAID Controller Module)

SAS connectors

• Four SAS IN ports to connect hosts

• One SAS OUT port for expansion to an additional

PowerVault MD1200 series enclosure

NOTE:

SAS connectors are SFF-8088 compliant.

Serial connector One 6-pin mini-DIN connector

NOTE:

For technical support use only.

Management Ethernet

connector

One 100/1000 Base-T port Ethernet for out-of-band

management of the enclosure

NOTE:

The default management port IP addresses for

the primary and secondary RAID controller modules

are 192.168.128.101 and 192.168.128.102, respectively.

By default, the management ports are set to Dynamic

Host Configuration Protocol (DHCP). If the controller

is unable to get an IP address configuration from

a DHCP server within a specified time out period

(approximately 3 minutes), it defaults back to

static IP addressing. For more information,

see the Deployment Guide.

Getting Started With Your System

13

Expansion

PowerVault MD1200 series Supports a maximum of 192 hard drives with any

combination of PowerVault MD1200 or PowerVault

MD1220 expansion enclosures. Support for 192 hard

drives is a Premium Feature and requires activation.

The maximum number of hard drives supported

without using the Premium Feature is 120.

Redundant path connectivity provides redundant

data paths to each hard drive.

Backplane Board

Connectors

• 12 or 24 SAS hard-drive connectors

• Two power supply/cooling fan module connectors

• Two sets of RAID controller module connectors

• One control panel connector for front LEDs and

system identification button

Sensors Two temperature sensors

LED Indicators

Front panel

• One two-color LED indicator for system status

• Two single-color LED indicators for power and

enclosure mode

NOTE:

The enclosure mode LED is not applicable to

the PowerVault MD3200 series storage array.

Hard-drive carrier

• One single-color activity LED

• One two-color LED status indicator per drive

Power supply/cooling fan Three LED status indicators for power supply status,

power supply/fan fault, and AC status

14

Getting Started With Your System

RAID controller module Six single-color LEDs:

• One battery fault

• One cache active

• One controller fault

• One controller power

• One system identification

• One management Ethernet activity

Six two-color LEDs:

• Four SAS IN link or fault

• One SAS OUT link or fault

• One management Ethernet link speed

Switch

System identification button Located on the front control panel. This button is

used to locate a system within a rack.

Enclosure mode switch Located on the front of the system. This switch is

not applicable to the PowerVault MD3200 series

storage array.

Password reset switch Located on the back-panel of the RAID controller

module. This switch is used to reset the storage array

password.

Power Supplies

AC power supply (per power supply)

Wa tt ag e

600 W

Voltage

100–240 VAC (8.6 A–4.3 A)

Heat dissipation

100 W

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush current

may reach a maximum of 55 A per power supply for

10 ms or less.

LED Indicators (continued)

Getting Started With Your System

15

Available Hard Drive Power (Per Slot)

PowerVault MD3200 25 W

PowerVault MD3220 12 W

RAID Controller Module Power (Per Slot)

Maximum power consumption 100 W

Physical

PowerVault MD3200

Height

8.68 cm (3.41 inches)

Width

44.63 cm (17.57 inches)

Depth

60.20 cm (23.70 inches)

Weight (maximum

configuration)

29.30 kg (64.6 lb)

Weight (empty)

8.84 kg (19.5 lb)

PowerVault MD3220

Height

8.68 cm (3.41 inches)

Width

44.63 cm (17.57 inches)

Depth

54.90 cm (21.61 inches)

Weight (maximum

configuration)

24.22 kg (53.4 lb)

Weight (empty)

8.61 kg (19 lb)

16

Getting Started With Your System

Environmental

NOTE:

For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Tem perat ure

Operating

10 °C to 35 °C (50 °F to 95 °F) with a maximum

temperature gradation of 10 °C per hour

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–40 °C to 65 °C (–40 °F to 149 °F) with a maximum

temperature gradation of 20°C per hour.

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.25 G at 3–200 Hz for 15 min

Storage

0.5 G at 3–200 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse on

each side of the system) of 31 G for 2.6 ms in the

operational orientation

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse on

each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G1 as defined by ISA-S71.04-1985

Page is loading ...

Dell PowerVault MD3200 Series Quick start guide

This manual is also suitable for

Dell PowerVault MD3200 Series Quick start guide

in other languages

Related papers

Other documents