O P E R A T I N G I N S T R U C T I O N S
Flexi IO XTDI1
Expansion module - IO
FLX3-XTDI00S14
Described product
F
lexi IO XTDI1
Manufacturer
SIC
K AG
Erwin-Sick-Str. 1
79183 Waldkirch
Germany
Legal information
T
his work is protected by copyright. Any rights derived from the copyright shall be
reserved for SICK AG. Reproduction of this document or parts of this document is
only permissible within the limits of the legal determination of Copyright Law. Any modi‐
fication, abridgment or translation of this document is prohibited without the express
written permission of SICK AG.
The trademarks stated in this document are the property of their respective owner.
© SICK AG. All rights reserved.
Original document
T
his document is an original document of SICK AG.
2
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
Contents
1 Ordering information........................................................................ 5
1.1 Ordering information for main module.................................................... 5
1.2 Ordering information for expansion module........................................... 5
2 About this document........................................................................ 6
2.1 Purpose of this document........................................................................ 6
2.2 Scope......................................................................................................... 6
2.3 Target groups and structure of these operating instructions................ 6
2.4 Further information................................................................................... 6
2.5 Symbols and document conventions...................................................... 7
3 Safety information............................................................................ 8
3.1 General safety notes................................................................................ 8
3.2 Intended use............................................................................................. 8
3.3 Improper use............................................................................................. 8
3.4 Requirements for the qualification of personnel.................................... 8
4 Product description........................................................................... 10
4.1 Configuration of the safety controller...................................................... 10
4.2 Overview of the module............................................................................ 10
4.3 Configuration and function...................................................................... 10
4.4 Status indicators....................................................................................... 11
5 Project planning................................................................................ 12
5.1 Manufacturer of the machine.................................................................. 12
5.2 Operating entity of the machine.............................................................. 12
5.3 Design........................................................................................................ 12
5.4 Electrical integration................................................................................. 14
5.4.1 Internal circuitry....................................................................... 14
5.4.2 Fault detection using test outputs.......................................... 14
5.5 Testing plan............................................................................................... 15
6 Mounting............................................................................................. 17
6.1 Safety......................................................................................................... 17
6.2 Mounting procedure................................................................................. 17
6.3 Module exchange...................................................................................... 17
7 Electrical installation........................................................................ 19
7.1 Safety......................................................................................................... 19
7.2 Device connection.................................................................................... 19
7.3 Coding........................................................................................................ 20
7.3.1 Coding front connector and module....................................... 21
8 Commissioning.................................................................................. 23
8.1 Check during commissioning and modifications.................................... 23
CONTENTS
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
3
Subject to change without notice
9 Operation............................................................................................ 24
9.1 Regular thorough check........................................................................... 24
10 Maintenance...................................................................................... 25
10.1 Regular thorough check........................................................................... 25
11 Troubleshooting................................................................................. 26
11.1 Status indicators....................................................................................... 26
11.2 Possible faults........................................................................................... 27
12 Decommissioning............................................................................. 30
12.1 Disposal..................................................................................................... 30
13 Technical data.................................................................................... 31
13.1 Data sheet................................................................................................. 31
13.2 Dimensional drawings.............................................................................. 33
14 Annex.................................................................................................. 35
14.1 Compliance with EU directives................................................................. 35
15 List of figures..................................................................................... 36
16 List of tables....................................................................................... 37
CONTENTS
4
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
1 Ordering information
1.1 Ordering information for main module
Table 1: Ordering information for main module
Part Type Part number
CPUc1 main module
•
20 s
afety capable inputs
•
8 test outputs
•
4 safety outputs
FLX3-CPUC100S14 1119023
1.2 Ordering information for expansion module
Ordering information for IO expansion module
T
able 2: Ordering information for IO expansion module
Part Type Part number
Expansion module XTDI1
•
8 s
afety capable inputs
•
8 test outputs
FLX3-XTDI100S14 1119028
Expansion module XTDO1
•
8 s
afety capable inputs
•
8 safety outputs
FLX3-XTDO100S14 1119027
ORDERING INFORMATION 1
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
5
Subject to change without notice
2 About this document
2.1 Purpose of this document
These operating instructions contain the information required during the life cycle of the
s
afety controller.
Operating instructions of the safety controller must be made available to all people who
work with the device.
2.2 Scope
These operating instructions apply to the Flexi Compact safety controller.
T
his document is included with the following SICK part numbers (this document in all
available language versions):
•
8026642
2.3 Target groups and structure of these operating instructions
These operating instructions are intended for the following target groups: project devel‐
oper
s (planners, developers, designers), installers, electricians, safety experts (such as
CE authorized representatives, compliance officers, people who test and approve the
application), operators, and maintenance personnel.
These operating instructions are organized by the life phases of the device: project
planning, mounting, electrical installation, commissioning, operation and maintenance.
The table below shows the target groups and how – for many applications – these are
typically divided up between the manufacturer and the entity operating the machine in
which the device is to be integrated:
Area of responsibility Target group Specific chapters of these operating instruc‐
t
ions
1)
Manufacturer Project developers
(
planners, developers,
designers)
Project planning, page 12
Technical data, page 31
Installers Mounting, page 17
Electricians Electrical installation, page 19
Safety experts Project planning, pa
ge 12
Commissioning, page 23
Technical data, page 31
Operating entity Operators Troubleshooting, pa
ge 26
Maintenance staff Troubleshooting, page 26
Ordering information, page 5
1)
Chapters not listed here are intended for all target groups. All target groups must follow all of the safety
and warning instructions in all chapters of the operating instructions!
In other applications, the operating organization is also the manufacturer of the equip‐
ment w
ith the corresponding allocation of the target groups.
2.4 Further information
www.sick.com
T
he following information is available via the Internet:
•
This document in other languages
•
Data sheets and application examples
2 A
BOUT THIS DOCUMENT
6
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
•
C
AD files and dimensional drawings
•
Certificates (such as the EU declaration of conformity)
•
Guide for Safe Machinery. Six steps to a safe machine
•
Safety Designer (software for configuring safety solutions made by SICK AG)
2.5 Symbols and document conventions
The following symbols and conventions are used in this document:
Safety notes and other notes
DANGER
Indic
ates a situation presenting imminent danger, which will lead to death or serious
injuries if not prevented.
WARNING
Indic
ates a situation presenting possible danger, which may lead to death or serious
injuries if not prevented.
CAUTION
Indic
ates a situation presenting possible danger, which may lead to moderate or minor
injuries if not prevented.
NOTICE
Indic
ates a situation presenting possible danger, which may lead to property damage if
not prevented.
NOTE
Indic
ates useful tips and recommendations.
Instructions to action
b
The arrow denotes instructions to action.
1. The sequence of instructions for action is numbered.
2. Follow the order in which the numbered instructions are given.
✓
The check mark denotes the result of an instruction.
ABOUT THIS DOCUMENT 2
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
7
Subject to change without notice
3 Safety information
3.1 General safety notes
This chapter contains general safety information about the safety controller.
F
urther safety information is provided in the respective chapters to cover the specific
situations in which the product may be used.
DANGER
If t
he device is not integrated in the way intended by the manufacturer, the protective
function of the device can be impaired. The dangerous state may be ended too late.
b
Plan the integration of the safety component in accordance with the machine
requirements, see "Project planning", page 12.
3.2 Intended use
The Flexi Compact safety controller is a freely configurable control for safety applica‐
t
ions. Sensors and switching elements (e.g. light curtains, laser scanners, switches,
sensors, encoders, emergency stop pushbuttons) are connected to the safety controller
and are linked logically. The corresponding actuators of the machines or systems can
be switched off safely via the switching outputs of the safety controller.
Incorrect use, improper modification or manipulation of the module will invalidate any
warranty from SICK; in addition, any responsibility and liability of SICK AG for damage
and secondary damage caused by this is excluded.
The safety controller system is only suitable for use in industrial environments.
3.3 Improper use
Among others, the safety controller is not suitable for the following applications:
•
Out
doors
•
Underwater
•
In explosion-hazardous areas
•
In residential areas
3.4 Requirements for the qualification of personnel
The protective device must be planned in, installed, connected, commissioned, and
ser
viced by qualified safety personnel only.
Project planning
For project planning, a person is considered competent when he/she has expertise and
experience in the selection and use of protective devices on machines and is familiar
with the relevant technical rules and national work safety regulations.
Mechanical mounting, electrical installation, and commissioning
F
or the task, a person is considered qualified when he/she has the expertise and
experience in the relevant field and is sufficiently familiar with the application of the
protective device on the machine to be able to assess whether it is in an operationally
safe state.
3 S
AFETY INFORMATION
8
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
Operation and maintenance
F
or operation and maintenance, a person is considered competent when he/she has
the expertise and experience in the relevant field and is sufficiently familiar with the
application of the protective device on the machine and has been instructed by the
machine operator in its operation.
SAFETY INFORMATION 3
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
9
Subject to change without notice
4 Product description
4.1 Configuration of the safety controller
Configuration of the safety controller
A s
afety controller comprises the following components:
•
A main module
•
Up to 12 optional expansion modules
4.2 Overview of the module
1
2
3
4
I3
I5
X1
X7
I4
I6
X2
X
8
I7
X3
X5
I8
X4
X6
I2
PWR
I1
5
Figure 1: FLX3-XTDI1 IO expansion module
1
Release element of the module
2
Status indicators (LEDs)
3
Front connector unlocking
4
Front connector with terminals
5
Backplane bus
4.3 Configuration and function
Prerequisites
•
T
he module can only be operated with a main module.
Configuration
T
able 3: Interfaces of the module
Description Quantity
Safety capable inputs 8
Test outputs
1)
8
1)
The test outputs can also be used to switch non-safety elements (e.g., lamps).
Function
T
he module is a safe digital input/output expansion module.
The module offers the following functions:
4 P
RODUCT DESCRIPTION
10
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
•
Monit
oring of the connected safety devices
•
Testing of the connected safety devices and the wiring (short-circuit detection)
•
Use of the test outputs as non-safe outputs
Complementary information
•
Eac
h test output has an independent test pulse generator. This enables differ‐
ent test pulse parameters to be selected and short-circuits in the wiring to be
detected.
•
The element connected to the output during hardware configuration determines
how the test output will be used. If the test output is used for a non-safety element
(e.g., a lamp), then the test pulse is switched off for the output.
•
Voltage is supplied to the module via the backplane bus. Communication with the
main module of the safety controller also occurs via the backplane bus.
4.4 Status indicators
Status indicators
I3
I5
X1
X7
I4
I6
X2
X
8
I7
X3
X5
I8
X4
X6
I2
PWR
I1
XTDI1
1119028
X1
X7
I3
I5
I4
I6
X2
X8
I7
X3
X5 X6
X4
I8
I1
PWR
I2
Figure 2: LEDs for indicating the status
The arrangement of the status indicators corresponds to the arrangement of the termi‐
nals.
Status indicator
T
able 4: Status indicator
Labeling Color Function
PWR Green/Red Device status
I1 … I8 Green Safety capable input 1 … 8
X1 … X8 Green Test output 1 … 8
Further topics
•
"T
roubleshooting", page 26
PRODUCT DESCRIPTION 4
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
11
Subject to change without notice
5 Project planning
5.1 Manufacturer of the machine
DANGER
F
ailure to comply with manufacturer’s obligations
Hazard due to lack of effectiveness of the protective device
b
Carry out a risk assessment before using the safety controller.
b
Do not manipulate, open or modify the components of the safety controller.
b
Make sure the safety controller is only repaired by the manufacturer or by some‐
one authorized by the manufacturer. Improper repair can lead to a loss of the
protective function.
5.2 Operating entity of the machine
DANGER
F
ailure to observe operator obligations
Hazard due to lack of effectiveness of the protective device
b
Changes to the machine and changes to the hardware or the logic programming
of the safety controller necessitate a new risk assessment. The results of this risk
assessment may require the entity operating the machine to meet the obligations
of a manufacturer.
b
Apart from the procedures described in this document, the components of the
safety controller must not be opened or modified.
b
Do not carry out any repair work on components. Improper repair of the safety
controller can lead to a loss of the protective function.
5.3 Design
Mounting
•
En
vironment meets the requirements of IP54 or higher, e.g., IP54 control cabinet.
•
Mounting on a 35 mm × 7.5 mm mounting rail in accordance with IEC 60715.
•
The mounting rail is connected to the functional earth.
•
Mounting rail is mounted on a mounting plate.
•
Mounting plate is connected to functional earth.
•
Mounting in a vertical orientation (on a horizontal mounting rail).
•
Take suitable ESD protection measures.
Air circulation
T
o ensure sufficient air circulation and cooling, sufficient distance must be kept in the
control cabinet above and below the module.
Provide an adequate clearance in front of the module (front side) for the connected
cables.
5 P
ROJECT PLANNING
12
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
≥ 30≥ 30
≥ 25
Figure 3: Clearances for adequate air circulation
R
equired distance:
•
Above and below the module: ≥ 30 mm
•
In front of the module: ≥ 25 mm
PROJECT PLANNING 5
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
13
Subject to change without notice
5.4 Electrical integration
5.4.1 Internal circuitry
Figure 4: Internal circuitry XTDI
5.4.2 Fault detection using test outputs
Important information
WARNING
Unexpected pulses or delayed falling signal edges due to a short circuit
Machine can start up unexpectedly or the dangerous state of the machine may not be
stopped or not stopped in a timely manner.
b
Protect single-channel inputs against short-circuits and cross-circuits.
b
Make sure the signal line is laid with protection (to prevent a cross-circuit with
other signal lines).
b
Take additional safety measures.
Prerequisites
•
Use t
he test outputs of the module to which the device is connected.
•
Use a permissible combination of safety capable inputs (I) and test outputs (X).
I.e. pairings with only an even-numbered or odd-numbered index, e.g. I1 and X1, I9
and X3, I20 and X4 …
5 P
ROJECT PLANNING
14
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
Fault detection by testing
T
he following faults can be detected by testing an element:
•
Faults in electronic sensors with test inputs.
•
Short-circuits between any of the test outputs.
Using a test pulse frequency of ≥ 200 ms and a test pulse duration of 2 ms, you
c
an detect a cross-circuit between the test outputs of 12 sequential modules.
Using a test pulse frequency of ≥ 8 ms and a test pulse duration of 2 ms, you can
detect a cross-circuit between any two sequential test output pairs of a module.
•
S
hort circuits to 24 V DC (to High) on inputs that are connected to test outputs,
regardless of the length of the test gaps and the test periods.
•
Sensor wiring short-circuits to 24 V that could interfere with a switch-off condition.
The following faults cannot be detected:
•
Short circuits between test outputs and the associated input.
Further topics
•
"C
onfiguring elements"
5.5 Testing plan
Testing plan
T
he manufacturer of the machine and the operating entity must define all required
thorough checks. The definition must be based on the application conditions and the
risk assessment and must be documented in a traceable manner.
In addition, the device must be checked for correct functioning after each change to the
configuration.
b
When defining the thorough check, please note the following:
°
Define the type and execution of the thorough check.
°
Define the frequency of the thorough check.
°
Notify the machine operators of the thorough check and instruct them
accordingly.
The following thorough checks are often defined in connection with a protective
device:
•
Thorough check during commissioning and modifications
•
Regular thorough check
Thorough check during commissioning and modifications
T
he following points are helpful when planning the thorough check:
•
Does the thorough check have to be completed by qualified safety personnel?
•
Can the thorough check be completed by personnel specially qualified and author‐
ized to do so?
•
Does the thorough check have to be documented in a traceable manner?
•
Can the thorough check be carried out according to a check list?
•
Do the machine operators know the function of the protective device?
•
Have the machine operators been trained to work on the machine?
•
Have the machine operators been notified about modifications to the machine?
b
Define all guidelines for the thorough check.
PROJECT PLANNING 5
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
15
Subject to change without notice
Regular thorough check
T
he following points are helpful when planning the thorough check:
•
Which thorough check must be carried out and how is it carried out?
•
How often does the thorough check have to be carried out?
•
Do the machine operators have to be notified of the thorough check and do they
need to be instructed accordingly?
b
Define all guidelines for the thorough check.
5 P
ROJECT PLANNING
16
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
6 Mounting
6.1 Safety
WARNING
E
lectrical voltage
There is a risk of injury from electrocution while connecting the devices.
b
Disconnect the power for the entire plant/machine.
WARNING
Unintended start of the plant/machine
The plant/machine could inadvertently start while you are connecting the devices.
b
Disconnect the power for the entire plant/machine.
NOTICE
Enc
losure rating IP20 only applies if the front connector is mounted.
6.2 Mounting procedure
For information on the mounting process, please see the operating instructions:
•
“F
lexi Compact” (SICK part number 8024573)
6.3 Module exchange
Approach
1.
Disconnect module and the connected components from all voltage sources.
2. Take front connector with connected cables off the defective device: Press the
unlocking mechanism of the front connector downwards and pull out the front
connector.
Figure 5: Dismantle front connector
3. Dismantle the defective module.
MOUNTING 6
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
17
Subject to change without notice
4. Mount new module.
5.
Mount front connector with connected cables to the new module: First mount in
the module with bent hook and then engage in the housing.
Click
Figure 6: Mount the front connector
✓
T
he front connector engages with an audible click.
6 MOUN
TING
18
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
7 Electrical installation
7.1 Safety
WARNING
E
lectrical voltage
There is a risk of injury from electrocution while connecting the devices.
b
Disconnect the power for the entire plant/machine.
WARNING
Unintended start of the plant/machine
The plant/machine could inadvertently start while you are connecting the devices.
b
Disconnect the power for the entire plant/machine.
NOTICE
Enc
losure rating IP20 only applies if the front connector is mounted.
7.2 Device connection
Pin assignment
X2
X4
X6
X8
I2
I4
I6
I8
X1
X3
X5
X7
9
1
1
13
15
17
10
12
14
16
18
5
7
3 4
6
8
1 2
I1
I3
I5
I7
Figure 7: Terminals on front connector
T
able 5: Front connector pin assignment
Terminal Pin assignment Description
1 I1 Safety capable input
2 I2
3 I3
4 I4
5 I5
6 I6
7 I7
8 I8
ELECTRICAL INSTALLATION 7
8026644/2021-03-19 | SICK O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1
19
Subject to change without notice
Terminal Pin assignment Description
9 X1 Test output
10 X2
11 X3
12 X4
13 X5
14 X6
15 X7
16 X8
17 NC Not assigned
18 NC Not assigned
Complementary information
13
16
15
Figure 8: Eyelet on front connector
1
Eyelet for cable tie
Connected cables can be fastened to the front connector eyelet using a cable tie. This
re
lieves the strain on the cables.
Further topics
•
"E
lectrical integration", page 14
7.3 Coding
Overview
Y
ou c
an code the front connector and its modules. A uniquely coded front connector
only fits a uniquely coded module. Coding prevents the front connectors from getting
mixed up.
Coding options
•
1-of
-7 codin
g: 7 front connectors can be uniquely coded.
Coding
1 2 3 4 5 6 7
Front connector 1
⃞
C C C C C C
Front connector 2
C
⃞
C C C C C
… …
Front connector 7
C C C C C C
⃞
•
2-of
-7 c
oding: 21 front connectors can be uniquely coded.
Coding
1 2 3 4 5 6 7
Front connector 1
⃞ ⃞
C C C C C
Front connector 2
C
⃞ ⃞
C C C C
… …
7 ELE
CTRICAL INSTALLATION
20
O P E R A T I N G I N S T R U C T I O N S | Flexi IO XTDI1 8026644/2021-03-19 | SICK
Subject to change without notice
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
