Gas Hob
Model GC750TX
Instructions for Installation and Use
The Recipe Book
Hotpoint has come up with a small recipe book - which is practical, full of helpful tips and easy to use - to help you
rediscover the delights of cooking.
It contains a wide variety of handy tips to keep in mind to try out new dishes effortlessly.
It also has 15 recipes preprogrammed into the oven, so thanks to the interactive display, once you have done the
preparation all you have to do is make one simple selection.
kitchen think
To the Installer
Before installation fill in the product details on the back cover this book.
The information can be found on the rating plate.
To the User
You must read the instructions prior to installing and using the appliance and
then retain them for future reference.
2
CONTENTS
Introduction
For Your Safety
Know your Hob
How to use your Hob
Practical Advice
Care and Cleaning
Troubleshooting
Installation
Electrical Connection
Characteristics of Burners and Nozzels
After Sales Service
Guarantee
Key Contacts
3
4
5
5
6
7
7
8-10
11
12
13
14
Back Cover
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of
the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also
provided so the new owner can become familiar with the appliance and safety warnings.
If the Book is lost or damaged a copy may be obtained from:
Indesit Company UK LTD., Morley Way, Peterborough, PE2 9JB
3
Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been
installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The hob is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.
Introduction
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with this booklet.
(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the
appliance.
(c) Has not been subjected to misuse or accident or been modified or repaired by any person other than the
manufacturers authorised employee or agent.
(d) Has been correctly installed.
This appliance conforms with the following European Economic Community directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;
- 90/396/EEC of 29/06/90 (Gas) and subsequent modifications;
- 93/68/EEC of 22/07/93 and subsequent modifications.
- 2002/96/EC
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the
impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old
appliance.
4
For Your Safety
ALWAYS:
- make sure you remove all packaging and dispose of
safely.
- check the soundness of the appliance after it has been
unpacked.
- make sure you understand the controls before using the
appliance.
- keep children away from the appliance during use.
- take care to avoid heat/steam burns when operating the
controls.
- make sure the controls are turned off when you have
finished cooking and when not in use.
- take care to avoid heat/steam burns when operating the
controls.
- disconnect from the power supply, and allow to cool,
before cleaning or performing maintenance.
- refer servicing to a qualified appliance service engineer.
- keep the hob clean as a build up of grease or fat from
cooking can cause a fire.
- follow the basic principles of food handling and hygiene
to prevent the possibility of bacterial growth.
- dry food thoroughly before frying and lower it slowly into
the hot oil or fat. Frozen food in particular, will cause
frothing and spitting if added too quickly.
- keep outside of pans clean and free from streaks of oil or
fat.
- place pans centrally over the burner making sure handles
are kept away from the edge of the hob and cannot be
heated by other burners/pans.
- keep any ventilation slots clear of obstructions.
NEVER:
- attempt to install or repair the appliance without the
assistance of qualified personnel.
- store items above the appliance that children may attempt
to reach.
- heat up unopened food containers, as pressure can build
up causing the container to burst.
- use the appliance to heat up anything other than food.
- use the appliance as a room heater.
- dry any items on the hob.
- install the appliance next to curtains or other soft
furnishings.
- allow children to play with or tamper with the controls.
-leave children unsupervised where cooking appliances are
installed as all the cooking surfaces get hot during and
after use.
- store chemicals, foodstuffs or pressurised containers in
or on the appliance, or in cabinets immediately above or
next to the appliance.
- use flammable or plastic items on or near the hob.
- use adapters, multiple sockets and/or extension leads.
- fill a deep fat frying pan more than 1/3 full of oil, or use a
lid. DO NOT LEAVE UNATTENDED WHILE COOKING.
- fry too much food at a time, especially frozen food. This
only lowers the temperature or the oil or fat too much,
resulting in greasy food.
- pull on the appliance or the supply able to unplug it from
the electrical outlet.
- allow power cables of other appliances to come into
contact.
- with hot parts of this appliance.
- expose the appliance to atmospheric agents, such as
rain or sunlight.
- operate the appliance with wet hands.
- allow anyone to sit or stand on any part of the appliance.
- use misshapen pans which may be unstable.
- use round base woks directly on the pan supports.
- use fish kettles or large preserving pans across two
burners.
- operate the appliance with wet parts of the body.
- operate the appliance when barefoot.
When used properly your appliance is completely safe but as with any electrical product there are certain
precautions that must be observed.
PLEASE READ THE BELOW PRECAUTIONS BEFORE USING YOUR APPLIANCE.
To maintain the efficiency and safety of this appliance, we recommend you do the following:
- only call the Service Centres authorised by the manufacturer.
- always use genuine spare parts.
SAFETY ADVICE
IMPORTANT - As with any cooking appliance there could be some fire risk attached to the heating of oil, particularly
for deep fat frying. Cooking utensils containing oil must not be left unattended (eg. to answer the telephone) on or in
close proximity to the cooking areas.
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:
1. Turn off the burners.
2. Cover the pan with a fire blanket or damp cloth, this will smother the flames and extinguish the fire.
3. Leave the pan to cool for at least 60 minutes before moving it. Injuries are often caused by picking up a hot pan and
rushing outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the
pan over. Never use water to extinguish oil or fat fires.
5
How To Use Your Hob
Know your Hob
The position of the corresponding gas burner is indicated
on each control knob.
The burners differ in size and power. Choose the most
appropriate one for the diameter of the cookware being
used.
The burner can be regulated with the corresonding control
knob by using one of the following settings:
• Off
High
Low
To light a burner, simply press the corresponding knob all
the way in and then turn it in the counter-clockwise direction
to the "High" setting, keeping it pressed in until the burner
lights.
This model is fitted with a safety device (F), the knob
must be pressed in for about 6 seconds until the device
that keeps the flame lighted warms up.
Caution: If the burner accidently goes out, turn off the gas
with the control knob and try to light it again after waiting
at least 1 minute.
To turn off a burner, turn the knob in the clockwise
direction until it stops (it should be on the “•” setting).
A. Gas Burners
B. Support Grid for Cookware
C. Control Knobs for Gas Burners
D. Ignitor for Gas Burners (only on certain models)
E. Ignition Button for Gas Burners (only on certain
models)
F. Safety Device (only on certain models) - Activates if
the flame accidentally goes out (spills, drafts, etc.),
interrupting the delivery of gas to the burner.
B
A
C
D
F
6
Practical Advise on Using the Burners
For best performance, follow these general guidelines:
• Use the appropriate cookware for each burner (see
table) in order to prevent the flame from reaching the
sides of the pot or pan;
• Alwasy use cookware with a flat bottom and keep the
lid on;
• When the contents come to a boil, turn the knob to
"Low".
Practical Advice
Burner Cookware Diameter
(cm)
Reduced Rapid (R) 24 - 26
Semi-Fast (S) 16 - 20
Auxilliary (A) 10 - 14
Triple Crown (TC) 24 - 26
To identify the type of burner, refer to the 'Burner and Nozzle
Specifications' section.
7
Care and Cleaning
Before cleaning or performing maintenance on your hob,
disconnect it from the power supply.
To extend the life of the hob, it should be cleaned
carefully and thoroughly on a frequent basis, keeping
in mind the following:
• The enamelled parts must be washed with warm water
without using abrasive powders or corrosive substances
which could ruin them.
• The removable parts of the burners should be washed
frequently with warm water and soap, making sure to
remove caked-on substances.
• On hobs with automatic ignition, the end of the
electronic ignition device must be cleaned carefully and
frequently, making sure that the gas holes are not
clogged.
• Stainless steel can be stained if it remains in contact
with highly calcareous water or aggressive detergents
(containing phosphorous) for an extended period of time.
It is recommended that these parts be rinsed thoroughly
with water and then dried well. It is also a good idea to
clean up any spills.
Greasing the Gas Valves
Over time, the gas valves may stick or become difficult to
turn. If this is the case, the must be cleaned on the inside
and the regreased.
N.B.: This procedure must be performed by a technician
authorized by the manufacturer.
Troubleshooting
If the burner does not remain on when set to "Low".
Check to make sure that:
• The gas holes are not clogged.
• There are no draughts near the cooking surface.
• The minimum has been adjusted correctly (see
Installation section, "Minimum Regulation").
If the cookware is not stable.
Check to make sure that:
• The bottom of the cookware is perfectly flat.
• The cookware is centered correctly on the burner .
• The support grids have not been inverted.
If, despite all of these checks, the hob does not function
properly and problem persists, call Hotpoint Service (see
KEY CONTACTS, back page), informing them of:
- The type of problem.
