AEG 75301K-MN User manual

Category
Hobs
Type
User manual

This manual is also suitable for

75301K
Glaskeramik-Kochfeld
Ceramic glass hob
Encimera de vitrocerámica
Montage- und Gebrauchsanweisung
Installation and Operating Instructions
Instrucciones para el montaje y para el uso
36
Dear customer,
Please read these operating instructions carefully.
Pay particular attention to the section “Safety information” on the first
few pages. Please retain these operating instructions for later refer-
ence. Pass them on to possible new owners of the appliance.
The following symbols are used in the text:
1 Safety instructions
Warning: Information concerning your personal safety.
Important: Information on how to avoid damaging the appliance.
3 Information and practical tips
2 Environmental information
1.These numbers indicate step by step how to use the appliance.
2.
3.
These operating instructions contain information on steps you can take
yourself to rectify a possible malfunction. Refer to the section “What to
do if...”.
In the event of any technical problems please contact your nearest cus-
tomer service centre at any time. (Addresses and telephone numbers
may be found in the appendix under "Customer Service Centres“).
You should also refer to the section "Service".
Printed on recycled paper.
Thinking ecologically means acting ecologically …
37
Contents
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
The Key Features of Your Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Description of the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cooking zones and control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Digital Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cooking Zone Safety Cut-out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Before Using for the First Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Initial Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Operating the Hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Touch Control Sensor Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Switching On the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Switching Off the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Cooking Zone Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Heat Setting Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Keep Warm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Switching the Triple Ring Cooking Zone On and Off. . . . . . . . . . . . . . . . . . . 48
Switching the Casserole Zone On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Stop+Go Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Switching off a Cooking Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Residual Heat Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cooking with the Automatic Warm up Function . . . . . . . . . . . . . . . . . . . . . . 53
Cooking without the Automatic Warm up Function . . . . . . . . . . . . . . . . . . . 54
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Uses, Tables and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Advice on Cooking with and without Automatic Warm up . . . . . . . . . . . . . 58
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Hob Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Rectifying faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
38
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Regulations, Standards, Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Safety Instructions for the Installer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Electrical Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
39
Operating Instructions
1 Safety
The safety aspects of this appliance comply with accepted technical
standards and the German Appliance Safety Law. However, as manufac-
turers we also believe it is our responsibility to familiarise you with the
following safety instructions.
Electrical Safety
The installation and connection of the new appliance must only be
carried out by qualified personnel.
Repairs to the appliance are only to be carried out by approved serv-
ice engineers. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. If your appliance needs repairing,
please contact your local customer center or your dealer.
3 Please follow these instructions, otherwise the warranty will not cover
any damage that may occur.
Flush-mounted appliances may only be operated following installa-
tion in suitable installation cabinets and workplaces which conform
to the relevant standards. This ensures sufficient protection against
contact for electrical units as required by the VDE [Association of
German Electrical Engineers].
If your appliance malfunctions or if fractures, cracks or splits appear:
switch off all cooking zones,
disconnect the hob from the electricity supply.
Child Safety
The cooking zones will become hot when you cook. Therefore, always
keep small children away from the appliance.
Safety During Use
This appliance may only be used for normal cooking and frying in the
home. It is not designed for commercial or industrial purposes.
Do not use the hob to heat the room.
Take care when plugging electric appliances into mains sockets near
the hob. Connection leads must not come into contact with the hot
surface.
40
Overheated fats and oils catch fire quickly. You should supervise
cooking when preparing foods in fat or oil (e.g. chips).
Switch off the cooking zones after use.
Safety When Cleaning
For safety reasons do not clean the appliance with a steam jet or high
pressure cleaner.
Clean the hob in accordance with the maintenance and cleaning in-
structions in this manual.
To Avoid Damaging Your Appliance
Do not use the hob as a work surface or for storage.
Do not operate the cooking zones when there is no pan or the pans
are empty.
Ceramic glass is insensitve to temperature shock and very robust;
however it is not unbreakable. Especially sharp and hard objects that
fall on the cooking surface can damage it.
Do not use cast iron pans or pans with a rough, burred or damaged
base. Scratching may occur if the pans are slid across the surface.
Do not place any pans on the hob frame. Scratching and damage to
the paint may occur.
Make sure that no acidic liquids, e.g. vinegar, lemon or descaling
agents, are spilt onto the hob frame, since these cause dull spots.
If sugar or a preparation with sugar comes into contact with the hot
cooking zone and melts there it must be cleaned off immediately
with a scraper while it is still hot. If it cools, the surface may be dam-
aged when it is removed.
Keep all items and materials that can melt away from the ceramic
glass surface, e.g. plastics, aluminium foil, or oven foils. If something
of this nature should melt onto the ceramic glass surface, it must also
be removed immediately using the scraper.
41
2 Disposal
Disposing of the packaging material
All materials used can be fully recycled.
Plastics are marked as follows:
>PE< for polyethylene, as used for the outer wrapping and the bags
inside.
>PS< for polystyrene foam, e.g., as used for the padding materials.
They are completely free of CFCs.
Disposal of old appliances
1 Warning: Before disposing of old appliances please make them inoper-
able so that they cannot be the source of danger.
To do this, disconnect the appliance from the mains supply and re-
move the mains lead.
To protect the environment, it is important that worn out appliances
are disposed of in the correct manner.
The appliance must not be disposed of with household rubbish.
You can obtain information about collection dates or public refuse
disposal sites from your local refuse department or council.
42
The Key Features of Your Appliance
Ceramic glass cooking surface: The appliance has a ceramic glass
cooking surface and 4 rapid response cooking zones. The particularly
powerful radiant heater elements significantly shorten the amount of
time taken for the zones to heat up.
Sensor fields: Your appliance is operated using Touch Control sensor
fields.
Cleaning: The advantage of the ceramic glass cooking surface and
the sensor fields is their accessibility for cleaning. The smooth, flat
surface is easy to clean.
On/Off sensor field: The “On/Off” sensor field provides the appliance
with a separate mains switch. Touching this switches the power sup-
ply on or off completely.
Control and function indicators: Digital indicators or control lamp
provide information about settings made, functions activated, as well
as any residual heat of the corresponding cooking zone.
Safety cut-out: A safety cut-out ensures that all cooking zones
switch off automatically after a period of time if the setting has not
been changed.
Keep Warm: u this setting is used for keeping food warm.
Stop+Go sensor field: Touching this sensor field changes all cooking
zones currently in use to the ”keep warm“ function: touching the
field again restores the zones to their former settings. This function
can be useful in certain situations, for example if you are suddenly
called away from the cooker.
Residual heat indicator: An h for residual heat is shown in the dis-
play if the cooking zone becomes so hot that there is a risk of burn-
ing.
Multipurpose cooking zone: The hob is equipped with a multipur-
pose/casserole cooking zone. Depending on the setting, it can be used
as a round or oval cooking zone, e.g. for oval casseroles or for keeping
dishes or food warm.
Triple ring cooking zone: The hob features a triple-ring cooking
zone. This zone can be set to different sizes, for example to fit smaller
pots. This will save power.
Timer: All zones can be automatically switched off using the inte-
grated timer. When the end of the cooking time has been reached,
the cooking zone switches off.
43
Description of the Appliance
Cooking zones and control panel
Triple ring cooking zone
2300W
Single ring cooking zone
1200W
Single ring cooking zone
1200W
Control panel
Casserole zone
2400W
Cooking zone selection with
displays for heat setting/
residual heat
Booster button
Mains button
On/Off
Heat setting
selector
”Stop+Go“
button
„Timer“ with control display
Casserole zone indicator
Triple ring
indicator
44
Digital Display
The four display fields correspond to the four cooking zones, and give
the following indications:
_ when switched on, and when switched off automatically by the
safety function,
0 when a cooking zone is selected,
u when the Keep Warm setting is selected,
1 to 9, depending on the selected Cook setting,
a when Automatic Warm Up is on,
h when Residual Heat is on,
f if there is a fault.
1 Cooking Zone Safety Cut-out
If one of the cooking zones is not switched off after a certain time or if
the heat setting is not changed, the corresponding cooking zone
switches itself off automatically.
h appears in the ring display for all rings that are switched on, and _
after they have cooled down.
The rings are switched off at:
3 If one or more cooking zones switch off before the times indicated see
section “What to do if …”.
Cancelling the Safety Cut-out
To cancel the activated safety cut-out the appliance must be switched
off and then on again using the ON/OFF I sensor field. After this the
cooking zones are again ready for use.
Switching Off for Other Reasons
Liquid that boils over onto the control panel causes all cooking zones to
switch off immediately.
If you place a wet cloth on the control panel it has the same effect. In
both cases the appliance has to be switched on again using the mains
switch I after removing the liquid or cloth.
Heat setting 1 - 2 after 6 hours
Heat setting 3 - 4 after 5 hours
Heat setting 5 after 4 hours
Heat setting 6 - 9 after 1.5 hours
45
Before Using for the First Timeme
Initial Cleaning
Wipe the ceramic glass surface with a damp cloth.
1 Important: Do not use any caustic, abrasive cleaners! The surface could
be damaged.
Operating the Hob
3
When a cooking zone is switched on, it may hum briefly. This is a char-
acteristic of all ceramic glass cooking zones and does not impair either
the function or the life of the appliance.
Touch Control Sensor Field
To operate the Touch Control sensor field place your finger from above
flat onto the required field until the appropriate displays come on or go
out or the required function is carried out.
Switching On the Appliance
The entire appliance is switched on using the “On/Off” I sensor field.
Touch the “On/Off” sensor field for approx. 2 seconds.
The digital displays will show _ and the decimal point will flash.
3 Once the “On/Off” sensor field has been operated to switch on the ap-
pliance, one of the cooking zones must be selected within approx.
10 seconds using the cooking zone selection buttons. Otherwise the ap-
pliance switches off again for safety reasons.
46
Switching Off the Appliance
To switch off the appliance completely activate the “On/Off” I sensor
field.
Touch the “On/Off” sensor field for approx. 1 second.
3 When an individual cooking zone or the entire hob is switched off, any
residual heat is shown with an h (for “Hot”) in the digital display for
the appropriate cooking zones.
Cooking Zone Selection
To select the required cooking zone touch the corresponding sensor
field for approx. one second.
A zero with a decimal point will light up in the appropriate cooking
zone display window 0.
3 The decimal point indicates that settings may only be made for this
cooking zone.
47
Heat Setting Selection
For setting and adjusting the heat setting (u to 9) for the selected
cooking zone.
Use sensor field + to increase the heat setting.
Lower the heat setting with sensor field -.
3 If several cooking zones are being used simultaneously, the required
cooking zone must be selected by touching the appropriate sensor field
before adjusting the heat setting. The decimal point in the display
shows which cooking zone has been selected.
Keep Warm
The ”keep warm“ function u can be used with all four cooking zones.
1.Select the desired cooking zone using the sensor fields.
2.Using the + sensor field, select the ”keep warm“ u setting.
3 The ”keep warm“ setting is limited to 60 minutes, i.e. after this time the
cooking zone is finally switched off.
48
Switching the Triple Ring Cooking Zone On and Off
Depending on the size of the pot or pan, when using the triple ring
cooking zone each of the larger cooking rings can be switched on in
turn, in addition to the smallest cooking zone, using the “booster” sen-
sor field on the control panel.
3 These can only be activiated if the smaller ring is already switched on.
1.Select the appropriate cooking zone.
2.Set the required heat setting.
3.Touch the “booster” sensor field.
49
The middle ring is switched on. The control indicator under the
symbol II is illuminated.
4.Touching the “booster” sensor field again activates the outer heating
ring. The control indicator under symbol III is illuminated.
5.To switch off the outer heating rings touch the “booster” sensor field;
the corresponding outer heating ring is switched off.
50
Switching the Casserole Zone On and Off
1.Select the appropriate cooking zone.
2.Set the required heat setting.
3.To switch the casserole zone on or off place your finger flat on the
“booster” touch control sensor field, until the control indicator comes
on or goes off.
51
Stop+Go Function
By touching the "Stop+Go" sensor field, all cooking zones in use can be
switched simultaneously to the "keep warm“ setting. The "keep warm“
setting is indicated on the display by a u
symbol.
If the "Stop+Go" sensor field is touched again, the previously selected
settings are restored.
3 The Timer is unaffected by the "Stop+Go" function.
If an automatic warm-up function was selected with warm-up
phase a, this is stopped by the "Stop+Go" function , and is re-started
when the "Stop+Go" sensor field is pressed again.
The "keep warm“ function is limited to 60 minutes, i.e. after this time
the cooking zone is finally switched off.
52
Switching off a Cooking Zone
1.Select the required cooking zone with the cooking zone sensor fields.
2.Touch sensor fields + and - simultaneously to switch off or turn sen-
sor field - back to zero.
3 A cooking zone may only be switched off when the decimal point is on
in the cooking zone display.
Residual Heat Indicator
When an individual cooking zone or the entire hob is
switched off, any residual heat is shown with an h (for
“Hot”) in the digital display for the appropriate cooking
zones.
Even after the cooking zone has been switched off, the
residual heat indicator only goes out when the cooking zone is cold.
2 You can use the residual heat for melting and keeping food warm.
1 Important! As long as the residual heat indicator is illuminated, there
is a risk of burns.
1 Important! If the power supply is interrupted the h symbol will also
go out and information about residual heat will no longer be available.
However, it may still be possible to burn yourself. This can be avoided
by taking care when near the hob.
53
Cooking with the Automatic Warm up Function
All four of the hob's cooking zones can be controlled in nine stages and
have an automatic warm up function:
1, lowest heat setting
9, highest heat setting
a, automatic warm up function
When you select the required heat setting using the + sensor field, the
cooking zone will work for a specific time on full power and then
switch automatically to the set heat setting.
The duration of the automatic warm up function depends on the heat
setting selected.
Select the required cooking zone with the cooking zone sensor fields.
Touch sensor field + until it reaches the required heat 1 to 8. The set
heat setting will be displayed first. After five seconds a (= automatic
warm up function) will replace the heat setting in the display. At the
end of the warm up time the heat setting will be shown again.
3 If during the automatic warm up function you select a higher setting,
eg. from 3 to 5, the warm up time is adjusted to match. If you select a
lower setting, the warm up time ends at once.
54
2 If you start cooking again on a cooking zone that is still warm, the au-
tomatic warm up function uses the residual heat. This saves time and
energy.
3 If you again wish to switch on a cooking zone on which hot items are
already standing, you should always select the required heat setting
with the - sensor field. In this way you can avoid making the food boil
over as a result of the extra burst of heat from the automatic warm up.
Cooking without the Automatic Warm up Function
If you wish to use the cooking zone without automatic warm up, select
the required heat setting with the - sensor field.
1.Switch on the appliance and select the desired cooking zone using the
cooking zone selection buttons.
2.Touch sensor field - to select the required heat setting from 9 to 1.
3 You can adjust the heat setting at any time using the + and - but-
tons, providing the cooking zone has been selected.
Switching off a cooking zone
1.Select the desired cooking zone using the cooking zone buttons.
2.Press the + and - buttons simultaneously to switch off.
1 When the rings are still hot cooking should be carried out without au-
tomatic warm up.
1 / 1

AEG 75301K-MN User manual

Category
Hobs
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document