DeWalt DCS373-XE User manual
- Category
- Circular saws
- Type
- User manual
This manual is also suitable for
DCS373-XE
18V 140 mm (5-1/2") CORDLESS METAL-CUTTING CIRCULAR SAW
INSTRUCTION MANUAL
1
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: indicates a practice not related to personal injury which, if
not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ).
Technical Data
DCS373-XE
Voltage V 18
Power Input W 460
No-load/rated speed min
-1
3700
Blade diameter mm 140
Maximum depth of cut mm 43
Blade bore mm 20
Weight (without battery pack) kg 3,76
L
PA
(sound pressure) dB(A)
78
K
PA
(sound pressure uncertainty) dB(A)
3
L
WA
(sound power) dB(A)
89
K
WA
(sound power uncertainty) dB(A)
3
Vibration total values (triax vector sum) determined according to EN 60745:
Vibration emission value a
h
metal cutting
a
h,M
=
m/s²
3,1
Uncertainty K = m/s²
1,5
The vibration emission level given in this information sheet has been measured in
accordance with a standardised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure.
WARNING: The declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account
the times when the tool is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the effects of
vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
SAFETY INSTRUCTIONS FOR POWER TOOLS
When using power tools, always observe the safety regulations applicable in your
country to reduce the risk of fire, electric shock and personal injury. Read the following
safety instructions before attempting to operate this product. Keep these instructions in
a safe place.
WARNING: To reduce the risk of injury, user must read the instruction manual.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious
injury.
2
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
3
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc., in accordance with
these instructions, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
Electrical Safety
The electric motor has been designed for one voltage range only. Always check that
the power supply corresponds to the voltage on the rating plate. 220–240 V AC
means your tool will operate on alternating current. Operation at a voltage outside this
range can cause loss of power and can result in overheating. All DEWALT tools are
factory tested; if this tool does not operate, check the power supply. Your DEWALT
tool is double insulated, therefore no earth wire is required.
• Young children and the infirm. This appliance is not intended for use by young
children or infirm persons without supervision.
– This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
– Children should be supervised to ensure that they do not play with the appliance.
• Replacement of the supply cord. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or an authorised DEWALT Service Centre in
order to avoid a hazard.
Extension Cords
CAUTION: Use only extension cords that are approved by the country’s Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
Safety Instructions for All Saws
a) DANGER: Keep hands away from cutting area and the blade. Keep
your second hand on auxiliary handle, or motor housing. If both hands are
holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot protect you from
the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpiece. Less than a full
tooth of the blade teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands or across your leg. Secure the
workpiece to a stable platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of control.
e) Hold power tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring. Contact with
a “live” wire will also make exposed metal parts of the power tool “live” and
shock the operator.
f) When ripping always use a rip fence or straight edge guide. This improves
the accuracy of cut and reduces the chance of blade binding.
4
d) Support large panels to minimize the risk of blade pinching and kickback.
Large panels tend to sag under their own weight. Supports must be placed
under the panel on both sides, near the line of cut and near the edge of the
panel.
e) Do not use dull or damaged blades. Unsharpened or improperly set blades
produce narrow kerf causing excessive friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking levers must be tight and secure
before making cut. If blade adjustment shifts while cutting, it may cause
binding and kickback.
g) Use extra caution when sawing into existing walls or other blind areas. The
protruding blade may cut objects that can cause kickback.
LOWER GUARD SAFETY INSTRUCTIONS
a) Check lower guard for proper closing before each use. Do not operate the
saw if lower guard does not move freely and close instantly. Never clamp
or tie the lower guard into the open position. If saw is accidentally dropped,
lower guard may be bent. Raise the lower guard with the retracting handle and
make sure it moves freely and does not touch the blade or any other part, in
all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard and the spring
are not operating properly, they must be serviced before use. Lower guard
may operate sluggishly due to damaged parts, gummy deposits, or a build-up
of debris.
c) Lower guard should be retracted manually only for special cuts such as
“plunge cuts” and “compound cuts.” Raise lower guard by retracting
handle and as soon as blade enters the material, the lower guard must be
released. For all other sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the blade before placing
saw down on bench or floor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path. Be aware of the time it
takes for the blade to stop after switch is released.
NOTE: Although the above information references wood, this saw is only to be used
to cut metal. Kickback can occur when cutting metal.
g) Always use blades with correct size and shape (diamond versus round) of
arbor holes. Blades that do not match the mounting hardware of the saw will
run eccentrically, causing loss of control.
h) Never use damaged or incorrect blade washers or bolt. The blade washers
and bolt were specially designed for your saw, for optimum performance and
safety of operation.
Further Safety Instructions for All Saws
CAUSES AND OPERATOR PREVENTION OF KICKBACK:
• Kickback is a sudden reaction to a pinched, bound or misaligned saw blade,
causing an uncontrolled saw to lift up and out of the workpiece toward the
operator;
• When the blade is pinched or bound tightly by the kerf closing down, the blade
stalls and the motor reaction drives the unit rapidly back toward the operator;
• If the blade becomes twisted or misaligned in the cut, the teeth at the back edge
of the blade can dig into the top surface of the wood causing the blade to climb
out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below:
a) Maintain a firm grip with both hands on the saw and position your arms to
resist kickback forces. Position your body to either side of the blade, but
not in line with the blade. Kickback could cause the saw to jump backwards,
but kickback forces can be controlled by the operator, if proper precautions
are taken.
b) When blade is binding, or when interrupting a cut for any reason, release
the trigger and hold the saw motionless in the material until the blade
comes to a complete stop. Never attempt to remove the saw from the work
or pull the saw backward while the blade is in motion or kickback may
occur. Investigate and take corrective actions to eliminate the cause of blade
binding.
c) When restarting a saw in the workpiece, center the saw blade in the kerf
and check that saw teeth are not engaged into the material. If saw blade
is binding, it may walk up or kickback from the workpiece as the saw is
restarted.
5
Additional Specific Safety Instructions for Circular Saws
WARNING: Do not use abrasive wheels or blades.
WARNING: Do not use water feed attachments.
CAUTION: Do not attempt to cut stainless steel, rebar, hardened or heat-treated
steel, cast iron, masonry or unknown materials
• Use clamps or another practical way to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
• Keep your body positioned to either side of the blade, but not in line with the
saw blade. KICKBACK could cause the saw to jump backwards (see Causes and
Operator Prevention of Kickback and KICKBACK).
• Air vents often cover moving parts and should be avoided. Loose clothes,
jewelry or long hair can be caught in moving parts.
WARNING: We recommend the use of a residual current device with a residual
current rating of 30mA or less.
WARNING: ALWAYS wear approved protective safety equipment complying with
the following standards:
• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;
• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;
• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use AS/NZS1716 approved
respiratory protection appropriate for the dust exposure. Direct particles away from
face and body.
WARNING: Always wear proper personal hearing protection that conforms to
AS/NZS1270 during use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V ......................volts A .........................amperes
Hz ....................hertz W ........................watts
min ..................minutes or AC ............alternating current
or DC .....direct current or AC/DC ......alternating or
...................Class I Construction direct current
(grounded) no .......................no load speed
...................Class II Construction n .........................rated speed
(double insulated) .......................earthing terminal
…/min .............per minute .......................safety alert symbol
BPM .................beats per minute IPM .....................impacts per minute
RPM .................revolutions per minute SPM ....................strokes per minute
sfpm ................surface feet per minute
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include the catalog number and
voltage. Consult the chart at the end of this manual for compatibility of chargers and
battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack
and charger, read the safety instructions below and then follow charging procedures
outlined.
READ ALL INSTRUCTIONS
6
• Do not charge or use the battery pack in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Inserting or removing the
battery pack from the charger may ignite the dust or fumes.
• NEVER force the battery pack into the charger. Do not modify the battery pack
in any way to fit into a non-compatible charger as battery pack may rupture
causing serious personal injury. Consult the chart at the end of this manual for
compatibility of batteries and chargers.
• Charge the battery packs only in designated DEWALT chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the
temperature may reach or exceed 40 ˚C (105 ˚F) (such as outside sheds
or metal buildings in summer). For best life store battery packs in a cool, dry
location.
NOTE: Do not store the battery packs in a tool with the trigger switch locked
on. Never tape the trigger switch in the ON position.
WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If
the battery pack case is cracked or damaged, do not insert into the charger. Do not
crush, drop or damage the battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or damaged in any way (e.g.,
pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be
returned to the service center for recycling.
WARNING: Fire hazard. Do not store or carry the battery pack so that metal
objects can contact exposed battery terminals. For example, do not place the
battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries can possibly cause fires if the
battery terminals inadvertently come in contact with conductive materials such as
keys, coins, hand tools and the like. The US Department of Transportation Hazardous
Material Regulations (HMR) actually prohibits transporting batteries in commerce
or on airplanes (e.g., packed in suitcases and carry-on luggage) UNLESS they are
properly protected from short circuits. So when transporting individual battery packs,
make sure that the battery terminals are protected and well insulated from materials
that could contact them and cause a short circuit.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
• Do not incinerate the battery pack even if it is severely damaged or is
completely worn out. The battery pack can explode in a fire. Toxic fumes and
materials are created when lithium ion battery packs are burned.
• If battery contents come into contact with the skin, immediately wash area
with mild soap and water. If battery liquid gets into the eye, rinse water over the
open eye for 15 minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic carbonates and
lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh
air. If symptoms persist, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or
flame.
Important Safety Instructions for All Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating
instructions for battery chargers.
• Before using the charger, read all instructions and cautionary markings on the
charger, battery pack and product using the battery pack.
WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT
rechargeable battery packs. Other types of batteries may overheat and burst resulting
in personal injury and property damage.
NOTICE: Under certain conditions, with the charger plugged into the power supply, the
charger can be shorted by foreign material. Foreign materials of a conductive nature,
such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from the charger cavities. Always
unplug the charger from the power supply when there is no battery pack in the cavity.
Unplug the charger before attempting to clean.
• DO NOT attempt to charge the battery pack with any chargers other than the
ones in this manual. The charger and battery pack are specifically designed to
work together.
• These chargers are not intended for any uses other than charging DEWALT
rechargeable batteries. Any other uses may result in risk of fire, electric shock
or electrocution.
• Do not expose the charger to rain or snow.
7
• Pull by the plug rather than the cord when disconnecting the charger. This will
reduce the risk of damage to the electric plug and cord.
• Make sure that the cord is located so that it will not be stepped on, tripped
over or otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use
of improper extension cord could result in risk of fire, electric shock or
electrocution.
• When operating a charger outdoors, always provide a dry location and use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
• Do not place any object on top of the charger or place the charger on a soft
surface that might block the ventilation slots and result in excessive internal
heat. Place the charger in a position away from any heat source. The charger is
ventilated through slots in the top and the bottom of the housing.
• Do not operate the charger with a damaged cord or plug.
• Do not operate the charger if it has received a sharp blow, been dropped or
otherwise damaged in any way. Take it to an authorized service center.
• Do not disassemble the charger; take it to an authorized service center when
service or repair is required. Incorrect reassembly may result in a risk of electric
shock, electrocution or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This
will reduce the risk of electric shock. Removing the battery pack will not reduce
this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard 230 V household electrical
power. Do not attempt to use it on any other voltage. This does not apply to the
vehicular charger.
Chargers
Your tool uses a DEWALT charger. Be sure to read all safety instructions before using
your charger. Consult the chart at the end of this manual for compatibility of chargers
and battery packs.
Charging Procedure (Fig. 1)
1. Plug the charger into an appropriate outlet before
FIG. 1
I
inserting the battery pack.
2. Insert the battery pack (I) into the charger, as
shown in Figure 1, making sure the pack is fully
seated in charger. The red (charging) light will
blink continuously, indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
Indicator Light Operation
PACK CHARGING
PACK CHARGED
x
HOT/COLD DELAY
PROBLEM PACK OR CHARGER
PROBLEM POWERLINE
Charge Indicators
This charger is designed to detect certain problems that can arise. Problems are indicated
by the red light flashing at a fast rate. If this occurs, re-insert the battery pack into the
charger. If the problem persists, try a different battery pack to determine if the charger
is working properly. If the new pack charges correctly, then the original pack is defective
and should be returned to a service center or other collection site for recycling. If the new
battery pack elicits the same trouble indication as the original, have the charger and the
battery pack tested at an authorized service center.
8
4. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights;
c. Move the charger and battery pack to a location where the surrounding air
temperature is approximately 18 ˚– 24 ˚C (65 ˚F and 75 ˚F);
d. If charging problems persist, take the tool, battery pack and charger to your
local service center.
5. The battery pack should be recharged when it fails to produce sufficient power
on jobs which were easily done previously. DO NOT CONTINUE to use under
these conditions. Follow the charging procedure. You may also charge a partially
used pack whenever you desire with no adverse effect on the battery pack.
6. Foreign materials of a conductive nature such as, but not limited to, grinding dust,
metal chips, steel wool, aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the charger from the power
supply when there is no battery pack in the cavity. Unplug the charger before
attempting to clean.
7. Do not freeze or immerse the charger in water or any other liquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside the charger. Electric
shock may result.
WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow
any liquid to enter the battery pack. Never attempt to open the battery pack for any
reason. If the plastic housing of the battery pack breaks or cracks, return to a service
center for recycling.
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct sunlight and
excess heat or cold.
2. For long storage, it is recommended to store a fully charged battery pack in a
cool dry place out of the charger for optimal results.
NOTE: Battery packs should not be stored completely depleted of charge. The battery
pack will need to be recharged before use.
HOT/COLD DELAY
This charger has a hot/cold delay feature: when the charger detects a battery that is
hot, it automatically starts a delay, suspending charging until the battery has cooled.
After the battery has cooled, the charger automatically switches to the pack charging
mode. This feature ensures maximum battery life. The red light flashes long, then
short while in the hot/cold delay mode.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge indicator showing
Pack Charged.
WEAK BATTERY PACKS: Weak batteries will continue to function but should not be
expected to perform as much work.
FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack. The
charger will indicate faulty battery pack by refusing to light or by displaying problem pack
or charger.
NOTE: This could also mean a problem with a charger.
PROBLEM POWER LINE
Some chargers have a Problem Powerline indicator. When the charger is used with
some portable power sources such as generators or sources that convert DC to AC,
the charger may temporarily suspend operation, flashing the red light with two fast
blinks followed by a pause. This indicates the power source is out of limits.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 18 ° – 24 °C (65 °F and 75 °F). DO NOT
charge the battery pack in an air temperature below +4 °C (+40 °F), or above
+40 °C (+105 °F). This is important and will prevent serious damage to the
battery pack.
2. The charger and battery pack may become warm to the touch while charging.
This is a normal condition, and does not indicate a problem. To facilitate the
cooling of the battery pack after use, avoid placing the charger or battery pack in
a warm environment such as in a metal shed or an uninsulated trailer.
3. A cold battery pack will charge at about half the rate of a warm battery pack. The
battery pack will charge at that slower rate throughout the entire charging cycle
and will not return to maximum charge rate even if the battery pack warms.
9
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
COMPONENTS (FIG. 2)
WARNING: Never modify the power tool or any part of it. Damage or personal
injury could result.
A. Trigger switch K. Shoe
B. Trigger switch lock-off button L. Blade wrench
C. Depth adjustment lever M. Battery release buttons
D. Blade lock button N. Main handle
E. Kerf indicator O. Auxiliary handle
F. Blade clamping screw P. Fuel gauge button
G. Lower guard Q. Inner clamp washer
H. Lower guard retracting lever R. Outer clamp washer
I. Battery pack S. Saw spindle
J. Sight window T. Blade
INTENDED USE
This metal-cutting circular saw is intended for use by professionals for cutting light
gauge metals and small metal structural shapes.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
This metal-cutting circular saw is a professional power tool. DO NOT let children
come into contact with the tool. Supervision is required when inexperienced operators
use this tool.
WARNING: Do not plunge cut or pocket cut with this saw.
FIG. 2
A
B
C
E
D
L
F
H
I
G
J
K
M
D
E
ON
10
Window (Fig. 2)
WARNING: Do not operate the saw with a damaged or missing sight window.
If window is damaged or missing, have the saw serviced at an authorized service
center. If saw is operated without the window, metal chips could fly through the guard
and cause personal injury.
CAUTION: Do not use oil or cutting fluids with the metal-cutting saw. Do not use
cleaning fluids to clean the window. Cleaning fluids, cutting fluids or oils could harm
the plastic in the window, interfering with the safe operation of the saw.
The saw is equipped with a sight window (J) on the side of the upper guard. This
window allows the user to see a cutting line on the material to be cut.
Saw Shoe (Fig. 2)
The front of the saw shoe (K) has a kerf indicator (E) that allows the operator to glide
the saw along cutting lines. Aligning the cutting line with the notch on the front of the
shoe and centering it using the modified V-shaped kerf indicator allows the operator
to keep the blade in line with the cutting line. If the cutting line is visible through the
narrowest part of the kerf indicator, the blade will pass directly over the cutting line.
Worklight
The saw is equipped with a worklight that is activated when the trigger switch is
depressed. The light will automatically turn off 20 seconds after the trigger switch is
released. If the trigger switch remains depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate work surface and is not intended to
be used as a flashlight.
OPERATION
WARNING: To reduce the risk of injury, turn unit off and disconnect it from
power source before installing and removing accessories, before adjusting or
when making repairs. An accidental start-up can cause injury.
Installing and Removing the Battery Pack (Fig. 3)
NOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack (I) into the tool handle, align the battery pack with the rails
inside the tool’s handle and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release button (M) and firmly pull
the battery pack out of the tool handle. Insert it into the charger as described in the
charger section of this manual.
I
FIG. 3
M
P
FIG. 3A
Fuel Gauge Battery Packs (Fig. 3A)
Some DEWALT battery packs include a fuel gauge which consists of three green LED
lights that indicate the level of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button (P). A combination
of the three green LED lights will illuminate designating the level of charge left. When
the level of charge in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left on the battery pack.
It does not indicate tool functionality and is subject to variation based on product
components, temperature and end-user application.
For more information regarding fuel gauge battery packs, please call 1800 338 002
(Aust) or 0800 339 258 (NZ).
Trigger Switch (Fig. 2)
The saw is controlled by a trigger switch (A) and lock off button (B). The lock off
button must be pressed before the trigger switch will turn the saw on. Releasing the
trigger turns the saw off.
11
NOTE: This tool has no provision to lock the switch on. The saw should never be
locked on by any means.
Changing Blades (Fig. 1, 4–6)
WARNING: To reduce the risk of injury, turn unit off and disconnect it from
power source before installing and removing accessories, before adjusting or when
making repairs. An accidental start-up can cause injury.
TO INSTALL THE BLADE
1. Place inner clamp washer
Q
FIG. 4
R
F
S
(Q) on saw spindle (S)
with the large flat surface
facing out toward the
blade (Fig. 4, 5).
2. Retract the lower blade
guard (G) and place blade
on saw spindle against
the inner clamp washer
(Q), making sure that
the blade will rotate in
the proper direction (the
direction of the rotation arrow on the saw blade and the teeth must point in the
same direction as the direction of rotation arrow on the saw). Do not assume
that the printing on the blade will always be facing you when properly installed.
When retracting the lower blade guard to install the blade, check the condition
and operation of the lower blade guard to assure that it is working properly. Make
sure it moves freely and does not touch the blade or any other part, in all angles
and depths of cut.
3. Place outer clamp washer (R) on saw spindle with the large flat surface against
the blade with beveled side facing out.
F
R
FIG. 5
Q
F
R
T
Q
S
12
4. Thread blade clamping screw (F) into
FIG. 6
D
TIGHTEN
(counterclockwise)
LOOSEN
(clockwise)
saw spindle by hand (screw has left-
hand threads and must be turned
counterclockwise to tighten) (Fig. 6).
5. Depress the blade lock button (D) while
turning the saw spindle with the blade
wrench (L, Fig. 1) until the blade lock
engages and the blade stops rotating.
6. Tighten the blade clamping screw firmly
with the blade wrench.
NOTICE: Never engage the blade lock while
saw is running, or engage in an effort to
stop the tool. Never turn the saw on while
the blade lock is engaged. Serious damage
to your saw will result.
TO REPLACE THE BLADE
1. To loosen the blade clamping screw (F), depress the blade lock button (D) and
turn the saw spindle with the blade wrench until the blade lock engages and the
blade stops rotating. With the blade lock engaged, turn the blade clamping screw
clockwise with the blade wrench (screw has left-hand threads and must be
turned clockwise to loosen).
2. Remove the blade clamping screw (F) and outer clamp washer (R) only. Remove
old blade.
3. Clean any metal chips/shavings that may have accumulated in the guard or
clamp washer area and check the condition and operation of the lower blade
guard as previously outlined. Do not lubricate this area.
4. Select the proper blade for the application (see Blades). Always use blades that
are the correct size (diameter) with the proper size and shape center hole for
mounting on the saw spindle. Always assure that the maximum recommended
speed (rpm) on the saw blade meets or exceeds the speed (rpm) of the saw.
5. Follow steps 2 through 6 under To Install the Blade, making sure that the blade
will rotate in the proper direction.
LOWER BLADE GUARD
WARNING: Under certain conditions of use, metal chips may become imbedded
in the surfaces of the lower guard, causing the lower guard to rub against the upper
guard. Check the operation of the lower guard before each use and remove any
imbedded chips.
WARNING: The lower blade guard is a safety feature which reduces the risk
of serious personal injury. Never use the saw if the lower guard is missing,
damaged, misassembled or not working properly. Do not rely on the lower blade
guard to protect you under all circumstances. Your safety depends on following
all warnings and precautions as well as proper operation of the saw. Check lower
guard for proper closing before each use as outlined in Additional Safety Rules for
Circular Saws. If the lower blade guard is missing or not working properly, have
the saw serviced before using. To assure product safety and reliability, repair,
maintenance and adjustment should be performed by an authorized service center
or other qualified service organization, always using identical replacement parts.
Blades
WARNING: To minimize the risk of eye injury, always use eye protection. Carbide
is a hard but brittle material. Foreign objects in the workpiece such as wire or nails
can cause tips to crack or break. Only operate saw when proper saw blade guard is in
place. Mount blade securely in proper rotation before using, and always use a clean,
sharp blade.
Blade Diameter Teeth Application
DT1212-QZ 5-1/2" (140 mm) 30 General purpose ferrous metal
cutting
If you need assistance regarding blades, please call 1800 338 002 (Aust) or 0800
339 258 (NZ).
KICKBACK
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing
an uncontrolled saw to lift up and out of the workpiece toward the operator. When the
blade is pinched or bound tightly by the kerf closing down, the blade stalls and the
motor reaction drives the unit rapidly back toward the operator. If the blade becomes
twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into
the top surface of the material causing the blade to climb out of the kerf and jump
back toward the operator.
13
Kickback is more likely to occur when any of the following conditions exists.
1. IMPROPER WORKPIECE SUPPORT
A. Sagging or improper lifting of the cut off piece can cause pinching of the blade
and lead to kickback (Fig. 9).
B. Cutting through material supported at the outer ends only can cause kickback.
As the material weakens it sags, closing down the kerf and pinching the blade
(Fig. 9).
C. Cutting off a cantilevered or overhanging piece of material from the bottom up
in a vertical direction can cause kickback. The falling cut off piece can pinch
the blade.
D. Cutting off long narrow strips can cause kickback. The cut off strip can sag or
twist closing the kerf and pinching the blade.
E. Snagging the lower guard on a surface below the material being cut
momentarily reduces operator control. The saw can lift partially out of the cut
increasing the chance of blade twist.
2. IMPROPER DEPTH OF CUT SETTING ON SAW
To make the most efficient cut, the blade should protrude only far enough to
expose a tooth as shown in Figure 8. This allows the shoe to support the blade
and minimizes twisting and pinching in the material. See the section titled Cutting
Depth Adjustment.
3. BLADE TWISTING (MISALIGNMENT IN CUT)
A. Pushing harder to cut can cause the blade to twist.
B. Trying to turn the saw in the cut (trying to get back on the marked line) can
cause blade twist.
C. Overreaching or operating the saw with poor body control (out of balance),
can result in twisting the blade.
D. Changing hand grip or body position while cutting can result in blade twist.
E. Backing up the saw to clear blade can lead to twist.
4. USE OF DULL OR DIRTY BLADES
Dull blades cause increased loading of the saw. To compensate, an operator will
usually push harder which further loads the unit and promotes twisting of the
blade in the kerf. Worn blades may also have insufficient body clearance which
increases the chance of binding and increased loading.
5. RESTARTING A CUT WITH THE BLADE TEETH JAMMED AGAINST THE
MATERIAL
The saw should be brought up to full operating speed before starting a cut or
restarting a cut after the unit has been stopped with the blade in the kerf. Failure to
do so can cause stalling and kickback.
Any other conditions which could result in pinching, binding, twisting, or misalignment
of the blade could cause kickback. Refer to the sections Further Safety Instructions
for All Saws and Blades for procedures and techniques that will minimize the
occurrence of kickback.
Depth Adjustment (Fig. 7, 8)
WARNING: To reduce the risk of injury, turn unit off and disconnect it from
power source before installing and removing accessories, before adjusting or
when making repairs. An accidental start-up can cause injury.
The metal-cutting saw is equipped with a pivoting shoe that allows the operator to
set the depth of cut. For the most efficient cutting action, set the depth adjustment so
that one tooth of the blade projects below the material to be cut. This distance is from
the tip of the tooth to the bottom of the gullet in front of the tooth. This keeps blade
friction at a minimum, removes metal chips from the cut, results in cooler, faster
sawing and reduces the chance of kickback.
FIG. 7
C
FIG. 8
14
TO SET THE DEPTH OF CUT
1. Lay the piece of material you plan to cut along the blade as shown.
2. Note how much tooth projects beyond the material.
3. Loosen the depth adjustment lever (C) and move the shoe to change the depth of
cut.
4. Retighten the depth adjustment lever securely.
Workpiece Support (Fig. 9)
CUTTING SHEETS OF METAL
Figure 9 shows the correct and incorrect way to support a large sheet. To avoid
kickback, support material near the cut. Do not support it away from the cut. If
material is supported away from the cut, it will bind the blade and cause kickback.
When cutting thin strips, keep the blade at least 1/2" (approximately 13 mm) from the
edge of the material. Thin strips may bind, causing kickback and increasing the risk of
personal injury.
FIG. 9
1/2"
(13 mm)
CUTTING RECTANGULAR METAL STOCK
Clamp the material you plan to cut to a workbench or other work surface as shown
above.
Cutting (Fig. 10, 11)
1. Hold the saw securely using both hands. Figure 10 shows appropriate hand
position. Keep your body to one side of the line along which you are cutting. This
will protect you from injury related to kickback.
2. When cutting ends off of rectangular
FIG. 10
metal stock, place the widest part of the
shoe on the part of the material that is
clamped to the workbench or other
support, not on the part of the material
that will fall when the cut is made.
3. Depress the trigger switch and allow the
saw to reach full speed before the blade
contacts the material to be cut (Fig. 11).
4. Push the saw forward at a speed that
allows the blade to cut without laboring.
5. As you finish a cut, release the trigger and allow the blade to stop before lifting
the saw from the work. As you lift the saw, the guard will automatically close
under the blade.
FIG. 11
CORRECTING A CUT
Should your cut begin to leave the cutting line, don’t try to force it back on. Forcing a
correction can stall the saw and cause kickback. Instead, release the switch and allow
the blade to come to a complete stop. Then, back the saw out of the cut. Restart the
saw and re-enter the cut, following the desired cutting line.
15
CAUTION: Do not cut through bolts with the metal-cutting saw. Damage to the saw
or personal injury could result.
Maximizing Blade Life
To extend blade life, follow these practices:
• Do not force the blade through the metal. The saw must cut at its own pace and
at a constant rate.
• Change blades when it is no longer easy to push the saw through the cut, when
the motor is straining, or when excessive heat is built up in the blade.
• Keep base of the saw firmly against metal you are cutting.
• If the metal you are cutting is vibrating or shaking, clamp the material as close to
the cut as possible and slow down the cutting rate.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from
power source before installing and removing accessories, before adjusting or
when making repairs. An accidental start-up can cause injury.
Replacing Sight Window (Fig. 1)
WARNING: Do not operate the saw with a damaged or missing sight window.
If window is damaged or missing, have the saw serviced at an authorized service
center. If the saw is operated without the window, metal chips could fly through the
guard and cause personal injury.
The sight window (J) must be replaced by an authorized DEWALT service center.
Lubrication
Self lubricating ball and roller bearings are used in the tool and relubrication is not
required. However, it is recommended that, once a year, you take or send the tool to a
certified service center for a thorough cleaning, inspection, and lubrication of the gear
case.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury, always wear AS/NZS1337 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-
metallic parts of the tool. These chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool into a liquid.
CAUTION: Do not use any cleaning fluids on the sight window to avoid clouding
it and compromising the safe operation of the saw. Use compressed air to remove
accumulated dust from the inside of the sight window. Wear safety glasses when
performing this.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC outlet before
cleaning. Dirt and grease may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any cleaning solutions.
Repairs
The charger and battery pack are not serviceable. There are no serviceable parts
inside the charger or battery pack.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by certified
service centers or other qualified service organizations, always using identical
replacement parts.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been
tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT, recommended accessories should be used
with this product.
Use only 5-1/2" (140 mm) DEWALT metal cutting blades with a 20 mm arbor.
Recommended accessories for use with your tool are available at extra cost from
your local service center. If you need any assistance in locating any accessory, please
contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call
1800 338 002 or (NZ) 0800 339 258.
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ)
www.dewalt.com.au • www.dewalt.co.nz
(JAN13) Part No. N201532 DCS373-XE Copyright © 2011, 2012, 2013 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;
the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
Battery Output Chargers/Charge Time
Nominal 230 Volts 12 Volts
X Indicates that the battery pack is not compatible with that specific charger.
All charge times are approximate. Actual charge time may vary.
Read the instruction manual for more specific information.
The battery voltage is nominal, it can measure above or below depending on the state of charge.
Cat. Number Voltage Amp Hour 97014 98014 DW9106 DW9107 DW9108 DW9115 DW9116 DW9117 DW9118 DE9116 DE9118 DW911 DC011 DW0245 DE2046 DC9000 DC9310 DCB100 DCB103 DCB105 DCB119 DW9109 DC9319
DC9360 36 2.2 X X X X X X X X X X X X X X X 60 X X X X X X X
DE0240-XJ 24 2.0 X X X X X X X X X X X X X 60 60 X X X X X X X X
DW0242 24 2.0 X X X X X X X X X X X X X 60 60 X X X X X X X X
DW0240 24 1.7 X X X X X X X X X X X X X 60 60 X X X X X X X X
DC9096 18 2.4 X X X X 60 X 60 20 X 60 X 60 60 X X X 60 X 60 X X 60 60
DC9180 18 2.0 X X X X X X X X X X X X X X X X 60 X 60 X X X 60
DCB180 18 3.0 X X X X X X X X X X X X X X X X X X 55 55 90 X X
DCB181 18 1.5 X X X X X X X X X X X X X X X X X X 30 30 40 X X
DCB182 18 4.0 X X X X X X X X X X X X X X X X X X 70 70 117 X X
DCB183 18 2.0 X X X X X X X X X X X X X X X X X X 40 40 60 X X
DW9096 18 2.4 X X X X 60 X 60 20 X 60 X 60 60 X X X 60 X 60 X X 60 60
DE9095-XJ 18 2.0 X X X X 60 X 60 20 X 60 X 60 60 X X X 60 X 60 X X 60 60
DC9091 14.4 2.4 60 60 60 60 60 15 60 15 60 60 60 60 60 X X X 60 X 60 X X 60 60
DC9144 14.4 2.0 X X X X X X X X X X X X X X X X 60 X 60 X X X 60
DCB141 14.4 1.5 X X X X X X X X X X X X X X X X X X 30 30 40 X X
DCB142 14.4 4.0 X X X X X X X X X X X X X X X X X X 90 90 117 X X
DCB143 14.4 2.0 X X X X X X X X X X X X X X X X X X 40 40 60 X X
DE9094 14.4 1.3 45 45 45 30 30 15 30 12 60 30 60 30 30 X X X 30 X 30 X X 30 30
DE9091-XJ 14.4 2.0 45 45 45 45 45 15 45 15 90 45 90 45 45 X X X 45 X 45 X X 45 45
DW9091 14.4 1.7 45 45 45 45 45 15 45 15 90 45 90 45 45 X X X 45 X 45 X X 45 45
DC9071 12 2.4 60 60 60 60 60 15 60 15 60 60 60 60 60 X X X 60 X 60 X X 60 60
DE9071-XJ 12 2.0 60 60 60 45 45 15 45 15 90 45 90 45 45 X X X 45 X 45 X X 45 45
DE9074-XJ 12 1.25 45 45 45 30 30 15 30 12 60 30 60 30 30 X X X 30 X 30 X X 30 30
DW9050 12 1.3 40 40 40 X X 15 X X X X X X X X X X X X X X X X X
DW9071 12 1.7 60 60 60 45 45 15 45 15 90 45 90 45 45 X X X 45 X 45 X X 45 45
DW9072 12 1.2 45 45 45 30 30 15 30 12 60 30 60 30 30 X X X 30 X 30 X X 30 30
DCB120 10.8 1.3 X X X X X X X X X X X X X X X X X 40 40 40 40 X X
DCB123 10.8 1.5 X X X X X X X X X X X X X X X X X 40 40 40 40 X X
DW9063 9.6 1.25 45 45 45 30 30 15 30 12 60 30 60 30 30 X X X 30 X 30 X X 30 30
DW9062 9.6 1.3 45 45 45 30 30 15 30 12 60 30 60 30 30 X X X 30 X 30 X X 30 30
DW9061 9.6 1.7 60 60 60 45 45 15 45 15 90 45 90 45 45 X X X 45 X 45 X X 45 45
DW9048 9.6 1.3 40 40 40 X X 15 X X X X X X X X X X X X X X X X X
DW9057 7.2 1.25 45 45 45 30 30 15 30 12 60 30 60 30 30 X X X 30 X 30 X X 30 30
DW9046 7.2 1.3 40 40 40 X X 15 X X X X X X X X X X X X X X X X X
DEWALT BATTERY AND CHARGER SYSTEMS
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
DeWalt DCS373-XE User manual
- Category
- Circular saws
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI