Heat & Glo LifeStyle SL-750TRS-IPI-D User manual

Brand: Heat & Glo LifeStyle

Model: SL-750TRS-IPI-D

Category: Fireplaces

Type: User manual

This manual is also suitable for

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Models:

SL-750TRS-IPI-D

SL-550TRS-IPI-D

SL-350TRS-C

Owner’s Manual

Installation and Operation

• Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or

any other appliance.

• What to do if you smell gas

- Do not try to light any appliance

- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed by

a qualified installer, service agency, or the gas

supplier.

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing proper-

ty damage, personal injury, or death.

This appliance has been supplied with an integral barrier

to prevent direct contact with the fixed glass panel. Do

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT.

CLOTHING IGNITION MAY RESULT.

WARNING

• Keep children away.

• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high

temperatures.

• Do NOT operate with protective barriers open or

removed.

• Keep clothing, furniture, draperies and other

combustibles away.

Glass and other surfaces are hot during

operation and cool down.

DO NOT DISCARD THIS MANUAL

CAUTION

Important operating and

maintenance instruc-

tions included.

This appliance may be installed as an OEM installation in

manufactured home (USA only) or mobile home and must

be installed in accordance with the manufacturer’s instruc-

tions and the manufactured home construction and safety

standard, Title 24 CFR, Part 3280 or Standard for Installa-

tion in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indi-

cated on the rating plate.

Installation and service of this appliance should be

performed by qualified personnel. Hearth & Home

Technologies suggests NFI certified or factory-trained

professionals, or technicians supervised

by an NFI certified professional.

•

••

DO NODO NO

DO NO

DISCARDDISCARD

DISCARD

Read, understand and follow

these instructions for safe

installation and operation.

Leave this manual with

party responsible for

use and operation.

In the Commonwealth of Massachusetts:

• installation must be performed by a licensed plumber or

gas fitter;

See Table of Contents for location of additional

Commonwealth of Massachusetts requirements.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

These units MUST use one of the vent systems

described in the Installing the Appliance section of

the Installers Guide. NO OTHER vent systems or

components MAY BE USED.

This gas appliance and vent assembly MUST be

vented directly to the outside and MUST NEVER be

attached to a chimney serving a separate solid fuel

burning appliance. Each gas appliance MUST USE

a separate vent system. Common vent systems are

PROHIBITED.

INSPECT the external vent cap on a regular basis to

make sure that no debris is interfering with the air

flow.

The glass door assembly MUST be in place and

sealed, and the trim door assembly MUST be in

place on the appliance before the unit can be

placed into safe operation.

DO NOT OPERATE this appliance with the glass

door removed, cracked, or broken. Replacement of

the glass door should be performed by a licensed

or qualified service person. DO NOT strike or slam

the glass door.

The glass door assembly SHALL ONLY be

replaced as a complete unit, as supplied by the gas

appliance manufacturer. NO SUBSTITUTE material

may be used.

DO NOT USE abrasive cleaners on the glass door

assembly. DO NOT ATTEMPT to clean the glass

door when it is hot.

Turn off the gas before servicing this appliance. It is

recommended that a qualified service technician

perform an appliance check-up at the beginning of

each heating season.

Any safety screen or guard removed for servicing

must be replaced before operating this appliance.

DO NOT place furniture or any other combustible

household objects within 36 inches of the

appliance front.

READ and UNDERSTAND all instructions carefully

before starting the installation. FAILURE TO

FOLLOW these installation instructions may result

in a possible fire hazard and will void the warranty.

Prior to the first firing of the appliance, READ the

Using Your Appliance section of the Owners Guide.

DO NOT USE this appliance if any part has been

under water. Immediately CALL a qualified service

technician to inspect the unit and to replace any part

of the control system and any gas control which has

been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a

qualified service person. The appliance and venting

system should be INSPECTED before initial use

and at least annually by a professional service

person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding

material, etc. It is IMPERATIVE that the unit’s

control compartment, burners, and circulating air

passageways

BE KEPT CLEAN to provide for

adequate combustion and ventilation air.

Always KEEP the appliance clear and free from

combustible materials, gasoline, and other

flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and

ventilation air. Keep the front of the appliance

CLEAR of all obstacles and materials for servicing

and proper operations.

Due to the high temperature, the appliance should

be LOCATED out of traffic areas and away from

furniture and draperies. Clothing or flammable

material SHOULD NOT BE PLACED on or near the

appliance.

Children and adults should be ALERTED to the

hazards of high surface temperature and should

STAY AWAY to avoid burns or clothing ignition.

Young children should be CAREFULLY SUPERVISED

when they are in the same room as the appliance.

SAFETY AND WARNING INFORMATION

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

TABLE OF CONTENTS

Safety and Warning Information ......................................................... 2

Service Parts Lists ................................................................................. 4

Section 1: Approvals and Codes........................................................ 12

Appliance Certification ........................................................................... 12

Installation Codes .................................................................................. 12

High Altitude Installations ...................................................................... 12

Requirements for the Commonwealth of Massachusetts........................ 13

Section 2: Getting Started .................................................................. 14

Introducing the Heat & Glo Gas Appliances ........................................... 14

Pre-installation Preparation .................................................................... 14

Section 3: Installing the Appliance ................................................... 18

Constructing the Appliance Chase ......................................................... 18

Step 1 Locating the Appliance.......................................................... 18

Step 2 Framing the Appliance .......................................................... 19

Step 3 Installing the Vent System .................................................... 22

A. Vent System Approvals ................................................... 22

B. Installing Vent Components............................................. 32

C. Vent Termination.............................................................. 35

Step 4 Positioning, Leveling, and

Securing the Appliance ......................................................... 38

Step 5 The Gas Control Systems..................................................... 38

Step 6 The Gas Supply Line............................................................. 39

Step 7 Gas Pressure Requirements ................................................. 39

Step 8 Wiring the Appliance ............................................................. 40

Step 9 Finishing ............................................................................... 42

Step 10 Installing Trim, Logs, and Ember Material ............................. 43

Installing the Trim.................................................................. 43

Positioning the Logs ............................................................. 43

Shutter Settings.................................................................... 43

Placing the Ember Material................................................... 43

Glass Specifications ............................................................. 43

Step 11 Before Lighting the Appliance ................................................ 44

Step 12 Lighting the Appliance ........................................................... 44

After the Installation ............................................................................... 44

Section 4: Maintaining and Servicing Your Appliance ................... 45

Î = Contains updated information.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Exploded Parts Diagram

Service Parts

SL-350TRS-C

Beginning Manufacturing Date: 4-01

Ending Manufacturing Date: ______

Part number list on following page.

7 Log Set Assembly

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Service Parts List

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order-

ing, supply serial and model numbers to ensure correct service parts.

SL-350TRS-C

ITEM STANDING PILOT SERIAL # PART NUMBER

Burner Orifice NG (#43C) 582-843

Burner Orifice LP (#53C) 582-853

1 Glass Door Assembly GLA-350TRS

2Burner NG, LP 540-234A

3 Mesh Panel Door 540-382A

4 Log Grate 540-361A

5 Base Refractory

PRE 4/06

POST 4/06

540-206T (Tan)

2065-206 (Black)

6 Hood SRV540-174

7 Log Set Assembly LOGS-350

8 Log 1 SRV530-701

9 Log 2 SRV530-704

10 Log 3 SRV540-702

11 Log 4 SRV530-705

12 Log 5 SRV530-703

13 Junction Box

PRE 00251404

POST 00251404

100-250A

4021-013

14 Louver, Top 540-256A

15 Louver, Bottom 540-257A

Pilot Orifice NG 446-505

Pilot Orifice LP 446-517

Thermocouple 446-511

Thermopile 060-512

Conversion Kit NG NGK-350TRS-C

Conversion Kit LP LPK-350TRS-C

Vermiculite Embers MYSTIC-EMBERS

Exhaust Restrictor 530-299

Glass Latch Assembly 386-122A

Mineral Wool 050-721

Touch up Paint TUP-GBK-12

Also see additional pages for valve assembly service part numbers.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Exploded Parts Diagram

Service Parts

Beginning Manufacturing Date: 4-01

Ending Manufacturing Date: ______

SL-350TRS-C

ITEM DESCRIPTION SERIAL # PART NUMBER

1Piezo Ignitor 291-513

2 Burner Neck Gasket 2045-407

3 Thermostat Wire Assembly

PRE 00251404

POST 00251404

N/A

2045-024

4 Pilot Assembly NG 530-510A

4 Pilot Assembly LP 530-511A

5 Valve Bracket 2025-101

6 Valve Plate Gasket 530-431

7 Flex Ball Valve Assembly 302-320A

8Valve NG 060-522

8 Valve LP 060-523

9 Flexible Gas Connector

PRE 22099930

POST 22099930

567-301A

530-302A

10 Pilot Bracket 530-164

ON/OFF Rocker Switch

PRE 00251404

POST 00251404

060-511

N/A

Wire Assembly

PRE 00251404

POST 00251404

049-552A

N/A

Standing Pilot Ignition

Valve Assembly

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Exploded Parts Diagram

Service Parts

SL-550TRS-IPI-D

Beginning Manufacturing Date: 4-04

Ending Manufacturing Date: ______

7 Log Set Assembly

Part number list on following page.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Service Parts List

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering,

supply serial and model numbers to ensure correct service parts.

SL-550TRS-IPI-D

ITEM DESCRIPTION SERIAL # PART NUMBER

Burner Orifice NG (#38C) 582-838

Burner Orifice LP (#53C) 582-853

1 Junction Box 4021-013

2Burner NG 2065-005

2Burner LP 2065-006

3 Glass Door Assembly GLA-550TRS

4 Log Grate 2066-036

5 Base Refractory NG, LP 2065-100

6 Hood SRV550-175

7 Log Set Assembly LOGS-550TRS-D

8 Log 1 SRV2065-701

9 Log 2 SRV2065-702

10 Log 3 SRV2065-703

11 Log 4 SRV2065-704

12 Log 5 SRV2065-705

Refractory Kit BRICK-550TRS-D

13 Refractory, Back SRV2044-711

14 Refractory, Left Side SRV2044-710

15 Refractory, Right Side SRV2044-712

Pilot Orifice NG 446-505

Pilot Orifice LP 446-517

Thermocouple 446-511

Thermopile 060-512

Mineral Wool 050-721

Glass Latch 386-122A

Exhaust Restrictor 530-299

Touch up Paint TUP-GBK-12

ACCESSORIES

Fan Kit GFK-160A

Extended Vertical Baffle Kit BAF-VERT

Wall Switch Kit, Off-white WSK-21

Wall Switch Kit, White WSK-21-W

Conversion Kit NG NGK-550TRS-IPID

Conversion Kit LP LPK-550TRS-IPID

Vermiculite Embers MYSTIC-EMBERS

Also see additional pages for valve assembly service part numbers.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Exploded Parts Diagram

Service Parts

SL-750TRS-IPI-D

Beginning Manufacturing Date: 4-04

Ending Manufacturing Date: ______

Part number list on following page.

7 Log Set Assembly

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Service Parts List

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order-

ing, supply serial and model numbers to ensure correct service parts.

SL-750TRS-IPI-D

ITEM DESCRIPTION SERIAL # PART NUMBER

Burner Orifice NG (#36C) 582-836

Burner Orifice LP (#52C) 582-852

1 Junction Box 4021-013

2 Burner NG 2066-005

2 Burner LP 2065-006

3 Glass Door Assembly GLA-750TRS

4 Log Grate 2066-036

5 Base Refractory NG, LP 2066-100

6 Hood SRV530-175

7 Log Set Assembly LOGS-750TRS-D

8 Log 1 SRV2065-701

9 Log 2 SRV2066-702

10 Log 3 SRV2066-703

11 Log 4 SRV2066-704

12 Log 5 SRV2066-705

Refractory Kit BRICK-750TRS-D

13 Refractory, Back SRV2045-711

14 Refractory, Left Side SRV2045-710

15 Refractory, Right Side SRV2045-712

Mineral Wool 050-721

Glass Latch Assembly 386-122A

Exhaust Restrictor 530-299

Touch up Paint TUP-GBK-12

ACCESSORIES

Fan Kit GFK-160A

Extended Vertical Baffle Kit BAF-VERT

Wall Switch Kit, Off-white WSK-21

Wall Switch Kit, White WSK-21-W

Conversion Kit NG NGK-750TRS-IPID

Conversion Kit LP LPK-750TRS-IPID

Vermiculite Embers MYSTIC-EMBERS

Also see additional pages for valve assembly service part numbers.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

(NG, LP) Exploded Parts Diagram

Service Parts

Beginning Manufacturing Date: 4-04

Ending Manufacturing Date: ______

SL-750TRS-IPI-D, SL-550TRS-IPI-D

ITEM /

PIÈCE

DESCRIPTION

SERIAL #

/ N° DE SÉRIE

PART NUMBER

/ N° DE PIÈCE

1 Burner Neck Gasket / Joint de Cou de Brûleur 2045-407

2 Thermostat Wire Assembly / L'Assemblée de Fil de thermostat 2045-024

3 Wire Assembly / Module de fil 2012-206

4 Pilot Assembly NG / Module de veilleuse GN 4021-025

4 Pilot Assembly LP / Module de veilleuse PL 4021-026

5 Valve Bracket / Parenthèse de Valve 2025-101

6 Ground Strap / Courroie de Raison(Terre) 385-512

7 Flex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle 302-320A

8Valve NG / Valve GN 750-500

8 Valve LP / Valve PL 750-501

9 Flexible Gas Connector / Tuyau à gaz flexible 530-302A

10 Module / Module 593-592

11 Wire Assembly / Module de fil 593-590A

12 Battery Pack / Paquet de Batterie(Pile) 593-594A

13 3 Volt Transformer / 3 Transformateur de Volt 593-593A

14 Valve Plate Gasket / Joint de Plat de Valve 530-431

15 Pilot Bracket / Parenthèse Pilote 2065-117

Intermittent Pilot Ignition

Valve Assembly

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Approvals and

Codes

Heat & Glo Quality

Systems registered

by SGS ICS

Appliance Certification

The Heat & Glo appliance models discussed in this Installers

Guide have been tested to certification standards and listed

by the applicable laboratories.

Certification

MODELS: SL-750TRS-IPI-D, SL-550TRS-IPI-D,

SL-350TRS-C

LABORATORY: Underwriters Laboratories

TYPE: Direct Vent Gas Fireplace Heater

STANDARD: ANSI Z21.88•CSA2.33•UL307B

High Altitude Installations

U.L. Listed gas appliances are tested and approved with-

out requiring changes for elevations from 0 to 2,000 feet in

the U. S. A. and in Canada.

When installing this appliance at an elevation above 2,000

feet, it may be necessary to decrease the input rating by

changing the existing burner orifice to a smaller size. Input

rate should be reduced by 4% for each 1000 feet above a

2000 foot elevation in the U.S.A. or 10% for elevations

between 2000 and 4500 feet in Canada. If the heating value

of the gas has been reduced, these rules do not apply. To

identify the proper orifice size, check with the local gas

utility.

If installing this appliance at an elevation above 4,500 feet

(in Canada), check with local authorities.

NOTE: THESE MODELS ARE UL LISTED TO UL307B,

THE STANDARD FOR GAS-BURNING HEATING APPLI-

ANCES FOR MANUFACTURED HOMES AND RECRE-

ATIONAL VEHICLES.

Installation Codes

The appliance installation must conform to local codes.

Before installing the appliance, consult the local building

code agency to ensure that you are in compliance with all

applicable codes, including permits and inspections.

In the absence of local codes, the appliance installation

must conform to the National Fuel Gas Code ANSI Z223.1

(in the United States) or the CAN/CGA-B149 Installation

Codes (in Canada). The appliance must be electrically

grounded in accordance with local codes or, in the absence

of local codes with the National Electric Code ANSI/NFPA

No. 70 (in the United States), or to the CSA C22.1 Canadian

Electric Code (in Canada).

These models may be installed in a bedroom or bed-sitting

room in the U.S.A. and Canada.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven (7)

feet above finished grade in the area of the venting, includ-

ing but not limited to decks and porches, the following re-

quirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gasfitter

shall observe that a hard wired carbon monoxide detector

with an alarm and battery back-up is installed on the floor

level where the gas equipment is to be installed. In addi-

tion, the installing plumber or gasfitter shall observe that a

battery operated or hard wired carbon monoxide detector

with an alarm is installed on each additional level of the

dwelling, building or structure served by the side wall hori-

zontal vented gas fueled equipment. It shall be the respon-

sibility of the property owner to secure the services of qual-

ified licensed professionals for the installation of hard wired

carbon monoxide detectors.

In the event that the side wall horizontally vented gas fu-

eled equipment is installed in a crawl space or an attic, the

hard wired carbon monoxide detector with alarm and bat-

tery back-up may be installed on the next adjacent floor

level.

In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the

owner shall have a period of thirty (30) days to comply with

the above requirements; provided, however, that during said

thirty (30) day period, a battery operated carbon monoxide

detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance

with the above provisions shall comply with NFPA 720 and

be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently

mounted to the exterior of the building at a minimum height

of eight (8) feet above grade directly in line with the ex-

haust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in

print size no less than one-half (1/2) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-

STRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally

vented gas fueled equipment shall not approve the installa-

tion unless, upon inspection, the inspector observes carbon

monoxide detectors and signage installed in accordance with

the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1

through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition

of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure sepa-

rate from the dwelling, building or structure used in whole

or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall hor-

izontally vented gas equipment provides a venting system

design or venting system components with the equipment,

the instructions provided by the manufacturer for installa-

tion of the equipment and the venting system shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall

horizontally vented gas fueled equipment does not provide

the parts for venting the flue gases, but identifies “special

venting systems”, the following requirements shall be sat-

isfied by the manufacturer:

• The referenced “special venting system” instructions shall

be included with the appliance or equipment installation

instructions; and

• The “special venting systems” shall be Product Approved

by the Board, and the instructions for that system shall

include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Ap-

proved side wall horizontally vented gas fueled equipment,

all venting instructions, all parts lists for venting instruc-

tions, and/or all venting design instructions shall remain

with the appliance or equipment at the completion of the

installation.

See Gas Connection section for additional Common-

wealth of Massachusetts requirements.

NOTE: The following requirements reference various

Massachusetts and national codes not contained in

this document.

Requirements for the Commonwealth of

Massachusetts

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Getting Started

Introducing the Heat & Glo Gas Appliances

Heat & Glo direct vent gas appliances are designed to op-

erate with all combustion air siphoned from outside of the

building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless

noted otherwise, applies to all models and gas control

systems. Gas appliance diagrams, including the dimensions,

are shown in this section.

Pre-install Preparation

This gas appliance and its components are tested and safe

when installed in accordance with this Installers Guide.

Report to your dealer any parts damaged in shipment,

particularly the condition of the glass. Do not install any

unit with damaged, incomplete, or substitute parts.

The vent system components and trim doors are shipped

in separate packages. The gas logs are packaged

separately and must be field installed.

Read all of the instructions before starting the

installation. Follow these instructions carefully during

the installation to ensure maximum safety and benefit.

Failure to follow these instructions will void the

owner’s warranty and may present a fire hazard.

The Heat & Glo Warranty will be voided by, and Heat & Glo

disclaims any responsibility for, the following actions:

• Installation of any damaged appliance or vent system

component.

• Modification of the appliance or direct vent system.

• Installation other than as instructed by Heat & Glo.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not manu-

factured and approved by Heat & Glo, not withstanding

any independent testing laboratory or other party approval

of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE

HAZARD.

When planning a appliance installation, it’s necessary to

determine:

• Where the unit is to be installed.

• The vent system configuration to be used.

• Gas supply piping.

• Electrical wiring.

• Framing and finishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

If the appliance is to be installed on carpeting or tile, or on

any combustible material other than wood flooring, the

appliance should be installed on a metal or wood panel that

extends the full width and depth of the appliance.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Figure 1. Diagram of the SL-750TRS-IPI-D

HOOD

GAS

CONTROLS

GAS LINE

ACCESS

VENT COLLARS

TOP STANDOFFS

ELECTRICAL

ACCESS

RATING PLATES

& LABELS

BOTTOM GRILLE

COVER

CERAMIC

FIBER PAD

37-7/8

962[]

3-9/16

[]

6-7/8

175[]

35-5/8

905[]

1041.4[]

36-1/8

918[]

5-1/2

140[]

2-1/4

57[]

152[]

1016[]

8-3/4

222[]

16-1/4

413[]

1/2

13[]

15-7/8

403[]

15-3/8

391[]

30-3/4

781[]

ø6-5/8

168.3[]

GASS LINE

ACCESS

ELECTRICAL

ACCESS

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Figure 2. Diagram of the SL-550TRS-IPI-D

32-9/16

827

[]

3-1/2

[

]

6-7/8

174[]

914[]

31-1/8

791

[

]

32-1/8

816[

]

5-1/2

140[

]

2-1/8

54[

]

152[]

35-7/16

900.1[

]

ø6-5/8

168.3

[

]

8-13/16

224[

]

16-1/4

413[

]

1/2

13[

]

15-7/8

403[

]

12-7/8

327[

]

25-3/4

654[

]

ELECTRICAL

ACCESS

ø 8

GAS LINE

ACCESS

168.3[

]

HOOD

GAS

CONTROLS

GAS LINE

ACCESS

VENT COLLARS

TOP STANDOFF

ELECTRICAL

ACCESS

RATING PLATES

& LABELS

BOTTOM GRILLE

COVER

CERAMIC

FIBER PAD

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Figure 3. Diagram of the SL-350TRS-C

6-7/8

174[]

3-1/2

90[]

30-5/8

777[]

21-1/4

540[]

737[]

15-1/4

388[]

28-1/8

714[]

836[]

30-1/2

776[]

2-1/8

55[]

153[]

1/2

13[]

16-1/4

413[]

8-3/4

223[]

15-7/8

402[]

22-3/4 577[]

11-3/8

289[]

ø6-5/8

168.3[]

34-1/2

876[]

ø8 [203]

ELECTRICAL

ACCESS

GAS LINE

ACCESS

HOOD

GAS

CONTROLS

GAS LINE

ACCESS

VENT COLLARS

TOP STANDOFFS

ELECTRICAL

ACCESS

RATING PLATES

& LABELS

BOTTOM GRILLE

COVER

CERAMIC

FIBER PAD

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Installing the Appliance

Step 1. Locating the Appliance

Space and clearance requirements for locating a appliance

within a room (see Figure 4).

Minimum Clearances

from the Appliance to Combustible Materials

For minimum clearances, see the direct vent termination

clearance diagrams in Figures 29 and 30 in this manual.

Minimum Clearances

from the Vent Pipe to Combustible Materials

Inches mm

Vertical Sections. ............. 1 ................ 25

Horizontal Sections

Top..................................... 3 ................ 75

Bottom ............................... 1 ................ 25

Sides ................................. 1 ................ 25

At Wall Firestops

Top .................................. 2 1/2 ............63.7

Bottom ..............................1/2............... 13

Sides ................................. 1 ................ 25

* The clearance to the ceiling is measured from the top

of the unit, excluding the standoffs (see Figure 37).

The distance from the unit to combustible construction is to

be measured from the unit outer wrap surface to the com-

bustible construction, NOT from the screw heads that se-

cure the unit together.

1/2 “ MIN. (13mm)

3” MIN. (76mm)

Clearance Requirements

The top and back of the appliance are defined by stand-

offs. The minimum clearance to a perpendicular wall

extending past the face of the appliance is 3 inches (76mm).

The back of the appliance may be recessed 16 1/4 inches

(413mm) into combustible construction.

Figure 4. Appliance Dimensions, Locations,

and Space Requirements

Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the

gas appliance and/or its vent system. Vertical vents that run

on the outside of a building may be, but are not required to

be, installed inside a chase.

CAUTION: TREATMENT OF FIRESTOP SPACERS AND

CONSTRUCTION OF THE CHASE MAY VARY WITH THE

TYPE OF BUILDING. THESE INSTRUCTIONS ARE NOT

SUBSTITUTES FOR THE REQUIREMENTS OF LOCAL

BUILDING CODES. THEREFORE, YOUR LOCAL BUILD-

ING CODES MUST BE CHECKED TO DETERMINE THE

REQUIREMENTS FOR THESE STEPS.

Factory-built appliance chases should be constructed in

the manner of all outside walls of the home to prevent cold

air drafting problems. The chase should not break the out-

side building envelope in any manner.

This means that the walls, ceiling, base plate and cantilever

floor of the chase should be insulated. Vapor and air infiltra-

tion barriers should be installed in the chase as per regional

codes for the rest of the home. Additionally, in regions where

cold air infiltration may be an issue, the inside surfaces

may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the firestops should be caulked to

seal gaps. Gas line holes and other openings should be

caulked or stuffed with insulation. If the unit is being in-

stalled on a cement slab, a layer of plywood may be placed

underneath to prevent conducting cold up into the room.

THE CHASE SHOULD BE CONSTRUCTED SO THAT ALL

CLEARANCES TO THE APPLIANCE ARE MAINTAINED

AS SPECIFIED WITHIN THIS INSTALLERS GUIDE.

Inches mm

Glass Front..........................................36.... 914

Floor .....................................................0....... 0

Rear .................................................... 1/2 .... 13

Sides .................................................. 1/2 .... 13

*Top (SL-750TRS-IPI-D) ..........................................3 1/4... 83

(SL-550TRS-IPI-D, SL-350TRS-C) ...................1 1/2... 38

Ceiling**...............................................31.... 787

*NOTE: If venting with (2) 90

elbows off rear of unit

the dimensions C, D, and E, will change.

MODEL VENT A B C D E

SL-750TRS-IPI-D

Top 42 16-1/4 31-7/8 45 63-3/4

Rear 42 16-1/4 36-5/8 52 73-1/4

SL-550TRS-IPI-D

Top 37 16-1/4 29-3/8 41-1/2 58-3/4

Rear 37 16-1/4 34-1/8 48-1/2 68-1/4

SL-350TRS-C

Top 34 16-1/4 27-7/8 39-3/8 55-5/8

Rear 34 16-1/4 32-5/8 46-3/8 65-1/8

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Figure 5. Framing Dimensions

Framing should be

constructed of 2 X 4

lumber or heavier.

The framing headers

may rest on the

appliance stand-offs.

Step 2. Framing the Appliance

Appliance framing can be built before or after the appliance

is set in place. Framing should be positioned to accommo-

date wall coverings and appliance facing material. The dia-

gram below shows framing reference dimensions.

CAUTION: MEASURE APPLIANCE DIMENSIONS AND

VERIFY FRAMING METHODS AND WALL COVERING

DETAILS BEFORE FRAMING.

VENT

FRAMING

HOLE

Models A B C D E

SL-750TRS-IPI-D 42” 38 1/4” 16 1/4” 41” 27 7/8”

SL-550TRS-IPI-D 37” 33” 16 1/4” 36 1/2” 24 3/8”

SL-350TRS-C 34” 31” 16 1/4” 35 1/2” 22 3/8”

WALL STUD

NON-COMBUSTIBLE ZONE

IS DEFINED BY 3” ABOVE THE

ELBOW FOR THE ENTIRE

WIDTH AND DEPTH (BEHIND THE

FRONT HEADER) OF THE FIREBOX.

3”

2-1/4”

*The center of the

framing hole is one (1)

inch (25.4mm) above

the center of the hori-

zontal vent pipe.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

NOTE: PIPES OVERLAP 1-1/4 INCHES

(34.93mm) AT EACH JOINT.

Figure 6. DVP-Series Direct Vent Component Specifications (5-inch inner pipe / 8-inch outer pipe)

12-9/16

11-1/4

7-1/4

1-1/4 TYP

1/2 TYP

8-9/16

DVP36

DVP48

DVP4

DVP6

DVP12

MIN.

DVP12A

12-3/16

MAX.

DVP24

9-7/8

45.0

10-1/4

DVP45

14-1/4

Page is loading ...

Heat & Glo LifeStyle SL-750TRS-IPI-D User manual

Brand: Heat & Glo LifeStyle

Model: SL-750TRS-IPI-D

Category: Fireplaces

Type: User manual

This manual is also suitable for

Download PDF

report

Heat & Glo LifeStyle SL-750TRS-IPI-D User manual

This manual is also suitable for

Heat & Glo LifeStyle SL-750TRS-IPI-D User manual

Related papers

Other documents