Denon POA-A1HDCI Quick start guide

Category
Audio amplifiers
Type
Quick start guide

Denon POA-A1HDCI is a fully configurable 10 channel power amplifier with THX Ultra2 certification, capable of delivering 150 watts per channel into 8 ohms and 300 watts per channel into 4 ohms. It features a mono block construction for each channel, ensuring consistent audio quality and performance. The amplifier utilizes a new circuit design that minimizes signal paths and employs direct mechanical grounding to reduce vibrations. It also boasts 8 individual transformers for a stable power supply and high current diodes and capacitors for driving bridged speakers.

Denon POA-A1HDCI is a fully configurable 10 channel power amplifier with THX Ultra2 certification, capable of delivering 150 watts per channel into 8 ohms and 300 watts per channel into 4 ohms. It features a mono block construction for each channel, ensuring consistent audio quality and performance. The amplifier utilizes a new circuit design that minimizes signal paths and employs direct mechanical grounding to reduce vibrations. It also boasts 8 individual transformers for a stable power supply and high current diodes and capacitors for driving bridged speakers.

POA-A1HDCI
10 ch Power Amplifier
New model information
THX Ultra2, Reference 150 Watts x 10 channel Fully Configurable
Power Amplifier
150W Mono Block Construction Amplifiers
Fully separated construction for each 10 channels for all same audio quality
Mono block concept to amplify with best performance
New amplifier circuit that shortens audio signal paths for the best audio
Direct Mechanical Ground to minimize mechanical vibration from
transformer and radiators
150W x 10 channels (8ohms), 300W (4ohms)
300W Bridgeable drive (8ohms), 500W (4 ohms)
THX Ultra2 certified
4 ohms guaranteed
High Current and Separated Power Supply
8 individual transformers to supply power to each discrete circuit
4 main power transformers to drive 10 ch power amplifiers with separated
coil winding for pure audio playback
High current diodes and capacitors to drive bridged speakers
Other Features
• RCA and XLR input for each channel
• VU meters available of any channel
• Gold plated wide pitch speaker terminal
• Bi-Amp / Bridge mode select
• Trigger input
• RS-232C
Denon Matching AV Control Center
• Link control with AVP-A1HDCI
Bullet points
16940707 A
Denon Brand Company
D&M Building, 2-1 Nisshin-cho, Kawasaki-ku, Kawasaki-shi,
Kanagawa, 210-8569, Japan
www.denon.com
Audio in (RCA)
Audio in (XLR)
10
10
Speaker A L/R out
Speaker B L/R out
10
10
IN
O
UT
Input / Output terminals
Specifications
Power Amplifier Section
Rated output 150 W (8 ohms) x 10 ch
300 W (4 ohms) x 10 ch
500 W (4 ohms, bridge)
General
Power supply AC 120 V, 60 Hz
Power consumption 12 A
(Standby : 0.3W)
D
imensions (WxHxD) 434 x 530 x 281 mm
1
7-3/32” x11-1/16” x 20-58/64”
Weight 60 kg, 132 lbs
Denon Electronics (USA), LLC
100 Corporate Drive
Mahwah, NJ 07430
www.usa.denon.com

L
ink Control in/out
R
S232C
T
rigger in
1 / 1
1
1
others
*Design and specifications are subject to change without notice.
*THX is a trademark of THX Ltd. THX may be registered in some jurisdiction. All rights reserved.
  • Page 1 1
  • Page 2 2

Denon POA-A1HDCI Quick start guide

Category
Audio amplifiers
Type
Quick start guide

Denon POA-A1HDCI is a fully configurable 10 channel power amplifier with THX Ultra2 certification, capable of delivering 150 watts per channel into 8 ohms and 300 watts per channel into 4 ohms. It features a mono block construction for each channel, ensuring consistent audio quality and performance. The amplifier utilizes a new circuit design that minimizes signal paths and employs direct mechanical grounding to reduce vibrations. It also boasts 8 individual transformers for a stable power supply and high current diodes and capacitors for driving bridged speakers.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI