American Standard Innsbrook Lavatory Faucet M968498 User manual

American Standard
Brand
American Standard
Model
Innsbrook Lavatory Faucet M968498
Category
Sanitary ware
Type
User manual
(In Toronto Area only: 1-905-3061093)
Innsbrook Lavatory Faucet
with SELECTRONIC™ Technology
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
605XTMV
6055.202
6055.205
PRODUCT No.s
6056.202
6056.205
6057.202
6057.205
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
© 2005 American Standard
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
M968498 Rev.1.2
Certified to comply with ASME A112.18.1M
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
MOUNTING
SURFACE
Roughing-in Dimensions
10'
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction 4" center to center mounting.
Operates on DC (battery) or AC permanent power. In-line
strainer for solenoid is integral. Single inlet 3/8 compression,
built-in checks, and flexible stainless steel 15" reach inlet
hose for spout connection.
INSTALL SPOUT ASSEMBLY;
Fig. 3
INSTALLATION
CAUTION
Turn off hot and cold water
supplies before beginning
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2. Insert WIRES (3), FLEX HOSE (4) and STUDS (5)
through holes of mounting surface. Fig. 1a.
3. From under side of mounting surface install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
4. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.
Fig. 1a
1
2
114mm
(4-1/2)
508mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
175mm
(6-7/8)
162mm
(6-3/8)
155mm
(6-1/8)
102mm
(4)
35mm
(1-3/8)
DIA.
3 HOLES
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
108mm
(4-1/4)
57mm
(2-1/4)
1
6
5
2
4
3
6
5
5
Fig. 1b
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
5b. AC Power Supply (for 6056 series)
5c. 10 ft. Extension Wire (for 6057 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 6055 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
(In Toronto Area only: 1-905-3061093)
Innsbrook Lavatory Faucet
with SELECTRONIC™ Technology
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
605XTMV
6055.202
6055.205
PRODUCT No.s
6056.202
6056.205
6057.202
6057.205
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
© 2005 American Standard
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
M968498 Rev.1.2
Certified to comply with ASME A112.18.1M
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
MOUNTING
SURFACE
Roughing-in Dimensions
10'
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction 4" center to center mounting.
Operates on DC (battery) or AC permanent power. In-line
strainer for solenoid is integral. Single inlet 3/8 compression,
built-in checks, and flexible stainless steel 15" reach inlet
hose for spout connection.
INSTALL SPOUT ASSEMBLY;
Fig. 3
INSTALLATION
CAUTION
Turn off hot and cold water
supplies before beginning
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2. Insert WIRES (3), FLEX HOSE (4) and STUDS (5)
through holes of mounting surface. Fig. 1a.
3. From under side of mounting surface install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
4. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.
Fig. 1a
1
2
114mm
(4-1/2)
508mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
175mm
(6-7/8)
162mm
(6-3/8)
155mm
(6-1/8)
102mm
(4)
35mm
(1-3/8)
DIA.
3 HOLES
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
108mm
(4-1/4)
57mm
(2-1/4)
1
6
5
2
4
3
6
5
5
Fig. 1b
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
5b. AC Power Supply (for 6056 series)
5c. 10 ft. Extension Wire (for 6057 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 6055 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
(In Toronto Area only: 1-905-3061093)
Innsbrook Lavatory Faucet
with SELECTRONIC™ Technology
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
605XTMV
6055.202
6055.205
PRODUCT No.s
6056.202
6056.205
6057.202
6057.205
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
© 2005 American Standard
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
M968498 Rev.1.2
Certified to comply with ASME A112.18.1M
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
MOUNTING
SURFACE
Roughing-in Dimensions
10'
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction 4" center to center mounting.
Operates on DC (battery) or AC permanent power. In-line
strainer for solenoid is integral. Single inlet 3/8 compression,
built-in checks, and flexible stainless steel 15" reach inlet
hose for spout connection.
INSTALL SPOUT ASSEMBLY;
Fig. 3
INSTALLATION
CAUTION
Turn off hot and cold water
supplies before beginning
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2. Insert WIRES (3), FLEX HOSE (4) and STUDS (5)
through holes of mounting surface. Fig. 1a.
3. From under side of mounting surface install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
4. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.
Fig. 1a
1
2
114mm
(4-1/2)
508mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
175mm
(6-7/8)
162mm
(6-3/8)
155mm
(6-1/8)
102mm
(4)
35mm
(1-3/8)
DIA.
3 HOLES
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
108mm
(4-1/4)
57mm
(2-1/4)
1
6
5
2
4
3
6
5
5
Fig. 1b
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
5b. AC Power Supply (for 6056 series)
5c. 10 ft. Extension Wire (for 6057 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 6055 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
(In Toronto Area only: 1-905-3061093)
Innsbrook Lavatory Faucet
with SELECTRONIC™ Technology
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
605XTMV
6055.202
6055.205
PRODUCT No.s
6056.202
6056.205
6057.202
6057.205
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
© 2005 American Standard
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
M968498 Rev.1.2
Certified to comply with ASME A112.18.1M
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
MOUNTING
SURFACE
Roughing-in Dimensions
10'
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction 4" center to center mounting.
Operates on DC (battery) or AC permanent power. In-line
strainer for solenoid is integral. Single inlet 3/8 compression,
built-in checks, and flexible stainless steel 15" reach inlet
hose for spout connection.
INSTALL SPOUT ASSEMBLY;
Fig. 3
INSTALLATION
CAUTION
Turn off hot and cold water
supplies before beginning
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2. Insert WIRES (3), FLEX HOSE (4) and STUDS (5)
through holes of mounting surface. Fig. 1a.
3. From under side of mounting surface install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
4. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.
Fig. 1a
1
2
114mm
(4-1/2)
508mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
175mm
(6-7/8)
162mm
(6-3/8)
155mm
(6-1/8)
102mm
(4)
35mm
(1-3/8)
DIA.
3 HOLES
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
108mm
(4-1/4)
57mm
(2-1/4)
1
6
5
2
4
3
6
5
5
Fig. 1b
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
5b. AC Power Supply (for 6056 series)
5c. 10 ft. Extension Wire (for 6057 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 6055 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
'JHB
'JHC
3FNPWF&/$-0463&$07&3'JH
'FFEUIF8*3&$0//&$5034UISPVHIUIFUPQ
PG&/$-0463&'JHB
3FNPWF(30..&5GSPN&/$-0463'JH
'FFEUIFHSBZ4&/4038*3&UISPVHI
(30..&5GSPN$0//&$503'JHCE
*OTFSUHSBZ4&/4038*3&JOUP41-*51-6(
1VTI41-*51-6(JOUP(30..&5UPTFBM
'JHE
*OTFSU(30..&5CBDLJOUP&/$-0463&
'JHD
*OTUBMM#"55&3:POUP%$DJSDVJUCPBSE'JHF
/PUF'PS#"55&3:1"$,JOTUBMMBUJPOTFF*OTUBMM
#BUUFSZQBHF
*OTUBMM$*3$6*5#0"3%JOUP&/$-0463&
XJUI4&/4038*3&VOEFS#0"3%'JHD
*OTFSU4&/4038*3&$0//&$503JOUP
$*3$6*5#0"3%3&$&1503'JHF
$POOFDUXJSFTGSPN4&/403UP40-&/0*%7"-7&
3FEUP#MBDLUP'JHD
3FQMBDF&/$-0463&$07&35JHIUFODPWFS
TDSFXTGJSNMZ
%$7&34*0/#"55&3:'JH
#-"$,
3&%
&-&$53*$"-*/45"--"5*0/
'JHD
'JHE


'JHF
'JH

'JH
'JHC
3FNPWF&/$-0463&$07&3'JH
'FFEUIF8*3&$0//&$5034UISPVHIUIFUPQ
PG&/$-0463&'JHB
3FNPWF(30..&5GSPN&/$-0463'JH
'FFEUIFHSBZ4&/4038*3&UISPVHI
(30..&5GSPN$0//&$503'JHC*OTFSU
HSBZ4&/4038*3&JOUP41-*51-6(1VTI
41-*51-6(JOUP(30..&5UPTFBM'JHF
*OTFSU(30..&5CBDLJOUP&/$-0463&
'JHE
3FNPWF41-*51-6(GSPN108&34611-:
(30..&5*OTFSU108&3$03%$0//&$503
UISPVHI108&34611-:(30..&5*OTFSU
108&3$03%JOUP41-*51-6(1VTI
41-*51-6(JOUP108&34611-:(30..&5
UPTFBM'JHH
*OTFSU108&34611-:$0//&$503JOUP
3&$&1503POUIF$*3$6*5#0"3%'JHD
*OTUBMM$*3$6*5#0"3%JOUP&/$-0463&
XJUI4&/4038*3&VOEFS#0"3%'JHE
*OTFSU4&/4038*3&$0//&$503JOUP
$*3$6*5#0"3%3&$&1503TMPU'JHG
$POOFDUXJSFTGSPN4&/403UP40-&/0*%
7"-7&3FEUP#MBDLUP'JHE
3FQMBDF&/$-0463&$07&35JHIUFODPWFS
TDSFXTGJSNMZ
"$7&34*0/'JH
108&3
4611-:
$03%
3&%
'JHE
'JHF