- The abbreviation used to identify the model (Mod. ...) as
indicated on the warranty.
IMPORTANT:
Never call upon technicians not authorized by the
manufacturer, and refuse to accept spare parts that are
not original.
Before calling service for assistance, check through the
following list, there may be nothing wrong.
First of all, check to see that there are no interruptions in
the gas and electrical supplies, and, in particular, that the
gas valves for the mains are open.
If the burner does not light or the flame is not
uniform around the burner.
Check to make sure that:
• The gas holes on the burner are not clogged.
• All of the movable parts that make up the burner are
mounted correctly.
• There are no draughts around the cooking surface.
If the flame does not stay lit on a model with the
Flame Failure device.
Check to make sure that:
• You press the knob all the way in.
• You keep the knob pressed in long enough to activate
the flame failure device.
• The gas holes are not clogged in the area corresponding
to the flame failure device.
8
Installation
The following instructions are intended for the installer so that
the installation and maintenance procedures may be followed in
the most professional and expert manner possible. Important:
Disconnect the appliance from the electrical supply before
performing any maintenance or repair.
Positioning the Hob
Important: this unit may be installed and used only in permanently
ventilated rooms in accordance with British Standard Codes Of
Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891 Current
Editions. The following requirements must be observed:
a) The room must be fitted with a ventilation system which
vents smoke and gases from combustion to the outside.
This must be done by means of a hood or electric ventilator
that turns on automatically each time the hob is operated.
In a chimney stack or branched flue. Directly to the Outside
(exclusively for cooking appliances)
b) The room must have an air flow to allow for proper combustion.
This must be 2 m
3
³/h per kW of installed power. The airflow
can be created using an enclosed vent with an inner cross
section of at least 100 cm² which must not be able to be
blocked. I the appliance does not have a flame failure device,
the vent must have an internal cross section of 200 cm
3
³
(Fig. A). Alternatively the room in which the hob is situated
can be vented indirectly through ventilation ducts as specified
above, as long as the adjacent room is not a shared area, a
bedroom or present any risk of fire (Fig. B).
Detail A Adjacent Room to be
Room Vented
A
Examples of ventilation holes Enlarging the ventilation slot
for comburant air. between window and floor.
Fig. A Fig. B
c) Intensive and prolonged use of the appliance may necessi-
tate supplemental ventilation, e.g. opening a window or
increasing the power of the air intake system (if present).
d) Liquidified petroleum gases are heavier than air and, as a
result, settle downwards. Rooms in which LPG tanks are
installed must be fitted with ventilation openings to the outside
in order to allow the gas to escape in the event of a leak.
Therefore, LPG tanks, whether empty or partially full, must
not be installed or stored in rooms or spaces below ground
level (cellars, ect.). It is also a good idea to keep only the
tank currently being used in the room, making sure that it is
not near sources of heat (ovens, fireplaces, stoves, etc.)
that could raise the internal temperature of the tank above
50°C.
Installation of Built-in Hobs
The gas hob is equipped with type X degree protection against
overheating. Therefore, the appliance can be installed next to
cabinets, provided the height of the cabinet does not exceed
that of the hob. For proper installation of the hob, the following
guidlines must be followed:
a) If the cabinet(s) located next to the hob are higher than the
hob itself, the cabinet(s) must be installed at least 110 mm
from the hob edge.
b) Hoods must be installed in accordance with the instructions
contained in the installation manual for the hoods themselves,
and no less than 650 mm from the hob.
c) In the case of the 600 mm cooker hoods, besides following
the recommendations in point b), the cabinets should be
positioned next to the hood at a height of at least 540 mm
from the top since this will make it possible to install the lid
and move it correctly. The cabinet should always be installed
at a height from the top which allows easy use of pots and
pans on the cooker.
d) Should the hob be installed directly under a cupboard, the
latter should be at least 700 mm (millimetres) from the top,
as shown in Figure C.
Fig. C
e) The dimensions of the cutout for the appliance must be those
indicated in the figure D. Clamps are provided to fasten the
hob to counters measuring from 20 to 40 mm in thickness.
To fasten the hob securely, it is recommended that all the
clamps be used.
Fig. D
555 mm
475
mm
55 mm
600mm min.
540mm min.
700mm min.
9
Gas Connection for the Hob
The hob should be connected to the gas supply by an authorized
installer. During installation of this product it is essential to fit an
approved gas tap to isolate the supply from the appliance for the
convenience of any subsequent removal or servicing. Connection
of the appliance to the gas mains or liquid gas tanks must be
carried out according to the safety standards currently in force,
and only after it is ascertained that it is suitable for the type of
gas to be used. If not, follow the instructions indicated in the
section entitled, “Adapting the Hob for Different Types of Gas”. If
the hob is to be connected to tanks containing liquid gas, use
pressure regulators that comply with current safety standards.
Important: To insure that the appliance operates safety, the gas
is regulated correctly and your appliance lasts over time, make
sure that gas pressure levels comply with the indications given
in Table 1, “Nozzle and Burner Specifications”.
Gas Connection to Non-flexible Pipe
(copper or steel)
Connection to the gas source must be done in such a way as to
not create any stress points at any part of the appliance.
The appliance is fitted with an adjustable, "L" shaped connector
and a gasket for the attachment to the gas supply. Should this
connector have to be turned, the gasket must be replaced
(supplied with the appliance).
The gas feed connector to the appliance is a threaded, male 1/
2" connector for round gas pipe.
Gas Connection to Flexible Steel Pipe
The gas feed connector to the appliance is a threaded, male 1/2"
connector for round gas pipe. Only use pipes, tubes and gaskets
that comply with current safety codes. The maximum length of
the flexible pipes must not exceed 2000 mm. Once the connection
has been made, ensure that the flexible metal tube does not
touch any moving parts and is not crushed.
Check the Seal
Once the hob has been installed, make sure all the connections
are properly sealed, using a soapy water solution. Never use a
flame.
Fastening Clamps - Assembly Diagram
Clamp Position for Clamp Position for
H=20mm top H=30mm top
Front
Clamp Position for
H=40mm top Back
N.B: Use the clamps contained in the "accessory kit."
f) In the event the hob is not installed above a built-in oven, a
wood panel must be inserted as insulation. This panel must
be placed at least 20 mm from the bottom of the hob itself.
Important: When installing the hob above a built-in oven, the
oven should be placed on two wooden strips; in the case of a
joining cabinet surface, remember to leave a space of at least 45
x 560 mm at the back.
560 mm.
45 mm.
When installing the hob above a built-in oven without forced
ventilation, ensure that there are air inlets and outlets for ventilating
the interior of the cabinet adequately.
Installation
10
Adapting the Hob for Different Types of Gas
To adapt the hob to a different type of gas than that for which it
was designed, (see the sticker under the hob or on the packaging),
the burner nozzles must be changed, as follows:
• Remove the pan supports and slide the burners out of the
cooktop.
• Unscrew the nozzles using a 7mm socket wrench and replace
them with those for the new type of gas. (See table 1, “Burner
and Nozzle Specifications”).
• Reassemble the parts following the instructions in reverse
order.
• On completing the operation, replace the old rating label with
the one showing the new type of gas; the sticker is available
from Hotpoint Service (see KEY CONTACTS, back page).
If the gas pressure is different than that prescribed, a pressure
regulator must be installed at the source, in compliance with
national standards governing the use of piped gas regulators.
Regulation of Air Supply to the Burner
The burners do not need a primary air regulator.
Minimum Regulation
• Turn the gas valve to minimum.
• Remove the knob and turn the regulator screw (positioned
either on the side of the top or inside the shaft) clockwise
until the flame becomes small but regular.
N.B.: In the case of liquid gas, the regulation screw must be fully
screwed in (clockwise).
• Make sure that, when the knob is turned rapidly high to low,
the flame does not go out.
• In the event of a malfunction on appliances with the security
device (thermocouple) when the gas supply is set at minimum,
increase the minimum supply levels using the regulator screw.
Once the adjustment has been made, apply sealing wax, or a
suitable substitute, to the old seals on the by-pass.
Installation
11
Electrical Connection
GREEN &
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
Electrical connection
Ovens with a three-pole power supply cable are designed
to operate with alternated current at the supply frequency
and voltage indicated on the data plate (at the bottom of
the oven dashboard). The earthing conductor of the cable
is the yellow-green conductor.
Two types of connection are provided:
Connection n° 1
Connecting the power supply cable to the mains.
Fit a normalized plug to the cable, which corresponds to
the load indicated on the data plate; if the appliance is
connected directly to the mains, an omnipolar circuit-
breaker with a minimum opening of 3 mm between the
contacts, suitable for the load indicated and complying
with current directives, must be installed between the
appliance and the mains (the earthing wire must not be
interrupted by the circuit-breaker). The power supply cable
must be positioned so that it does not exceed room tem-
perature by 50°C at any point of its length. Before making
the connection check that:
• the circuit breakers or fuses of the home system can
support appliance load (see data plate);
• the power supply system has an efficient earthing
connection which complies with the provisions of current
regulations and the law;
• there is easy access to the socket or the omnipolar
circuit-breaker once the cooker has been installed.
N.B.: do not use reducers, adapters or shunts as these
could cause heating or burning.
Connection n° 2
Disposing of the plug.
WARNING: THIS APPLIANCE MUST BE EARTHED.
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket. Instructions for connecting cable to an alter-
native plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow -Earth
Blue -Neutral
Brown -Live
If the colours of the wires in the mains lead do not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows.
Connect Green & Yellow wire to terminal marked “E” or $
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse.
A 15 amp plug must be protected by a 15 amp fuse, either
in the plug or adaptor or at the distribution board.If you are
in any doubt about the electrical supply to your machine,
consult a qualified electrician before use.
How to connect an alternative plug
The wires in this mains lead are coloured in accordance
with the following code:
BLUE “NEUTRAL” (N)
BROWN “LIVE” (L)
GREEN AND YELLOW “EARTH” (E)
Disposing of the appliance
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the
plug body and dispose of it as described above.
The plug and socket must be easily accessible.
12
Characteristic of the burners and nozzles
*At 15°C and 1013 mbar-dry gas
** Propane P.C.S. = 50.37 MJ/kg.
*** Butane P.C.S. = 49.47 MJ/kg.
Natural P.C.S. = 37.78 MJ/m
3
(1) re. Models with the security device (Ref. F).
S
A
TC
RR
S
GC750TX
Table 1
Liquid Gas Natural Gas
Burner Diameter
(mm)
Thermal power
kW (p.c.s.*)
By-Pass
1/100
Nozzle
1/100
Flow*
g/h
Nozzle
1/100
Flow*
l/h
Nomin. Ridot. (mm) (mm) *** ** (mm)
Reduced Fast
(RR)
100 2,60 0,70 41 80 189 186 110 248
Semi Fast (S) 75 1,90 0,40 30 70 138 136 106 181
Auxiliary (A) 55 1,00 0,40 30 50 73 71 79 95
Triple Crown
(TC)
130 3,60 1,30 57 94 262 257 137 343
Supply
Pressures
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
GB
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts
and labour guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales
service options:
Repair Service and Information Help Desk
UK: 08709 066066
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance
Available 364 days a year with a fast, effective and value for money service. We have the largest white
goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a
parts and labour guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with
help and advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover
plans to give you total peace of mind.
●
Repair Protection Plan - FREE service repairs for a single Hotpoint appliance during the period
of cover.
●
Kitchen Cover - FREE service repairs for all your Hotpoint appliances less than 8
years old.
Genuine Parts and AccessoriesUK: 08709 077 077
www.theservicecentre.co.uk
Republic of Ireland: (01) 842 6836
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
www.theservicecentre.co.uk
After Sales Service
13
GB
Guarantee
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service
or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for an
engineer to call. If the technical problem is not resolved under this guarantee, we will replace your
machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker
hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
●
Has been installed and used correctly in accordance with this instruction booklet.
●
Has been used solely for domestic purposes and is located on domestic premises (ie. not for
commercial or trade use).
●
Has been properly connected to a suitable electrical supply voltage as stated on the appliance
rating plate.
●
Has not been subject to misuse, accident, modified or repaired by anyone other than one of our
own service engineers.
For pre purchase information on any other Hotpoint product call: 08701 50 60 70
or visit: www.hotpoint.co.uk
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the
appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged
into a mains socket, and the door cannot be locked shut.
14
11-2005 Part no. FP157 - 01
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in
both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number:
Serial number:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
www.theservicecentre.co.uk
Republic of Ireland: (01) 842 6836
Indesit Company UK Ltd, Morley Way, Peterborough, PE2 9JB.
Key Contacts
After Sales Service
195.046.613.01
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
