Panasonic MCUL672 Operating instructions

Brand: Panasonic

Model: MCUL672

Category: Vacuum cleaners

Type: Operating instructions

Panasonic MCUL672 is a vacuum cleaner designed for general household use. It features a telescopic handle for easy reach and storage, a mains lead reel for convenient cord management, and an ON/OFF switch for simple operation. The vacuum cleaner also comes with a variety of accessories, including a crevice tool, dusting brush, and upholstery nozzle, making it suitable for cleaning a wide range of surfaces. Additionally, the vacuum cleaner is equipped with a motor protector and thermal cut-out for safety and peace of mind.

Operating Instructions

Vacuum Cleaner

Model No. MC-UL672

We would advise that you carefully study these Operating Instructions before attempting

to operate the vacuum cleaner and that you note the Important Safety Instructions.

Please keep in a safe place with your Authorised Dealer Service booklet.

This product complies with the European directive 73/23/EEC and 89/336/EEC and with the Australian

Standards AS 3350.2.2 (1995) and Australian EMC requirements for the C-Tick Mark.

Matsushita Electric Industrial Co., Ltd

http://www.panasonic.co.jp/global/

CØ1ZDBVØØEØØ

ACØ1ZDBVZØEØ

Printed in P.R.C.

REMINDER FOR CUSTOMER

The model and serial number of the product

may be found on the nameplate located at the

back of your vacuum cleaner. You should note

the model and serial number in the spaces

provided and retain this book for future

reference.

Model Number: ....................................

Serial Number:......................................

Date Purchased: ..................................

Where Purchased:................................

- 2 -

Page

• Caution for AC Mains Lead (UK and Republic of Ireland only) ..........2

• Important Safety Instructions for the user ..........................................3

• Cautions ............................................................................................3

• Identification of main parts ................................................................4

HOW TO OPERATE YOUR VACUUM CLEANER

A) How to attach the telescopic handle ..............................................4

B) How to attach the hose....................................................................5

C) How to use the telescopic handle....................................................5

D) Mains lead reel................................................................................6

E) ON/OFF Switch ..............................................................................6

F) Handle lock / release by foot pedal ................................................6

G) How to use the accessories ............................................................7

H) Motor protector ................................................................................7

I ) Thermal cut-out ................................................................................7

TABLE OF CONTENTS

Page

MAINTENANCE AND SERVICING

A) Vacuum cleaner storage ......................................8

B) Cleaning exterior and

accessories

........................8

C) Dust bin cleaning and removal..............................9

D) Dust bin filter changing and cleaning ......................10

E) Cleaning secondary filter screen ........................11

F) Exhaust filter maintenance..................................11

G) Belt changing and cleaning............................12,13

H) Blockages............................................................14

I ) How to remove the telescopic handle..................14

J) Trouble-shooting guide ........................................15

• Specifications ........................................................16

• Consumables / Accessories ..................................17

• Disposal information ..............................................18

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has rating of 13 amps and that it is approved

by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.

If in any doubt please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or

coloured RED.

Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with

the letter E or the Earth Symbol

How to replace the Fuse:

• There are two types of the supplied AC Mains Lead : A and B as shown below.

1 Open the fuse compartment with a screwdriver.

2 Replace the fuse and fuse cover if detachable.

ASA

CAUTION FOR AC MAINS LEAD (UK and Republic of Ireland only)

TYPE A TYPE B

- 19 -

CAUTIONS

• Do not leave the vacuum cleaner plugged into mains socket. Unplug from the socket when not in use and before cleaning

the appliance or undertaking maintenance operations.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Do not use if the mains lead or mains plug is damaged. If the vacuum cleaner is not working as it should be, or has been

dropped, damaged, left outdoors, or come into contact with water, consult an authorised Panasonic Service Centre.

• Do not pull or carry by the mains lead, use the mains lead as a handle, close a door on the mains lead, pull the mains lead

around sharp edges or corners. Do not run over the mains lead with the vacuum cleaner. Keep the mains lead away from

heated surfaces.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that

may block or reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Do not use the vacuum cleaner without filters and /or dust bin in place.

• Do not use wet filters after wash, see D) Dust Bin filter Changing and Cleaning.

• Turn off all controls before unplugging.

• Do not use to pick up flammable or combustible materials, or others that may become so or use in areas where they may

be present.

• This appliance should be serviced by an authorised Panasonic Service Centre, and only genuine Panasonic spare parts

should be used.

• Use extra care when cleaning on stairs. Keep hold of the handle to prevent the vacuum cleaner from falling.

• To prevent damaging carpeted floors, tiled floors, Linoleum, etc. Do not leave the agitator rotating in the same place for

too long.

• Keep bare feet and hands away from the agitator. (It may cause injury)

NOTE: This vacuum cleaner is designed for general household use only and is not suitable for use in a garage,

garden or to suck up liquids.

Information on Disposal for Users of Waste Electrical & Electronic Equipment

(private households)

This symbol on the products and/or accompanying documents means that used electrical and

electronic products should not be mixed with general household waste. For proper treatment,

recovery and recycling, please take these products to designated collection points, where they will be

accepted on a free of charge basis. Alternatively, in some countries you may be able to return your

products to your local retailer upon the purchase of an equivalent new product. Disposing of this

product correctly will help to save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate waste handling.

Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of

disposal.

IMPORTANT SAFETY INSTRUCTIONS FOR THE USER

Before using the vacuum cleaner, please read these basic precautions.

WARNING: To reduce the risk of fire, electric shock, or injury.

1. To avoid any possible damage to

the mains lead, never run over the

mains lead or allow it to become

caught in the agitator when using

the vacuum cleaner.

2. Do not run the vacuum cleaner over

tassels or fringes of rugs or mats as

they could get caught up in the agitator

and may cause damage to belt.

3. Keep the vacuum cleaner away

from heat sources such as radiators,

fires, direct sunlight, etc.

4. To avoid damaging the vacuum

cleaner, never let the vacuum cleaner

pick up wet matter, mud, burning

ashes or large and sharp objects.

5. Do not pull on the mains lead when

disconnecting the appliance from the

mains, always pull on the plug body

itself.

6. To avoid injury, keep your fingers

and hands away from the agitator,

and never put them between the body

parts.

- 3 -- 18 -

DESCRIPTION MC-UL672

Primary filter Part number

AC95KDBVZØØØ

Exhaust filter Part number

HEPA Filter AC38KDBVZØØØ

Filter case Part number

AC42KDBVZVUT

Dust bin cover Part number

AC92LDDEZUØ3

Pre-filter Part number

AC43KDDEZVØ2

Filter supporter unit Part number

AC36KDBVZUØ3

Extension wand (with tabs) Part numbers

AC4ØPCHNZVØ6

Crevice nozzle Part number

AC6ØRCHPZVØ6

Dusting brush Part number

AC88RCHPZVØ6

Belt Part number

AC28SDDEZØØØ

Belt Part number

AC28SDBVZØØØ

Agitator assembly Part number

AC92SDBVZUØØ

Hose Part number

AC84PDBVZØØØ

Nozzle cover latch Part number

ACØ8DDBVZUØ3

IDENTIFICATION OF MAIN PARTS

Handle

On/Off switch

Hose

Crevice nozzle

Dust bin

Release handle

Upper dust bin

Primary filter

Pre-Filter

Lower dust bin

Exhaust filter

(inside)

Furniture guard

Cleaning head

Cord clip

Handle height

adjust button

Carrying handle

Suction inlet

Wands

Motor protector

Foot pedal

Nozzle hose

Mains lead

Cord retract pedal

Dust bin

release button

Vacuum Cleaner Consumables / Accessories

For customers within the UK:

For customers within the Republic of Ireland:

Note: Specifications are subject to change without notice.

Sales and Support Information

Customer Care Centre

• For customers within the UK: 0844 844 3868

• For customers within the Republic of Ireland:

01 289 8333

• Visit our website for product information

• E-mail: [email protected]

Direct sales at Panasonic UK

• Order accessory and consumable items for your product with

ease and confidence by phoning our Customer Care Centre

Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm

(excluding public holidays).

• Or go on line through our Internet Accessory ordering

application at www.panasonic.co.uk

• Most major credit and debit cards accepted.

• All enquiries transactions and distribution facilities are

provided directly by Panasonic UK Ltd.

• It couldn’t be simpler!

• Also available through our Internet is direct shopping for a

wide range of finished products, take a browse on our website

for further details.

HOW TO OPERATE YOUR VACUUM CLEANER

A) HOW TO ATTACH THE TELESCOPIC HANDLE

- 4 -

Alignment button

Handle opening

Line up telescopic handle with handle opening on top of

vacuum cleaner, and insert handle.

Ensure handle alignment button is in alignment slot in front of

handle opening and depress until handle slides down and is

engaged.

Depress handle height adjust button to allow handle to be

lowered into vacuum cleaner.

Push down on handle until it locks into place at desired height.

NOTE: You should hear a noticeable “click” sound when handle

reaches the operating position.

Handle height

adjust button

-17 -

- 5 -

Telescopic handle may be raised or lowered as desired for

vacuuming or storage.

To raise or lower the telescopic handle to one of four (4)

positions, depress handle height adjust button and position

the handle to the desired setting.

NOTE: You should hear a noticeable “click” sound when

handle reaches the operating position.

Make sure the handle is locked in the operating position

before using the vacuum cleaner. DO NOT operate the

vacuum cleaner unless handle is locked.

NOTE: Always lift the vacuum cleaner by the carrying handle

when transporting to storage.

Cord clip

Carrying handle

Handle height

adjust button

- 16 -

MODEL NO. MC-UL672

POWER SOURCE 230-240V / 50Hz

MAX. INPUT POWER 2000w

MOTOR PROTECTION YES

DUST BIN CAPACITY 1.8 litres

EXHAUST FILTER HEPA

DIMENSIONS (W x L x H) 362x397x1000 mm

NET WEIGHT 11.0kg

DUSTING BRUSH

YES

PIPE YES

CREVICE NOZZLE YES

SPECIFICATIONS

C) HOW TO USE YOUR TELESCOPIC HANDLE

B) HOW TO ATTACH THE HOSE

Hose Coupling

Hose Inlet

Aligned hose connector and the connector pipe.

Push down to a press fitting.

Connector Pipe

Hose connector

To assemble hose coupling:

Depress tab A and tab B as shown.

Install hose coupling into hose inlet.

Stretch hose and wrap around vacuum cleaner.

E) ON/OFF SWITCH

F) HANDLE LOCK / RELEASE BY FOOT PEDAL

Release the handle by pressing down on

the foot pedal with your foot and pulling

back and down on the handle with your

hand.

CAUTION: To prevent

damaging carpeted floors,

tiled floors, linoleum, etc.

Do not leave the agitator

rotating in the same place

for too long.

Step a second time

To start or stop the vacuum cleaner, push the switch button

to ‘I’ to turn ON and to ‘O’ to turn OFF.

NOTE: After use, unplug from the

mains and store the vacuum cleaner in

the upright position.

- 6- - 15 -

TROUBLE-SHOOTING GUIDE

Before contacting your Panasonic service centre, check the following points:

NOTE: Failure to correctly maintain your product, for example regular cleaning and unblocking, may result in a charge if referred

to a service agent for attention.

CAUTION:DISCONNECT from the mains socket before carrying out any kind of maintenance

operation.

TROUBLE CHECK POINT CAUSE / REMEDY

Motor fails to rotate • Mains plug connection • Check that the mains plug is connected firmly and

(no noise is heard at all) mains socket is ON.

• Mains plug fuse. (UK, IRL only) • Check fuse and replace if blown.

• Thermal cut-out device may have • (See Thermal cut-out protection feature below

operated. described).

Motor runs but there • Hose inlet is blocked. • If there is a blockage, remove it.

is no suction. see (BLOCKAGES)

• Check dust mark. • If it shows full, empty the dust bin.

• Primary filter • If the primary filter is full of dust, clean it or

replace. (see DUST BIN FILTER CHANGING AND

CLEANING)

• Check hose is properly inserted • Re-insert the hose to suction pipe inlet correctly.

to the suction pipe inlet.

• Check dust accumulated on primary • Remove dust accumulated or replace the filters.

filter. (see DUST BIN FILTER CHANGING AND

CLEANING)

• Exhaust filter. • If exhaust filter is full of dust replace it.

(see EXHAUST FILTER MAINTENANCE)

• Dust bin inlet is blocked. • If there is a blockage, remove it.

(see BLOCKAGES)

Agitator does not • Clogged by a large object in • If there is any obstruction, remove it.

rotate. the agitator housing.

• Belts broken or loose. • If the belt is broken, replace it.

If loose re-install it.

THERMAL CUT-OUT

This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the vacuum cleaner to prevent

overheating of the motor. When this happens, disconnect the vacuum cleaner from the mains socket and check the dust bin and

filters as it may be full or clogged with fine dust. Check for any other obstructions.

After emptying the dust bin or removing the obstruction, leave the vacuum cleaner to cool down until the thermal cut-out resets

after approximately 40 minutes.

IMPORTANT: The thermal cut-out will not reset if the vacuum cleaner is not disconnected from the mains socket.

MAINS LEAD

IMPORTANT: If the mains lead becomes damaged, it must be repaired by Panasonic, authorised service centre or a

qualified person in order to avoid any hazard.

On-Off

Switch

D) MAINS LEAD REEL

To prevent injury or damage, hold plug head while rewinding

mains lead

Push

mains lead

retract pedal down to rewind.

Pull

mains lead

out of

mains

reel until the end is reached.

Do not use vacuum cleaner without

mains lead

pulled out all

the way.

Push

mains lead

into

mains lead

clip in back of vacuum

cleaner.

Plug the polarized

mains lead

into a 240V mains located near

floor.

Use low position for cleaning under

furniture. To move the vacuum cleaner to

the low position press the foot pedal

again.

- 7 -

This vacuum cleaner has a thermal cut-out which

automatically trips to protect the vacuum cleaner from

overheating. If a clog prevents the normal flow of air to the

motor, the thermal cut-out turns the motor off automatically to

allow the motor to cool in order to prevent possible damage to

the vacuum cleaner.

To correct problem: If this occurs, turn the vacuum cleaner

off and unplug the vacuum cleaner from the mains outlet to

allow the vacuum cleaner to cool and the thermal cut-out to

reset. Check for and remove clogs, if necessary. Also

check and clean/replace any clogged filters. Wait

approximately forty (40) minutes before switching on the

vacuum cleaner. The motor protector will not reset if the

vacuum cleaner is not disconnected from the mains

socket even if the vacuum cleaner has cooled down.

H) MOTOR PROTECTOR

Motor Protector

This vacuum cleaner has a motor protector by-pass valve

which automatically opens to provide cooling air to the

motor when a clog prevents the normal flow of air to the

motor. If the by-pass valve opens to prevent motor

overheating and possible damage to the vacuum cleaner,

you will notice a change of sound as air rushes through the

valve opening.

To correct problem: See the TROUBLE-SHOOTING

guide.

NOTE: The motor protector may open when using

attachments or when cleaning new carpet, due to reduced

airflow by the attachments themselves or by new carpet

fluff filling the dust bin quickly. See the TROUBLE-

SHOOTING guide.

I) THERMAL CUT-OUT

CAUTION:

Do not block motor protector.

- 14 -

BLOCKAGES

Hose Coupling

Suction Inlet

Hose Inlet

Secondary

Filter Screen

The hose located on the vacuum cleaner carries the dirt

from the nozzle up to the dust bin. If the hose should

become clogged:

Unplug the vacuum cleaner from mains outlet.

Remove hose coupling and check hose coupling and hose

inlet for clogs according to the following procedure.

To remove hose coupling:

1.Depress and tilt tab A as shown.

2.Once tab A is clear of the vacuum cleaner inlet, depress

and tilt tab B as shown.

To re-install hose coupling: Reverse steps above.

Check suction inlet and secondary filter screen for clogs.

Disconnect nozzle hose from connector pipe, check the

hose. Plug in vacuum cleaner and turn on.

Stretch hose in and out to remove clog. If clogs still exist,

turn the vacuum cleaner over and inspect agitator area for

clogs, see BELT CHANGING AND CLEANING for details.

Connector Pipe

Nozzle

Hose

I ) HOW TO REMOVE THE TELESCOPIC HANDLE

With the handle on its lowest position, depress the handle

height adjustment button and raise handle about 6 cm

while turning it counterclockwise.

You should be able to turn the handle 90° to a transversal

position.

Pull handle straight out until free from vacuum cleaner. Do

not use excessive force.

Handle height

adjust button

G) HOW TO USE THE ACCESSORIES

CAUTION:While using

the accessories, hold

the handle with one

hand to avoid pulling the

vacuum cleaner over.

Lift out accessories needed.

To prevent damage to carpeted

floors when using tools, the vacuum

cleaner should not remain in one

place for a period of time.

NOTE: After using the accessories, re-insert the hose to the connector pipe.

To avoid accidental injury,

keep children away from the

agitator while in operation.

Connect any of the accessories, as indicated.

CAUTION:

Do not use attachments if they are wet.

Attachments used in dirty areas, such as under a refrigerator,

should not be used on other surfaces until they are washed. They could leave marks.

To return the handle to the storage position when the vacuum cleaner is not

in use, press handle release button and push the handle down for easy

storage.

NOTE: You should hear a noticeable “click” sound when handle reaches the

storage position.

MAINTENANCE AND SERVICING

A) VACUUM CLEANER STORAGE

Handle

Release

Button

Operating

Position

Storage

Position

Always follow all safety precautions when cleaning and servicing the vacuum cleaner.

WARNING:

Electrical Shock And Personal Injury Hazard

Disconnect from electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in

electrical shock or personal injury from vacuum cleaner suddenly starting.

CLEANING EXTERIOR AND ACCESSORIES

- 8 -

- 13 -

Motor

Shaft

Belt

Pulley

Belt

Pulley

Nozzle

Base

Slot

End

Cap

Agitator

TO REPLACE BELT

Seat left end of agitator into nozzle base. To seat agitator

end, place rounded portion of agitator end cap down into slot

in nozzle base.

Loop the new belt on the belt pulley.

Loop the other end of belt onto the belt pulley on the right

end of agitator.

Pull right end of agitator forward and seat it into nozzle base.

Belt

Agitator

Press firmly, checking to see that each end is completely

inserted.

Check to see that the belt is centered on the belt pulley and

that the agitator turns freely.

Nozzle

Cover

Nozzle Cover

Retainer

Tab

Make sure the nozzle cover retainers are in the UNLOCK

position. Hook the front of the nozzle cover on to the nozzle

base and rotate downward. Make sure tabs snap in. Once in

place, rotate the nozzle cover retainers to the LOCK

position.

Disconnect mains plug from wall outlet.

Clean exterior using a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry. Wipe

dry after cleaning. DO NOT drip water on vacuum cleaner.

Wash attachments in warm soapy water, rinse and air dry. Do not clean in dishwasher.

DO NOT use accessories if they are wet.

- 9 -

Lid Release Lever

Dust Bin Lid

DUST BIN CLEANING AND REMOVAL

TO REMOVE DUST BIN

Remove dust bin assembly from vacuum cleaner by pressing

the release button as shown.

Remove dust bin from vacuum cleaner tilting it out as shown.

CAUTION:

Electrical Shock And Personal Injury Hazard

Always disconnect the vacuum cleaner from mains outlet before carrying out any service or maintenance on the

vacuum cleaner.

Always empty the dust bin when dirt level reaches the “MAX FILL” line.

Press the dust bin lid release lever.

Empty wastes into the trash container.

- 12 -

BELT CHANGING AND CLEANING

WARNING:

Electrical Shock And Personal Injury Hazard

Disconnect from electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in

electrical shock or personal injury from vacuum cleaner suddenly starting.

Frequently check and remove hair, string and lint build-up in the brush area. If build-up becomes excessive, follow the steps below.

Should the belt become loose or should it break, follow the Belt Removal Instructions.

TO REMOVE NOZZLE COVER

Disconnect from electrical supply.

Press foot pedal and tilt the

handle down so the vacuum cleaner is laying flat on the floor.

To protect the floor surface, always place paper under the

nozzle any time the nozzle cover is removed.

Release the nozzle cover by rotating the nozzle cover retainers

to the UNLOCK position and depress tabs to remove. Grasp

back of nozzle cover on each side and lift up to remove it from

nozzle.

Nozzle

Cover

LOCK

UNLO

LOCK

UNLOCK

Nozzle Cover

Retainer

Tab

Agitator

Belt

WARNING:

Personal Injury Hazard

Always unplug the vacuum cleaner before cleaning the brush area as agitator may suddenly restart. Failure to

do so can result in personal injury.

Carefully remove any residue that may exist in the belt area.

TO REMOVE BELT/CLEAN AGITATOR

Position hands on the agitator. If the belt is still attached to the

agitator, there will be tension on it.

Carefully lift the right end (belt side) of the agitator and then lift

the left end.

Remove the worn or broken belt from the pulley or motor drive

shaft.

WARNING:

Personal Injury Hazard

Be careful when removing the agitator as the belt

tension is high. Failure to do so could result in

personal injury from the agitator releasing quickly

and snapping away.

Usage

Clean Agitator

HEAVY - every week

(used daily)

MODERATE - every month

(used 2-3 times/week)

LIGHT - every 2 months

(used 1 time/week)

End

Cap

Cut off any carpet pile, hair or lint

entangled around the agitator and

remove any string or debris located

near the end caps.

NOTE: In order to keep cleaning efficiency high and to prevent

damage to your vacuum cleaner, the agitator must be cleaned

every time the belt is changed.

TO EMPTY DUST BIN

Hold dust bin over a trash container.

TO REPLACE DUST BIN

First align base of dust bin with the vacuum cleaner.

Then

push dust bin back in place making sure dust bin is securely

latched.

Push the dust bin lid to close the dust bin.

NOTE: You should hear a noticeable “click” sound when lid

locks in place.

- 11 -

CLEANING SECONDARY FILTER SCREEN

The secondary filter screen protects the motor.

Always check filter screen when cleaning dust bin.

If dirty or clogged, remove debris from filter screen.

Secondary

Filter Screen

EXHAUST FILTER MAINTENANCE

The exhaust filter removes dirt from recirculated air.

Check filter after emptying dust bin.

To remove, press on the filter cover latch, pull both sides of

the exhaust filter cover with a counter-clockwise movement.

Grasp the HEPA exhaust filter and pull out to remove.

Replace the exhaust filter making sure that the foam seal on

the exhaust filter is down and the arrows indicating the air

flow direction point up.

Reinstall exhaust filter cover by snapping into place.

IMPORTANT - Exhaust Filter cannot be cleaned and should

be replaced at least once each year.

Exhaust

Filter Cover

Tab

Latch

HEPA

Exhaust Filter

- 10 -

DUST BIN FILTER CHANGING AND CLEANING

Check primary filter frequently and clean when dirty. Remove the dust bin assembly as outlined in the DUST BIN CLEANING

section and empty contents of dust bin.

Grasp primary filter and push it against the inner wall of the

upper dust bin to release it. Then pull primary filter straight

out from upper dust bin as shown.

Clean primary filter by gently tapping over a trash container.

CAUTION: Make sure upper dust bin is empty

before filter is removed.

CAUTION: Rinse with water only, do not use detergent or soap.

Allow filter to dry 24 hours before putting it

back into the dust bin.

When the cleaning of the filter no longer restores vacuum cleaner suction to full

power you need to replace the filter.

CAUTION:

When cleaning filter, do not use

brush or other similar tools that would damage

the filter itself.

Simply tap the filter on the edge of cap for normal dry cleaning.

For more thorough cleaning, rinse outside of filter with water and allow to dry thoroughly before reuse in vacuum cleaner.

Rotate upper dust bin clockwise from the locked position to

the unlocked position as shown.

Separate the upper dust bin from the lower dust bin by lifting

it straight off.

Locking Tabs

TO ASSEMBLE THE DUST BIN

Align the filter with the locking tabs in the dust bin and push

down until you hear a click.

TO CLEAN PRE-FILTER

Turn clockwise and pull the pre-filter. Clean by gently tapping

over a trash container.

Assemble and align the top and bottom of dust bin. Turn

counter-clockwise to the lock position.

Return the pre-filter to the dust bin, aligning the filter screen

tabs to the lower dust bin slots, then turn counter-clockwise

to the lock position.

A retention clip is located on the hinge area of the dust

bin.

This clip may release when the dust bin door is opened

to prevent damage to the door or the dust bin.

To reassemble, slide the tabs on the dust bin door into

the slots on the dust bin.

Secure in place using the retention clip.

Panasonic MCUL672 Operating instructions

Brand: Panasonic

Model: MCUL672

Category: Vacuum cleaners

Type: Operating instructions

Download PDF

report

Panasonic MCUL672 Operating instructions

Panasonic MCUL672 Operating instructions

Related papers

Other documents