'JHG
'JHD

$"65*0/
#FGPSFPQFOJOH&/$-0463&
EJTDPOOFDU"$QPXFSTVQQMZ





'JHH

#-"$,
'JHB
'03"$7&34*0/
.6-5*)00,61'JH
6OJU 6OJU 6OJU
4FF"$7FSTJPO&MFDUSJDBM)PPLVQGPSGJSTUVOJUPG
UIF.VMUJIPPLVQ
3FNPWF&/$-0463&$07&34GSPNBMM
&/$-0463&4
3FNPWF40-*%#-"$,*/4&35GSPNSJHIUTJEF
PG&/$-0463&BOESFQMBDFXJUIHSBZ1*&$&
(30..&53FQMBDFTPMJECMBDLJOTFSUTPO6OJU
XJUIHSBZ1*&$&(30..&5
5BLFUIFGU&95&/4*0/GSPN6OJUBOE
JOTUBMMJOUPSJHIUTJEFPG6OJUBOE-FGUTJEFPG6OJU
JOTFBMJOHXJSFJOUP41-*51-6(BTTIPXOJO'JH
1VTI41-*51-6(JOUP(30..&5
*OTFSU$0//&$503GSPNGU&95&/4*0/
JOUP$*3$6*5#0"3%3&$&1503UPQPG6OJU
BTTIPXOJO'JH
*OTFSUPUIFSFOEPGGU&95&/4*0/JOUP-08&36
(30..&5PG6OJUBQQSPYJNBUFMZGSPN
DPOOFDUPS'JH1VTI41-*51-6(JOUP
(30..&5UPTFBM
*OTFSUDPOOFDUPSPGGU&95&/4*0/JOUPMPXFS
SFDFQUPSBTTIPXOJO'JHPO$*3$6*5#0"3%PG
6OJU
'FFEHSBZTFOTPSXJSFGSPN6OJUUISPVHIVQQFS
6(30..&5PG6OJU&/$-0463&GSPN
DPOOFDUPS'JH*OTFSUXJSFJOUP41-*51-6(
1VTI41-*51-6(JOUP(30..&5UPTFBM'JH

*OTFSU(30..&5CBDLJOUP&/$-0463&'JHB
3FJOTUBMM$JSDVJU#PBSEJOUP&ODMPTVSFXJUIBMM
XJSFTVOEFS#PBSE'JHB
$POOFDU6OJU3FEBOE#MBDL4FOTPSXJSFT5P
TPMFOPJEWBMWF3FEUP#MBDLUP'JHB
3FQFBU4UFQTUISPVHIGPSSFNBJOJOH6OJUTJO
.VMUJ)PPLVQ
'JH
'JH
TWO PIECE
GROMMET
TWO PIECE
GROMMET
1
1
1
'FFEUIFHSBZGU&95&/4*0/UISPVHI306/%
(30..&54BOE6(30..&54BTJMMVTUSBUFEBCPWF
2
7
2
8
RED
3
BLACK
1
'JHB
4"
."*/5&/"/$&
8IFOUIF4FOTPSEFUFDUTBVTFSUIFXBUFS
JNNFEJBUFMZTUBSUTUPGMPX8BUFSGMPXXJMMTUPQ5XP
TFDPOETBGUFSVTFSJTPVUPGTFOTPSSBOHF5IFPGG
EFMBZBMMPXTUIFVTFSUPDPNGPSUBCMZNPWFIJTIBOET
XJUIPVUUIFGMPXDZDMJOHPOUPPGG"TBQSFDBVUJPOB
TBGFUZUJNFSXJMMUVSOPGGUIFXBUFSBGUFSUIFTFOTPSIBT
CFFOCMPDLFEGPSTFDPOET5IFXBUFSXJMMTUBZPGG
VOUJMUIFCMPDLBHFJTSFNPWFEGSPNUIFEFUFDUJPO[POF
%FUFDUJPO;POFNNNN
%FGBVMU4FUBU'BDUPSZNN
'JH
)"/%8"4)4&/40301&3"5*0/
'JH
5PJOTUBMM/FX#"55&3:BMJHOBOEQSFTTEPXO
#"55&3:DPOUBDUTGBDJOHEPXOXBSEJOUPQPTJUJPO
VOUJMUBCTMPDLJOUPQMBDF
5PSFNPWFUIF#"55&3:TQSFBEUIFUXPUBCTPO
UIF)0-%&3XJUIZPVSUIVNCT5IF#"55&3:
XJMMSFMFBTF
3FNPWFUIF0-%#"55&3:
*OTUBMM/&8#"55&3:DPOUBDUTGBDJOH
EPXOXBSEJOUP)0-%&3BOEQSFTTEPXOJOUP
QPTJUJPOVOUJMUBCTMPDLJOUPQMBDF
'JH
)0850*/45"--"/%$)"/(&
#"55&3:'JH
1
1
2
#"55&3:)0-%&3
-0$,*/(5"#4
4FUUJOHUIF%FUFDUJPO;POF%JTUBODF
3FNPWFDPWFSGSPN&/$-0463&%JTDPOOFDU(3":
4&/4038*3&GSPNDJSDVJUCPBSEUIFOSFDPOOFDU
8IJMFUIF4&/403$0/530--&%JTCMJOLJOH
TMPXMZQMBDFZPVSIBOEJONNJOGSPOUPG
UIFTFOTPS'JHB
8IFOUIF-&%TUPQTCMJOLJOHBOETUBZT0/NPWF
ZPVSIBOEUPUIFEFTJSFEQPTJUJPOBOEIPMEJOQMBDF
VOUJMUIF-&%CFHJOTUPCMJOLBHBJO'JHB
0ODFUIF4&/403$0/530--&%CFHJOTUP
CMJOLBHBJOSFNPWFZPVSIBOEGSPNUIFEFUFDUJPO[POF
8IFOUIFGMBTIJOHTUPQTUIFEFUFDUJPOEJTUBODFJTTFU
)0850$)"/(&4&/403
3"/(&'BDUPSZTFUBU'JH
'JH
'JHB
'JH
NNNN
#-*/,*/(-&%
6150NN
#-*/,*/(
-&%
1
2
2
5
6
4
10
3
%&5&$5*0/
;0/&
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
Fig.6
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
10
M 9 6 8 4 9 8 R e v . 1 . 2 M 9 6 8 4 9 8 R e v . 1 . 2
INNSBROOK with
SELECTRONIC
LAVATORY FAUCETS
CHROME 002
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pro d uct nam e s l i ste d he r ein are tra d ema r ks o f A m eri c an S tan d ard Inc .
© A m eri c an S tan d ard Inc . 20 0 5
A923672-0070A
FAUCET SUPPLY
HOSE
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
044912-0070A
MOUNTING NUT
A950223-007L0A
SENSOR (LAVY)
M923115-0070A
PUTTY PLATE
M962409-0070A
SENSOR KIT
6055.202
6055.205
6056.202
6056.205
6057.202
6057.205
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
IN MEXICO 01-800-839-12-00
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
Fig.6
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
10
M 9 6 8 4 9 8 R e v . 1 . 2 M 9 6 8 4 9 8 R e v . 1 . 2
INNSBROOK with
SELECTRONIC
LAVATORY FAUCETS
CHROME 002
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pro d uct nam e s l i ste d he r ein are tra d ema r ks o f A m eri c an S tan d ard Inc .
© A m eri c an S tan d ard Inc . 20 0 5
A923672-0070A
FAUCET SUPPLY
HOSE
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
044912-0070A
MOUNTING NUT
A950223-007L0A
SENSOR (LAVY)
M923115-0070A
PUTTY PLATE
M962409-0070A
SENSOR KIT
6055.202
6055.205
6056.202
6056.205
6057.202
6057.205
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
IN MEXICO 01-800-839-12-00
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
Fig.6
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
10
M 9 6 8 4 9 8 R e v . 1 . 2 M 9 6 8 4 9 8 R e v . 1 . 2
INNSBROOK with
SELECTRONIC
LAVATORY FAUCETS
CHROME 002
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pro d uct nam e s l i ste d he r ein are tra d ema r ks o f A m eri c an S tan d ard Inc .
© A m eri c an S tan d ard Inc . 20 0 5
A923672-0070A
FAUCET SUPPLY
HOSE
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
044912-0070A
MOUNTING NUT
A950223-007L0A
SENSOR (LAVY)
M923115-0070A
PUTTY PLATE
M962409-0070A
SENSOR KIT
6055.202
6055.205
6056.202
6056.205
6057.202
6057.205
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
IN MEXICO 01-800-839-12-00
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
Fig.6
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
10
M 9 6 8 4 9 8 R e v . 1 . 2 M 9 6 8 4 9 8 R e v . 1 . 2
INNSBROOK with
SELECTRONIC
LAVATORY FAUCETS
CHROME 002
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pro d uct nam e s l i ste d he r ein are tra d ema r ks o f A m eri c an S tan d ard Inc .
© A m eri c an S tan d ard Inc . 20 0 5
A923672-0070A
FAUCET SUPPLY
HOSE
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
044912-0070A
MOUNTING NUT
A950223-007L0A
SENSOR (LAVY)
M923115-0070A
PUTTY PLATE
M962409-0070A
SENSOR KIT
6055.202
6055.205
6056.202
6056.205
6057.202
6057.205
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
IN MEXICO 01-800-839-12-00
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

American Standard Innsbrook Lavatory Faucet M968498 User manual

American Standard
Brand
American Standard
Model
Innsbrook Lavatory Faucet M968498
Category
Sanitary ware
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents