Black & Decker HHVJ315JD10 User manual

INSTRUCTION MANUAL

CORDLESS HAND VACS

Thank you for choosing BLACK+DECKER!

PLEASE READ BEFORE RETURNING THIS PRODUCT FOR

ANY REASON.

If you have a question or experience a problem with your BLACK+DECKER

purchase, go to http://www.blackanddecker.com/instantanswers

If you can’t find the answer or do not have access to the Internet, call

1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri. to speak with an agent.

Please have the catalog number available when you call.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

VEA EL ESPANOL EN LA CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

CATALOG NUMBERS

HHVJ215JD

HHVJ315JD

HHVJ315JMF

To register your new product, call 1-800-544-6986

or visit www.BlackandDecker.com/NewOwner

2

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliances, basic

precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS

BEFORE USING THIS

APPLIANCE.

WARNING: Read all safety

warnings and all instructions. Failure to

follow the warnings and instructions listed

below may result in electric shock, fire and/

or serious injury.

WARNING: Some household dust

contains chemicals known to the State of

California to cause cancer, birth defects or

other reproductive harm such as asbestos

and lead in lead based paint.

WARNING: To reduce the risk of

fire, electrical shock or injury:

• WARNING: To reduce the risk of

electric shock – Do not

use outdoors or on wet surfaces.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

• Use only as described in this manual. Use only

manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If

appliance is not working as it should, has been

dropped, damaged, left outdoors, or dropped

into water, return it to a service center.

• Do not pull or carry by cord, use cord as

a handle, close a door on cord, or pull

cord around sharp edges or corners. Do

not run appliance over cord. Keep cord

away from heated surfaces.

• Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

• Do not handle charger, including charger

plug, and charger terminals with wet hands.

• Do not put any object into openings. Do

not use with any opening blocked; keep

free of dust,lint, hair, and anything that

may reduce air flow.

• Keep hair, loose clothing, fingers, and all

parts of body away from openings and

moving parts.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or

combustible liquids, such as gasoline, or

use in areas where they may be present.

• Do not pick up anything that is burning or

smoking, such as cigarettes, matches, or

hot ashes.

• Do not use without dust bag and/or filters

in place.

• Do not charge the unit outdoors.

• Use only the charger supplied by the

manufacturer to recharge.

• Do not incinerate the appliance even if it

is severely damaged. The batteries can

explode in a fire.

• This appliance is intended for household

use only and not for commercial or

industrial use.

• Shock Hazard. To protect against risk

of electrical shock, do not put unit or

charging base in water or other liquid.

• Do not allow the cord to hang over the edge

of a table or counter or touch hot surfaces.

The unit should be placed or mounted

away from sinks and hot surfaces.

• Plug the charger directly into an electrical

outlet.

• Use the charger only in a standard

electrical outlet (120V/60Hz).

• Unplug the charger from outlet before any

routine cleaning or maintenance.

• This product includes rechargeable nickel

cadmium batteries. Do not incinerate batteries

as they will explode at high temperatures.

• Leaks from battery cells can occur

under extreme conditions. If the liquid,

which is a 20-35% solution of potassium

hydroxide, gets on the skin (1) wash

quickly with soap and water or (2)

neutralize with a mild acid such as lemon

juice or vinegar. If the liquid gets into the

eyes, flush them immediately with clean

3

water for a minimum of 10 minutes. Seek

medical attention.

• Do not look into the air vents when the

unit is switched on, as sometimes

there is a possibility of small debris being

discharged from the air vents, especially

after cleaning / replacement of the filters

as debris inside the unit can be disturbed.

ADDITIONAL SAFETY

WARNINGS

a) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to battery pack, picking up

or carrying the appliance. Carrying the

appliance with your finger on the switch

or energizing appliance that have the

switch on invites accidents.

b) Recharge only with the charger

specified by the manufacturer. A

charger that is suitable for one type of

battery pack may create a risk of fire

when used with another battery pack.

c) Do not use a battery pack or appliance

that is damaged or modified. Damaged

or modified batteries may exhibit

unpredictable behavior resulting in fire,

explosion or risk of injury.

d) Do not expose a battery pack or

appliance to fire or excessive

temperature. Exposure to fire or

temperature above 266°F (130°C) may

cause explosion.

e) Have servicing performed by a qualified

repair person using only identical

replacement parts. This will ensure that

the safety of the product is maintained.

WARNING: Do not attempt to

modify or repair the appliance

SAVE THESE INSTRUCTIONS

Symbols

• The label on your tool may include the

following symbols. The symbols and their

definitions are as follows:

V ..................volts

A ..................amperes

Hz ................hertz

W .................watts

min ..............minutes

or AC ...... alternating current

or DC ..direct current

n

o ................no load speed

................Class I Construction

(grounded)

................earthing terminal

...............safety alert symbol

................Class II Construction

(double insulated)

.../min or rpm...revolutions or reciprocation

per minute

FUCTIONAL DESCRIPTION

1. On/off power button

2. Handle

3. Nozzle

4. Extendable crevice tool

5. Crevice tool release button

6. LED BATTERYSENSE

(SMARTECH vacuums only)

7. LED POWERBOOST indicator

8. Dust bowl

9. Dust bowl release button

10. Flip-up brush

11. FILTERSENSE LED

(SMARTECH vacuums only)

1

2

3

4

5

6

11

7

8

9

10

11

7

6

Charging the battery

WARNING: For use

only with the supplied charger.

From new, the rechargeable cells of the

product need a minimum charge time of 5

hours to ensure full power.

• Plug the jack plug of the charger into

the charging socket of the tool as shown

in Figure A. Plug the charger into any

standard 120 Volt 60 Hz electrical outlet.

The charging indicator will be lit.

4

A

While charging, the charger may get

warm, this is perfectly normal and safe. It

is safe to leave the appliance connected

to the charger indefinitely. The charger

automatically reduces power consumption

when charging is complete.

• When charging is complete, the LED will

turn off.

WARNING: Do not charge the

battery at ambient temperatures below

39°F (4°C) or above 104°F (40°C).

Switching on and off - Figure B

• To switch the appliance on, depress the

on/off button (1). The battery indicator

LED will illuminate and vacuum will begin

in the low-speed mode.

• Depress the button a second time to

engage the POWERBOOST mode. The

green LED will also illuminate, indicating

the vacuum is in the higher-speed mode.

• To switch the appliance off, depress the

button a third time.

B

POWERBOOST mode

The green LED will illuminate when the

appliance is in POWERBOOST mode. The

vacuum will operate at a higher suction level

to pick up debris that requires more power.

Filter sensor (HHVJ315JMF ONLY)

Whenever a lter is blocked and needs

cleaning, the red LED in the handle will

illuminate. Clean dust from lter (See

“Cleaning the Dust Bowl and Filter” section).

Nozzle / Accessories

• A crevice tool (4) is built into the nozzle

(3). Extend the crevice tool as shown in

Figure C, until it clicks in place.

• To shorten the crevice tool, depress the

crevice tool release button (5) as shown

in Figure D and slide the crevice tool into

the nozzle.

C

D

• A brush accessory is built into the nozzle

and can be flipped upwards for use as

shown in Figure E.

E

Dry pick up

• For everyday spills of dry material.

• Do not ll the dust bowl (8) beyond the

end of the intake chute.

Optimizing the suction force

In order to keep the suction force optimised,

the lters must be cleared regularly during use.

EMPTYING AND CLEANING

THE PRODUCT

Removing the dust bowl and

lters - Figures F & G

WARNING: The lters are reusable

and should be cleaned regularly.

• Press the dust bowl release button (9) as

shown in the insert of Figure F, then pull

the dust bowl (8) straight off as shown in

Figure F.

F

• While holding the dust bowl over a bin or

sink, pull out the lter (12) to empty the

contents as shown in Figure G.

G

12

• To replace the dust bowl, push it back onto

the appliance until it clicks rmly into place.

WARNING:

Never use the appliance

without the lters. Optimum dust collection

will only be achieved with clean lters.

Cleaning the dust bowl and lter

• The dust bowl and lter can be washed in

warm soapy water.

• Make sure the lter and the dust bowl are dry

before retting.

For a more thorough cleaning

• Remove the dust bowl and filter assembly

as described above.

• To separate the plastic filter (13) from the

cloth filter (14), twist the plastic filter in a

counterclockwise direction and lift it off of

the cloth filter as shown in Figure H.

• Shake or lightly brush any loose dust off

both filters.

H

13

14

• The dust bowls and filters can be washed

in warm soapy water. Allow to dry before

placing back into the vac.

• To replace the filters, slide the outer

plastic filter over the cloth filter.

• Align the wings of the plastic filter with

the slots in the cloth filter and twist in a

clockwise direction.

• Place filters back into the bowl pressing

firmly to ensure a secure fit.

• To replace dust bowl, place it back onto the

handle until it “clicks” firmly into position.

IMPORTANT: Maximum dust collection

will only be obtained with a clean filter and

an empty dust bowl. If dust begins to fall

back out of the product after it is switched

off, this indicates that the bowl is full and

requires emptying.

• Wash the filters regularly using warm, soapy

water and ensure that they are completely

dry before using again. The cleaner the filter

is, the better the product will perform.

• It is very important that the filter is

correctly in position before use.

Replacing the lters

The lters should be replaced every 6 to 9

months and whenever worn or damaged.

Replacement lters are available from your

BLACK+DECKER dealer.

Catalog numbers:

• Cloth lter: VBF10

MAINTENANCE

Use only mild soap and damp cloth to clean

the vac. Never let any liquid get inside the

vac; never immerse any part of the vac into

a liquid.

WARNING: Make sure the vacuum

is completely dry before using it.

IMPORTANT: To assure product SAFETY

and RELIABILITY, repairs, maintenance

and adjustment (other than those listed

in this manual) should be performed by

authorized service centers or other qualified

service organizations, always using identical

replacement parts.

5

6

The RBRC™ Seal

The RBRC® (Rechargeable

Battery Recycling Corp oration)

Seal on the lithium-ion batteries

(or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their

useful life have already been paid by

BLACK+DECKER. In some areas, it is

illegal to place spent lithium-ion batteries in

the trash or municipal solid waste stream

and the Call 2 Recycle® program provides

an environmentally conscious alternative.

Call 2 Recycle, Inc., in cooperation with

BLACK+DECKER and other battery

users, has established the program in the

United States and Canada to facilitate the

collection of spent lithium-ion batteries.

Help protect our environment and conserve

natural resources by returning the spent

nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

BLACK+DECKER service center or to

your local retailer for recycling. You may

also contact your local recycling center for

information on where to drop off the spent

battery. RBRC® is a registered trademark

of Call 2 Recycle, Inc.

Accessories

Recommended accessories for use with

your appliance are available from your local

dealer or authorized service center. If you

need assistance regarding accessories,

please call: 1-800-544-6986.

WARNING: The use of any

accessory not recommended for use with

this appliance could be hazardous.

This Class B digital apparatus complies

with Canadian ICES-003.

This device complies with part 15 of the

FCC rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

NOTE: This equipment has been tested

and found to comply with the limits for

a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits

are designed to provide reasonable

protection against harmful interference in

a residential installation. This equipment

generates, uses and can radiate radio

frequency energy and, if not installed and

used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in

a particular installation.

If this equipment does cause harmful

interference to radio or television

reception, which can be determined by

turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Changes or modifications to this unit

not expressly approved by the party

responsible for compliance could void the

user’s authority to operate the equipment.

This Class B digital apparatus complies

with Canadian ICES-003.

SERVICE INFORMATION

All BLACK+DECKER Service Centers

are staffed with trained personnel to

provide customers with efficient and

reliable power tool service. Whether you

need technical advice, repair, or genuine

factory replacement parts, contact the

BLACK+DECKER location nearest you. To

find your local service location, call: 1-800-

544-6986 or visit

www.blackanddecker.com

TWO-YEAR LIMITED

WARRANTY

Black & Decker (U.S.) Inc. warranties this

product to be free from defects in material

or workmanship for a period of two (2) years

following the date of purchase, provided that

the product is used in a home environment.

This limited warranty does not cover failures

due to abuse, accidental damage or when

repairs have been made or attempted by

anyone other than BLACK+DECKER and

its Authorized Service Centers. A defective

product meeting the warranty conditions set

forth herein will be replaced or repaired at

no charge in either of two ways:

The first, which will result in exchanges

only, is to return the product to the retailer

from whom it was purchased (provided

that the store is a participating retailer).

Returns should be made within the

time period of the retailer’s policy for

exchanges. Proof of purchase may be

required. Please check with the retailer

for its specific return policy regarding

time limits for returns or exchanges. The

second option is to take or send the product

(prepaid) to a BLACK+DECKER owned

or authorized Service Center for repair

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

7

or replacement at BLACK+DECKER’s

option. Proof of purchase may be required.

BLACK+DECKER owned and authorized

service centers are listed online at www.

blackanddecker.com.

This warranty does not apply to

accessories. This warranty gives you

specific legal rights and you may have

other rights which vary from state to state.

Should you have any questions, contact the

manager of your nearest BLACK+DECKER

Service Center. This product is not intended

for commercial use, and accordingly, such

commercial use of this product will void this

warranty. All other guarantees, express or

implied, are hereby disclaimed.

LATIN AMERICA:This warranty does not

apply to products sold in Latin America.

For products sold in Latin America, check

country specific warranty information

contained in the packaging, call the local

company or see the website for such

information.

FREE WARNING LABEL

REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-

544-6986 for a free replacement.

Page is loading ...

24

Cat. No. HHVJ215JD, HHVJ315JD, HHVJ315JMF Form No. 90632064

Copyright

©

2016 BLACK+DECKER Printed in

China January 2016

Black & Decker HHVJ315JD10 User manual

Black & Decker HHVJ315JD10 User manual

in other languages

Related papers

Other documents