Medion X51 Operating instructions

Category
Mini PCs
Type
Operating instructions

This manual is also suitable for

Operating instructions
Multimedia PC
High-performance PC X50/X51
High-performance PC X71
High-performance PC X75
8
9
10
4
1
11
6
7
27 2 24
5
23
17
15
16
18
26
25
24
20
13
14
19
2
7
6
5
21
22
12
Multimedia PC
Click on the number of a control element to go to the relevant section in the operating instructions.
High-performance PC X50/X51
Click on the number of a control element to go to the relevant section in the operating instructions.
12 1
8
23
10
11
26
16
19
6
24
25
2
27
7
3
2
6
14
5
21
6
High-performance PC X71
Click on the number of a control element to go to the relevant section in the operating instructions.
23
13
15
14
22
20
21
24
6
5
7
19
2
26
16
12
1817
25
5
76
272
1
11
8
9
10
High-performance PC X75
Click on the number of a control element to go to the relevant section in the operating instructions.
3
23
14
15
19/27
226
725
24
6
5
21
22
20
13
1 12
11
8
9
10
16
Connections
1 On/o switch/operating mode
2 Microphone socket*
3 Slot for Medion HDDrive2Go super-speed external hard drive*
4 Front panel*
5 eSATA connection*
6 USB 2.0 ports*
7 USB 3.0 ports*
8 Optical drive
9 Optical drive eject button
10 Hot-swap mobile rack*
11 Card reader*
12 Overclocking button*
13 D-Sub VGA monitor connection*
14 DVI-I/DVI-D monitor connection*
15 Mini HDMI connection*
16 HDMI connection*
17 TV aerial socket (analogue & DVB-T)*
18 TV aerial socket (DVB-S)*
19 Speaker/headphones*
20 Clear CMOS*
21 Optical/coaxial digital S/PDIF audio output*
22 PS/2 connection
23 Power supply (mains cable socket & mains switch)
24 IEEE 1394 (FireWire)*
25 LAN network (RJ45)
26 Audio input (line In, music recording)
27 Headphone socket*
*optional
1 of 36
Contents
1. About these instructions ........................................................................................................................................................ 4
1.1. Warning symbols and key words used in these instructions .....................................................................................................................4
1.2. Proper use .....................................................................................................................................................................................................................4
1.3. Declaration of conformity .......................................................................................................................................................................................4
2. Safety instructions ..................................................................................................................................................................5
2.1. Dangers for children and people with reduced ability to operate machinery ....................................................................................5
2.2. Operational safety ......................................................................................................................................................................................................5
2.3. Never carry out repairs yourself ........................................................................................................................................................................... 5
2.4. Data backup .................................................................................................................................................................................................................5
3. Package contents .................................................................................................................................................................... 6
4. Setting up the PC .....................................................................................................................................................................6
4.1. Installation location ................................................................................................................................................................................................... 6
4.2. Environmental requirements .................................................................................................................................................................................6
4.3. Ergonomics ...................................................................................................................................................................................................................6
5. Connecting ............................................................................................................................................................................... 8
5.1. Connecting the cables ............................................................................................................................................................................................. 8
5.2. Opening and closing the front panel (optional) .............................................................................................................................................8
5.3. Connecting the microphone (optional) .............................................................................................................................................................8
5.4. Connecting SATA devices (optional) ...................................................................................................................................................................9
5.5. Connecting USB devices (optional) .....................................................................................................................................................................9
5.6. Overclocking button (optional) ..........................................................................................................................................................................10
5.7. Connecting a monitor (optional) ........................................................................................................................................................................11
5.8. Connecting devices using the mini-HDMI socket (optional) ....................................................................................................................11
5.9. Connecting a HDMI device (optional) ...............................................................................................................................................................11
5.10. Connecting audio output / headphones /
speakers ..............................................................................................................................................................................................................................11
5.11. Connecting PS/2 devices (optional) ................................................................................................................................................................11
5.12. Connecting IEEE 1394 (FireWire) devices (optional)..................................................................................................................................12
5.13. Connecting a network (LAN) ............................................................................................................................................................................12
5.14. Aerial socket for TV reception (optional) .......................................................................................................................................................12
5.15. Analogue TV reception ........................................................................................................................................................................................12
5.16. DVB-T TV reception ................................................................................................................................................................................................12
5.17. DVB-S TV reception ...............................................................................................................................................................................................12
5.18. Connecting audio input/recording source ...................................................................................................................................................12
5.19. Connecting power supply ..................................................................................................................................................................................12
6. First use .................................................................................................................................................................................13
6.1. Starting up the PC ....................................................................................................................................................................................................13
7. The mouse ..............................................................................................................................................................................14
8. The keyboard .........................................................................................................................................................................14
8.1. The Alt, Alt Gr and Ctrl buttons ...........................................................................................................................................................................14
9. The hard drive .......................................................................................................................................................................15
9.1. Important directories ..............................................................................................................................................................................................15
9.2. Hot-swap mobile rack (optional) ........................................................................................................................................................................16
9.3. Connecting an external hard drive (optional) ................................................................................................................................................16
10. The optical drive (optional) ................................................................................................................................................17
10.1. Load disc ...................................................................................................................................................................................................................17
10.2. Playing/reading discs ...........................................................................................................................................................................................17
10.3. Blank CDs and DVDs .............................................................................................................................................................................................17
11. The card reader (optional) ..................................................................................................................................................18
11.1. Inserting the memory card .................................................................................................................................................................................18
11.2. Removing memory cards ....................................................................................................................................................................................18
12. The graphics system (optional) ..........................................................................................................................................19
12.1. Appearance and customisation ........................................................................................................................................................................19
13. The sound system ...............................................................................................................................................................19
14. IEEE 1394 (FireWire) (optional) ..........................................................................................................................................20
14.1. Possible uses for IEEE 1394 ................................................................................................................................................................................20
14.2. Technical specifications .......................................................................................................................................................................................20
2 of 36
15. USB connection (optional) ..................................................................................................................................................20
16. The TV card (optional) .........................................................................................................................................................20
17. Networking ..........................................................................................................................................................................20
17.1. What is a network? ...............................................................................................................................................................................................20
17.2. Wireless LAN (wireless network) .......................................................................................................................................................................21
18. Software ...............................................................................................................................................................................21
18.1. Getting to know Windows
®
8 .............................................................................................................................................................................21
18.2. indows activation ...................................................................................................................................................................................................21
18.3. Windows® 8 – Whats New ..................................................................................................................................................................................22
18.4. Overview ...................................................................................................................................................................................................................23
18.5. Linking a user account to a LiveID ...................................................................................................................................................................24
19. Control Panel .......................................................................................................................................................................27
19.1. Control panel settings ..........................................................................................................................................................................................28
19.2. Resetting the PC to its factory settings ..........................................................................................................................................................28
19.3. BIOS Setup ...............................................................................................................................................................................................................28
19.4. Clear CMOS (optional) ..........................................................................................................................................................................................29
19.5. Kaspersky Internet Security ................................................................................................................................................................................29
19.6. Windows
®
8 – Help and support .......................................................................................................................................................................30
20. FAQ – Frequently asked questions .....................................................................................................................................30
21. Customer service .................................................................................................................................................................30
21.1. First aid in the case of hardware problems ..................................................................................................................................................30
21.2. Find the cause .........................................................................................................................................................................................................30
21.3. Faults and possible causes ..................................................................................................................................................................................31
21.4. Do you need more help? .....................................................................................................................................................................................31
21.5. Driver support .........................................................................................................................................................................................................31
21.6. Transport ..................................................................................................................................................................................................................31
21.7. Cleaning and care ..................................................................................................................................................................................................32
22. Upgrades/modifications and repairs .................................................................................................................................32
23. Recycling and disposal .......................................................................................................................................................33
23.1. Handling batteries .................................................................................................................................................................................................33
23.2. FCC Compliance Statement ...............................................................................................................................................................................33
24. Index .....................................................................................................................................................................................34
3 of 36
Personal information
Please append the following to your proof of ownership:
Serial numbers ...... ..........................................
(e.g. Microsoft®) ................................................
Purchase date, location ................................................
You will find the serial number on the back of the PC. Where applicable, also copy the number on your warranty documents.
Our target group
This operating manual is intended to be read by both first-time and experienced users. Regardless of any possible profession-
al use, this PC is designed for use in a private household. The entire family will be able to enjoy the wide variety of applications
it offers.
The quality
We select our components with a close eye to functionality, ease of use, safety and reliability. Thanks to our ideally balanced
hardware/software concept we are able to offer you a state-of-the-art machine that you will enjoy whether you are working or
at play. Thank you for purchasing our products. We are delighted to welcome you as our new customer.
Copying this manual
This document contains legally protected information. All rights reserved. Mechanical, electronic and any other form of repro-
duction is prohibited without the written permission of the manufacturer.
Copyright 2012.
All rights reserved.
This operating manual is protected by copyright.
MEDION® is the owner of this copyright.
Trademarks:
MS-DOS® and Windows® are registered trademarks of the Microsoft
®
corporation.
Intel, the Intel Logo, Intel Inside, Intel Core, Ultrabook, and Core Inside are trademarks of Intel Corporation in the U.S. and/or
other countries.
Other trademarks are the property of their respective owners.
Subject to technical and optical changes as well as printing errors.
4 of 36
1. About these instructions
Read these erating instructions carefully before using the device for the first time. Note the warnings on the device
and in the operating instructions.
Always keep the operating instructions close to hand. If you sell the appliance or give it away, please ensure that
you also pass on these instructions.
1.1. Warning symbols and key words used in these instructions
DANGER!
Warning: immediate mortal danger!
WARNING!
Warning: possible mortal danger and/or serious irreversible injuries!
CAUTION!
Please follow the guidelines to avoid injuries and/or property damage.
ATTENTION!
Please follow the guidelines to avoid property damage.
PLEASE NOTE!
Additional information on using the device.
PLEASE NOTE!
Please follow the guidelines in the operating instructions.
WARNING!
Warning: danger of electric shock!
Bullet point/information on operating steps and results
Tasks to be performed
1.2. Proper use
This device is intended for the use, management and editing of electronic documents and multimedia content and is only in-
tended for personal use, not industrial/commercial use.
Please note that we shall not be liable in cases of improper use:
Do not modify the device without our consent and do not use any auxiliary equipment which we have not approved or
supplied.
Use only spare parts and accessories which we have supplied or approved.
Follow all the instructions in these operating instructions, especially the safety information. Any other use is deemed im-
proper and can cause personal injury or damage to the product.
Do not use the device in extreme environmental conditions.
1.3. Declaration of conformity
The telephone is delivered with the following wireless features:
Wireless LAN (optional)
• Keyboard (optional)
• Mouse (optional)
Due to the output of the integrated wireless LAN solution, the device may only be used inside buildings in France. There are
currently no restrictions in any other EU countries. When using the device in other countries, please find out about the rele-
vant legal regulations.
Medion AG hereby declares that this device conforms to the fundamental requirements and the remaining relevant regula-
tions of the 1999/5/EC R&TTE Directive.
This product satisfies the basic requirements and relevant regulations of the Ecodesign Directive 2009/125/EC.
Full declarations of conformity are available at http://www.medion.com/conformity.
5 of 36
2. Safety instructions
2.1. Dangers for children a nd people with reduced ability to operate
machinery
This device is not intended for use by people (including children) with reduced physical, sensory or mental abilities or for
those without experience and/or knowledge, unless they are supervised by a person responsible for their safety or they
have been instructed in its use.
Children should be supervised to ensure that they do not play with the device. Children should not be allowed to use this
device without supervision.
Keep the device and its accessories out of reach of children.
DANGER!
Keep plastic packaging out of the reach of children. There is a risk of suffocation.
2.2. Operational safety
Please read this section carefully and follow all instructions provided. The instructions will help you to operate the PC reliably
and help lengthen its service life.
Never open the housing of the PC, battery or mains adapter! This could result in an electric shock or even ignite a fire
which will damage your PC.
Never open the housing of the PC! There is a risk of electric shock when the housing is open. Never operate the PC when
the housing is open.
The optical drives (CDRW, DVD, DVD-RW) are classified as laser class 1 equipment, as long as the housing of the optical
drive has not been removed. Do not remove the cover of the drive because invisible laser radiation can escape.
Do not insert anything into the PC through the slots and openings. This could result in an electrical short-circuit, an electric
shock or even ignite a fire which will damage your PC.
The slots and openings on the PC are for ventilation purposes. Do not cover these openings as this could cause the device
to overheat. When setting up the PC, ensure a minimum clearance of 20 cm on all sides.
Avoid exposing the device to water droplets or spray and do not place any water-filled containers – such as vases – on the
device. Liquids penetrating the device may impair the electrical safety of the product.
Turn off the PC immediately/do not turn on the PC in the first place and contact the customer service department if ...
... the mains cable or the attached plug is scorched or damaged. Replace defective mains adapters/mains cables with original
parts only. These parts should not be repaired under any circumstances.
... the PC housing is damaged or liquid has penetrated it. Have the PC checked first by the customer service department.
Otherwise, it may not be possible to safely operate the PC and there may be a risk to life due to electric shock.
2.3. Never carry out repairs yourself
WARNING!
Never try to open or repair the device yourself. There is a risk of electric shock.
If there is a fault, contact the MEDION Service Centre or other suitable specialist workshop.
2.4. Da ta backup
ATTENTION!
Back up your data to external storage media before each update. We do not accept any liability for claims for compen-
sation arising from loss of data or any consequential loss or damage.
6 of 36
3. P ackage contents
Please check your purchase to ensure that all items are included. If anything is missing, please contact us within 14 days of
purchase. Note down the serial numbers here.
The PC you have purchased includes the following components:
PC and connection cable
Windows keyboard and mouse (optional)
OEM version of the operating system (optional)
• Documentation
DANGER!
Keep packaging material such as plastic film away from children. There is a risk of suffocation if used
improperly.
4. Setting up the PC
Setting up your PC correctly goes a long way towards ensuring comfortable operation.
4.1. Installation location
Keep your PC and all connected devices away from moisture and avoid dust, heat and direct sunlight. This will help to
avoid malfunctions or damage to the PC.
Place all devices onto a stable, flat and vibration-free surface and only operate them on this type of surface in order to pre-
vent the PC malfunctioning.
4.2. Environmental requirements
The PC can be operated at ambient temperatures of +10°C to +35°C and a relative humidity of 30%–70% (non-condens-
ing).
When switched off, the PC can be stored at temperatures from −20 to 50.
Pull out the mains plug during thunder storms and, in particular, remove the aerial cable (if present). For extra safety, we
recommend using an overvoltage protection device to prevent the PC from sustaining damage as a result of power surges
or lightning strikes.
After transporting the PC, wait until the device has reached ambient temperature before switching it on. Large changes in
temperature or fluctuations in humidity can cause moisture build-up within the PC due to condensation. This can cause an
electrical short circuit.
4.3. Ergonomics
PLEASE NOTE!
Avoid dazzle, reflections and strong bright-dark contrast in order to protect your eyes.
The monitor should never be placed next to a window because this is the brightest part of the room during daylight. This
brightness can make it more difficult for the eyes to adjust to the darker monitor.
Always place the monitor so that the direction of vision is parallel to the window front (see image).
This parallel direction of vision should also be maintained in relation to any artificial lighting equipment. In other words, the
same criteria and principles apply where the workspace is illuminated with artificial light.
Where it is not possible to position the monitor as described, the following measures may be useful:
rotating, lowering or tilting the monitor;
using slats or vertical blinds on the windows;
using partitions or changing the direction of the light source.
PLEASE NOTE!
Take regular breaks when working at your monitor to prevent tenseness and fatigue.
7 of 36
Sitting for long periods without changing your position can be uncomfortable. To minimise the risks of physical discomfort or
damage, correct posture is paramount.
General – Alter your position frequently (every 20–30 minutes) and take frequent breaks to avoid fatigue.
BackWhen sitting at your workplace, the backrest of the office chair should be upright or tilted slightly backwards to
supported your back.
ArmsYour arms and elbows should be relaxed and loose. Keep your elbows tucked in next to your body. Keep your fore-
arms and hands almost parallel to the floor.
Wrists – When working with the keyboard, mouse or trackball, your wrists should be kept as straight as possible and should
not be bent at an angle greater than 10°.
LegsYour thighs should lie horizontally or be tilted slightly upwards. Your lower legs should kept at an angle of approxi-
mately 90° to your thighs. Your feet should rest flat on the floor. Where possible, use a footrest, otherwise, ensure that the
seat is adjusted to the correct height before starting work.
HeadYour head should be kept straight or inclined slightly forward. Do not work with your head or upper body twisted.
Hand rest area: 5–10 cm
Viewing distance: 50 to 70 cm
Leg room (vertical): 65 cm (min.)
Leg room (horizontal): 60cm (min.)
The top line of the screen should be at eye height or a little below.
8 of 36
5. Connecting
For better orientation, please open out the left-hand inside cover page to fully display the diagrams showing the positions of
the connections described.
PLEASE NOTE!
The devices listed are not necessarily supplied! The connections listed are optional and are not necessarily present on
your PC.
5.1. Connecting the cables
Follow the instructions below to connect your PC correctly and safely:
Position the cable so that it cannot be stepped on or tripped over.
To avoid damaging the cable, do not place any objects on it.
Do not expose plug connections to impacts/pressure, e.g. from lateral forces. This could cause internal and external dam-
age to the device.
Do not apply force when connecting cables and plugs and make sure that connectors are the right way round.
When you disconnect a cable from your device, pull it out by holding the plug and not the cable.
In order to prevent short-circuits and cable breaks, do not crush or bend cables.
Connect peripheral devices, such as keyboards, mouse and monitor, etc., only when the PC is switched off to avoid damage
to the PC or the devices. Some devices may also be connected while the PC is running.
This is often the case for USB devices. In all cases, ensure that the information provided in the relevant operating instruc-
tions is observed.
Maintain a distance of at least one metre from sources of high-frequency and magnetic interference (TV sets, loudspeak-
ers, mobile phones, DECT telephones, etc.) in order to avoid malfunctions and data loss.
Please note that only shielded cables that are shorter than 3 metres may be connected to the external interfaces of this PC.
Please only use double-shielded cables for printer cable connections.
Do not exchange the supplied cable for another one. Use only the supplied cable as this cable has been extensively tested
in our laboratory.
When connecting your periphery devices, also ensure that you only use the connection cables supplied with those devic-
es.
Ensure that all connection cables are connected to their corresponding periphery device to avoid any interference radia-
tion. Disconnect any cables that are not required.
The only devices which may be connected to the PC are those which meet the requirements set out in the EN60950 stand-
ard “Information Technology Equipment – Safety or the EN60065 standard Audio, video and similar electronic apparatus –
Safety requirements.
During the first few hours of use, new products may give off a characteristic but totally harmless smell. This is unavoidable
and disappears over time.
To help reduce the amount of odour build-up, we recommend that you ventilate the room at regular intervals. We have
taken appropriate measures during the development of this product to ensure that levels are well below legal limits.
PLEASE NOTE!
The devices listed are not necessarily supplied. You only need to connect those components you intend to operate on
your PC. If you do not have the device described, you can skip the point in question or carry it out later, as required.
5.2. Opening and closing the front panel (optional)
Some connections are located behind the front panel. This offers the advantage of making it quick and easy to connect fre-
quently used devices without having to turn the PC around. The closable panel also protects the connections.
5.3. Connecting the m icrophone (optional)
Connect a microphone to the pink socket using a 3.5 mm mono jack plug.
Position the microphone so that it does not point directly at the speakers. This prevents acoustic feedback (perceptible by
a loud whistling).
9 of 36
5.4. Connecting SATA devices (optional)
eSATA stands for external Serial ATA and is a connection for external hard drives. Compared with the conventional USB
standard, the transfer speed with an eSATA connection is higher than with external USB hard drives.
PLEASE NOTE!
In order to prevent damage to the contacts, make sure that the plug and the socket fit together perfectly. Due to its
asymmetric form, the plug will only fit into the socket in one position.
Plug the cable into the eSATA socket on the front of your PC.
5.4.1. Disconnecting SATA Devices
Before disconnecting a SATA hard drive from your PC, click the Safely remove hardware icon in the task bar below and
then click on the hard drive to be removed.
5.5. Connecting USB devices (optional)
ATTENTION!
Do not connect your USB devices until you have finished the initial setup of your new PC. This will prevent any unneces-
sary interference during the installation. These devices can generally be connected while the PC is running. Please refer to
the operating manual for your peripheral device.
The PC’s USB voltage outputs are protected by a fuse (limited power source in accordance with EN60950). This ensures that
peripheral devices connected using the sockets in question cannot be damaged in the event of a technical fault with the
PC.
You will usually have several connection sockets available that you can use as desired.
PLEASE NOTE!
In order to prevent damage to the contacts, make sure that the plug and the socket fit together perfectly. Due to its
asymmetric form, the plug will only fit into the socket in one position.
Plug the device (printer, scanner, camera, etc.) into the appropriate socket.
PLEASE NOTE!
Where possible, always connect your devices to the same port that they were originally installed on. Otherwise they will
be assigned a new ID and the drivers will need to be reinstalled.
10 of 36
5.6. O verclocking button (optional)
Your computer is delivered with an application that enables you to overclock the processor. This is useful if you want higher
performance for certain applications, such as video editing or games.
Depending on your computer model, you enable overclocking…
using the button in the MEDION® ERAZER® Control Center,
using the OC switch on the computer’s front cover or
using the OC switch on the back of the computer.
Regardless of how you enable or disable overclocking, you will always need to restart your computer. When you launch the
MEDION® ERAZER® Control Center, a corresponding notification will appear.
ATTENTION!
Back up your data on external storage media after each update or change. We do not accept any liability for claims for
compensation arising from loss of data or any consequential loss or damage.
5.6.1. Processor overclocking using the button in the MEDION® ERAZER® Control Center
Launch the MEDION® ERAZER® Control Center by double-clicking the desktop shortcut.
User Account Control will inform you that changes are being made to your computer. Confirm the query with Yes. You will
see the programs main page with some information regarding your computer.
Open the OC Genie tab.
Click the OC Genie button to enable overclocking. A message prompts you to restart your computer.
PLEASE NOTE!
Your computer may be fitted with an OC switch on the front cover or on the back. If so, then this button has a purely in-
formational purpose. Disable indicates that overclocking is disabled; if the button shows Enable, overclocking is ena-
bled.
To disable overclocking, click the Enable button and restart your computer.
5.6.2. Processor overclocking using the OC switch on the front cover
If your computer has an OC switch on its front cover, you simply need to press the switch in order to overclock the processor
(the switch should click into position).
Restart your computer for the change to take effect. If you have launched the MEDION® ERAZER® Control Center, a corre-
sponding notification will appear on the screen.
To disable overclocking, press the switch again and restart your computer.
5.6.3. Processor overclocking using the OC switch on the back of the computer
If an OC switch is fitted on the back of your computer, you simply need to press the switch in order to overclock the processor
(the switch should click into position).
Restart your computer for the change to take effect. If you have launched the MEDION® ERAZER® Control Center, a corre-
sponding notification will appear on the screen.
To disable overclocking, press the switch again and restart your computer.
5.6.4. Making settings in the MEDION® ERAZER® Control Center
After activating processor overclocking, you can make a number of settings using the MEDION® ERAZER® Control Center.
For example, you can regulate the overclocking using the settings under CPU
Ratio. After making a change, you will need to restart your computer.
PLEASE NOTE!
A warning will appear if you make settings that are not supported by your computer.
The MEDION® ERAZER® Control Center is also a monitoring tool that shows you information about the motherboard, memory
and processor. The data provided is purely for information purposes and cannot be changed.
11 of 36
5.7. Connecting a monitor (optional)
Your PC is equipped with a VGA and/or a DVI connection.
PLEASE NOTE!
If your monitor has multiple inputs (e.g. VGA and DVI), only ever connect one data cable at a time (to prevent signal
mapping problems).
To prevent damage to the contacts, ensure that the plug and socket fit together exactly. Due to its asymmetric shape, the
plug will only fit into the socket in one position.
Connect your monitor’s data cable to the graphics connection on your PC. Remove the white protective ring (if present) on
the monitor plug.
Tighten the screws hand tight when connecting a VGA or DVI device to the monitor cable.
5.8. Connecting devices using the mini-HDMI socket (optional)
HDMI is an abbreviation for “High Definition Multimedia Interface, which is an interface for the fully digital transfer of audio
and video data.
You can connect output devices to this socket if they have a corresponding connection.
5.9. Connecting a HDMI device (optional)
HDMI is an abbreviation for “High Definition Multimedia Interface, which is an interface for the fully digital transfer of audio
and video data.
You can connect a TV, monitor or projector to this socket if it has a corresponding connection.
5.10. Connecting audio output / headphones /
speakers
Connect active loudspeakers here for playback or an audio connection cable for recording. Read the operating instructions for
your stereo system to see which input you need to use (usually Line in or Aux).
Plug the cable into the green socket on the back of the PC using the 3.5 mm stereo jack plug.
5.10.1. Connecting headphones
Connect headphones/earphones here.
Plug the cable into the green socket on your PC using the 3.5 mm stereo jack plug.
WARNING!
Excessive volume when using headphones or earphones can damage your hearing. Before pressing play, set
the volume to the lowest setting. Start playback and increase the volume to a comfortable level. Changing
the basic settings of the equaliser can also increase the volume and thus cause permanent damage to your
hearing. Changing the drivers, software, equaliser, operating system, etc., can also lead to an increase in the
volume and thus cause permanent damage to your hearing.
Listening to a device at high volumes for an extended period via headphones/earphones can damage your
hearing.
5.10.2. PCs with surround sound (optional)
Connect a surround sound system as follows:
Plug the cable for the front speaker into the green socket labelled FS.
Connect the speakers for the rear sound to the RS connection.
Connect a central speaker or a subwoofer to the CS socket.
Connect additional speakers for the rear sound area to the SS socket.
A digital audio output (SPDIF) (optional) may be connected using an optical or coaxial cable.
Plug an optical cable into the optical socket or a coaxial cable into the coaxial socket.
Connect the other end of the cable to an audio device with a corresponding digital input.
5.11. Connecting PS/2 devices (optional)
If you wish to connect a USB mouse or USB keyboard, then connection of a PS/2 mouse or keyboard is not necessary.
Connect the mouse cable to the green PS/2 port.
Connect the keyboard cable to the blue PS/2 port.
12 of 36
5.12. Connecting IEEE 1394 (FireWire) devices (optional)
ATTENTION!
Do not connect your IEEE 1394 devices until you have finished the initial setup of your new PC. This will prevent any un-
necessary interference during the installation. These devices can generally be connected while the PC is running. Please
refer to the operating manual for your peripheral device.
The PC’s IEEE 1394 voltage outputs are protected by a fuse (limited power source in accordance with EN60950). This en-
sures that peripheral devices connected using the sockets in question cannot be damaged in the event of a technical fault
with the PC.
PLEASE NOTE!
In order to prevent damage to the contacts, make sure that the plug and the socket fit together perfectly. Due to its
asymmetric form, the plug will only fit into the socket in one position.
Connect the IEEE 1394 cable to your PC’s IEEE 1394 port.
5.13. Connecting a n etwork (LAN)
You can prepare your PC for network operation using the network socket.
A network cable usually has two RJ45 plugs meaning it does not matter which end is plugged into which socket.
Plug one end of the network cable into the PC socket.
Connect the other end to another PC or a hub/switch.
For more information see the chapter Network Operation”.
5.14. Aerial socket for TV reception (optional)
5.15. Analogue TV reception
Connect the TV socket on your TV card to your terrestrial aerial or cable TV.
5.16. DVB-T TV reception
Where DVB-T and digital services are offered locally, you can make use of these services by connecting an appropriate aerial
(not supplied).
Connect a DVB-T aerial to the TV socket on your TV card.
5.17. DVB-S TV reception
You can watch television from your digital satellite system via the DVB-S socket.
Connect your satellite system to the TV socket on your TV card.
5.18. Connecting audio input/recording source
This socket is used to connect external analogue audio sources (e.g. stereo system, synthesizer).
Plug the connection cable into the light blue socket using the 3.5 mm stereo jack plug.
5.19. Connecting power supply
Finally, connect the power supply for your PC and the monitor.
Plug the power cable into the socket and connect it to your PC’s mains cable socket.
Please note the following safety advice:
DANGER!
Even when the mains switch is off, some components of the device are live. In order to disconnect the power to
your PC or to completely isolate the device from voltage sources, remove the mains plug from the mains
socket.
The socket must be close to the PC and easy to access.
Only operate the PC on earthed socket outlets of the household electricity network.
Only use the mains connection cable supplied.
For extra safety, we recommend using an overvoltage protection device to prevent your PC from sustaining damage as a
result of power surge s or lightning strikes.
The standard PC mains adapter has an on/off switch. This can be used to turn the PC on or off. When the switch is at OFF
(0), no power is being consumed.
Do not start up your PC yet!
First read the next chapter for some helpful tips on initial operation.
13 of 36
6. First use
The operating system and all hardware drivers are already preinstalled. You do not need to run any of the discs supplied.
For some programs (e.g. telephone CDs or encyclopaedias, it may be necessary to insert the relevant disc in order to call up
the data saved on it. Where this is the case, the software will prompt you to do this.
Once all connections have been established and all necessary connections have been screwed tight, you can start up your PC:
6.1. Starting up the PC
Switch the monitor on.
Switch on the mains switch by moving it to position I. (Set this switch to 0 to disconnect the power supply).
Press the On/Off switch once to turn on your PC.
Your PC will now start up and run through the various startup steps.
PLEASE NOTE!
There should be no bootable disk (e.g. the recovery disc) in the optical drive as this will prevent the operating system
from being loaded from the hard drive.
The operating system is loaded from the hard drive. The loading process takes a little longer during the initial setup. Once all
the necessary data has been entered, the operating system will be set up. The operating system is fully loaded once the Win-
dows® 8 startup screen appears.
NOTE!
The initial installation may take a few minutes. Do not unplug the PC from the mains or switch it off during the initial in-
stallation. This may adversely affect the installation. Do not switch the PC off until after the installation has been com-
pleted successfully and the startup screen appears.
Follow the instructions on the screen. Step-by-step instructions will guide you through the process to be followed.
The welcome procedure takes you through several screens and dialogues.
Select your desired language and then the desired country.
Licence agreement
Please read through the licence agreement carefully. It provides important legal information about the use of your software
product. To view the text in full, you must slide the scroll bar downwards using the mouse until you reach the end of the doc-
ument. You accept the licence agreement by checking the I accept the agreement radio button. Only this entitles you to use
the product in accordance with the terms and conditions.
After entering a computer name, you can connect your PC to the Internet immediately on the Wireless page (if you already
have a WLAN system installed or have an access point).
If you choose to skip this point, you can connect to the Internet later via the Windows® 8 interface.
If you have already set up an Internet connection, you can now log in to your PC using a Microsoft account.
The Microsoft Store allows you to purchase new apps or update previously installed apps.
If you log in on a local account, you can set up a Microsoft account later at any time.
The following animated windows simply contain information about using the new Windows® 8 operating system.
No entries of any kind may be made during the animation.
The Windows® 8 interface appears after the login process.
PLEASE NOTE!
In the first few days following the initial installation, Windows may update and configure data (e.g. with new updates)
which can result in delays in the PC shutting down and starting up. For this reason, do not switch the PC off prematurely.
This may adversely affect the installation.
14 of 36
7. The mouse
In addition to the two buttons, the mouse also has a wheel. Turn or press the wheel to scroll through documents or Internet
pages.
PLEASE NOTE!
The wheel can also be used as a button. The assignment depends on the application in question. In Word, for exam-
ple, the cursor changes shape and the screen display scrolls up or down in the appropriate direction when the mouse is
moved.
If the mouse pointer cannot be moved smoothly across the screen, please try using a different surface (mouse pad). Glass or
metal surfaces may prove problematic.
8. The keyboard
This section contains useful information about using the keyboard.
8.1. The Alt, Alt Gr and Ctrl buttons
The Alt key is used in combination with other keys to perform particular functions. These functions are determined by the
program being used. To enter a keyboard shortcut with the Alt key, press and hold down the Alt key while you press the oth-
er key. The Alt Gr key works in a similar way to the Alt key, but is used to obtain special characters. The Ctrl key (Control) per-
forms program functions in the same fashion as the Alt key. Useful keyboard shortcuts (dependent on software):
Keyboard shortcut Function and description
Alt + F4 Usually exits the selected program or closes the open window.
Alt + Print Copies an image of the currently selected window to the Clipboard.
Alt Gr + ß The backslash ( \ ) is produced.
Alt Gr + E The euro symbol is produced.
Alt Gr + Q Produces an @ as required for e-mails.
Ctrl + Alt + Delete Starts the Windows Security dialogue.
(Country-specific deviations are possible)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Medion X51 Operating instructions

Category
Mini PCs
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI