#1719
1050 Fountain St N. Cambridge, Ontario, Canada N3H-4R7 Phone: 1-877-650-5775
Cabinet Installation Instructions
For Gas, Electric, Combination and Wood
Stoves
Please Read These Instructions Thoroughly
Before Installing Your Cabinet.
English Edition
Note: If you plan to vent your exhaust hood to the outside, please refer to your range's Owner
Installation and Operating Instructions under Exhaust Hood section before completing this
installation. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg
elbow added to the exhaust line and 2.5' per 45 deg elbow)
Before proceeding, check for damage that may have occurred during shipping. If the
contents are damaged, inform the freight company or your dealer immediately!
Please refer to the "Installation and Operating Instructions" manual to complete your range installation
For 48" Models: 7200, 6200, 6210, 5200, 5210,
30" Models: 9200, 8200, 8210, 4200, 4210
Wood Stove Models: 1903, 1902, 2603, 2602
101507
© 2007 AGA-HEARTLAND
HEARTLAND
1
1. Removing Cabinet from Box........................................................... 2
2. Assembly of Cresting panel............................................................ 3
3. Installing Cabinets for Electric and Combination Stoves ............... 4
4.Installing Cabinets for Gas Stoves ................................................ 5
5. Installing Cabinet for Wood Stoves................................................ 6
6. Venting .......................................................................................... 7
7. Connecting Power to the Cabinet for
Electric and Combination Stoves ....................................................... 8
8.Connecting Power to the Cabinet for Gas Stoves .......................... 9
TABLE OF CONTENTS
2
Fig. 1
TWO PEOPLE ARE REQUIRED TO DO THE INSTALLATION
Cardboard
corners
Lift here
Cardboard
Cross brace
- Remove the 4 cardboard corners.
- Remove small box and its contents.
- Remove the cardboard cross brace.
- Remove the plastic wrapped cresting panel.
The cabinet comes assembled , except cresting panel (see next page for assembly
instructions) and only requires attachment (installation) to the base of the stove. Further
assembly of optional venting of the exhaust fan may be required.
Before removing the cabinet assembly from the box, make sure you :
Please read through these instuctions before installing the cabinet on the stove base.
Small boxcontains:
- hardware package
- deflector ( not included with woodstove
cabinets.)
- 3 1/2"x10 exhaust adapter ( not included with
woodstove cabinets.)
Cresting panel
packed in plastic
bubble wrap
3
Assembly of Cresting Panel.
Main Cabinet
Cresting Panel
(NOTE: if your cupboards are too low the cresting panel may be left off).
Wingnut
Locate cresting panel packed in bubble wrap.
Unwrap the cresting panel and remove the wingnuts.
Place the cresting panel on the rear of the top of the cabinet.
Take the wingnuts and fasten the cresting panel to the cabinet through the holes at each
end of the cabinet. For:
WOOD STOVES - go through the cabinet door.
GAS, ELECTRIC & COMBINATION STANDARD OR SELF CLEAN STOVES - go through
the filter openings.
view of top of cabinet
4
ELECTRIC AND COMBINATION STOVES ONLY
STOVE
TOP
Gasket - Peel off backing
and stick on.
Bracket
Sheet metaI
screw (black)
Steel Washer Machine screw
(Nickel Plated)
-Remember when working with the cabinet, the cabinet is top heavy. Use your hand to support it during
installation.
-Place box on the floor close to stove. (See Fig. 1 Page 2).
-With a helper,lift cabinet assembly from box by area that is circled.(See Fig.1 Page 2).
-Rest the cabinet assembly on the carton,while your helper steadies the cabinet,peel the cabinet backing off the
gasket and stick one on each bracket.
-Place cabinet assembly onto stove body.(See diagram above)
Caution: In the case of the Glass cooktop models 8200, 8210, 6200, 6210:
DO NOT REST CLOSET CORNER BRACKETS ON GLASS, to prevent damage to glass top
-Line up holes in the bottom (foot) of the bracket with the holes in the stove top,while one person supports the
cabinet, fasten the cabinet brackets to the stove top with machine screws .
-To fasten the splashback to the rear of stove, with the Models 5200, 5210, 6200, 6210 use 5 sheet metal
screws and washers. For Models 4200, 4210, 8200, 8210 use 4 sheet metal screws and washers. To prevent
chipping do not overtighten or use power tools.
Gasket
Machine screw
Steel washer
Sheet metal
screw
5
GAS STOVES ONLY
STOVE
TOP
Gasket - Peel off backing
and stick on.
Bracket
(WOOD STOVES SEE NEXT PAGE)
Sheet metaI
screw (black)
Steel Washer Nut Machine screw
(Nickel Plated)
-Remember when working with the cabinet, the cabinet is top heavy. Use your hand to support it during
installation.
-Place box on the floor close to stove. (See Fig. 1 Page 2).
-With a helper,lift cabinet assembly from box by area that is circled.(See Fig.1 Page 2).
-Rest the cabinet assembly on the carton,while your helper steadies the cabinet,peel the cabinet backing off the
gasket and stick one on each bracket.
-Place cabinet assembly onto stove body.(See diagram above)
-Line up holes in the bottom (foot) of the bracket with the holes in the stove top,while one person supports the
cabinet, fasten the cabinet brackets to the stove top with machine screws and nuts.
-To fasten the splashback to the rear of stove, with the Model 7200 use 5 sheet metal screws and washers.
For Model 9200 use 4 sheet metal screws and washers. To prevent chipping do not overtighten or use
power tools.
Gasket
Nut
Machine screw
Steel washer
Sheet metal
screw
48" models only-right
brackel front screw
attachment:machine
screw attached to stove
top without use of nut.
6
STOVE
TOP
Bracket
-Remove the nuts, washers and screws located at rear edge of stove top (2 on SWEETHEART,4 on
OVAL) and the 4 machine screws from the stove top.
-With a helper, lift cabinet assembly from box by area that is circled. (See Fig. 1 Page 2).
-Place cabinet assembly onto stove body. (See diagram above).
-Line up holes in the bottom (foot) of the bracket with the stove top holes while one person supports
cabinet, fasten the cabinet brackets to the stove with machine screws (2 each side). (See diagram
above).
-Place box on the floor close to stove. (See Fig. 1 Page 2).
WOOD STOVES ONLY
-Re-insert screws from the inside of the lip at the back of stove through the splashback , then
assemble the nuts and washers to each screw (2 on a SWEETHEART 4 on OVAL). Tighten nuts to
a snug fit. To prevent chipping do not overtighten or use power tools.
Screwdriver
Machine screw
Remove machine screws
from the top (2 each side)
7
Sheet metal
screw
3 1/2" x 10" Exhaust adaptor
If you are not venting outside, attach the deflector to the rear of cabinet with 4, sheet metal
screws. If you are venting outside, attach the 3 1/2" x 10" exhaust adaptor with 4, sheet metal
screws. Fasten your exhaust ducting to the adaptor.
Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to
the exhaust line and 2.5' per 45 deg elbow)
GAS, ELECTRIC AND COMBINATION STOVES ONLY
Deflector
Back of cabinet
8
CONNECTING POWER TO THE CABINET
COMBINATION AND ELECTRIC SELF CLEAN OR STANDARD STOVES ONLY
(SEE NEXT PAGE FOR GAS STOVES)
After your exhaust hood has been installed the very last thing to do is to connect the multipin
plug to the range. The receptacle is located at the rear of the stove by the main power cord.
When installing the multi-pin plugs,
make sure the flat sided pins are
aligned with flat sided holes. Each plug
is coded for proper fit. Do not force
plug into receptacle.
Insert themulti-pin plugs into correspond-
ing receptacles- each plug is coded to
match its receptacle.
Loop power cord on back and attach
power cord to stove back with supplied
cable tie and screw
Plug the stove into wall receptacle.
Check all electrical functions of the
cabinet (fan,light, clock, etc.) and check
againthat ALL screws have been tight-
ened before completeing the installa-
tion.
Exhaust Hood Recptacle Locations
5200, 5210,
6200, 6210,
4200, 4210,
8200, 8210,Back of
stove
Back of
stove
9
Models 7200, 9200 only
Exhaust Hood Receptacle Locations
male end of the
cabinet power cord
Power In
(male receptacle)
Exhaust Hood In
(female receptacle,
from cabinet
)
Power In
(male receptacle)
Exhaust Hood In
(female receptacle,
from cabinet)
Model 9200
Model 7200
After your exhaust hood has been installed, connect the plug to the range.The female recep-
tacle for the exhaust hood is located at the rear of the stove by the main power (male) recepta-
cle. Simply plug the male end of the cabinet power cord into the female receptacle.
Plug the stove into wall receptacle.
Check all electrical functions of the cabinet (fan,light,clock,etc.) and check again that ALL
screws have been tightened before completing the installation.
GAS STOVES ONLY
female receptacle
Back of stove
Back of stove
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Heartland Bakeware 9200/7200 User manual
-
Heartland 9200 Owner's manual
-
-
-
-
-
-
-
-
Other documents
-
GBC 3747530 Datasheet
-
Heartland Cabinetry 8000405P Operating instructions
-
Prescientx Aranet4 Wall Mount Operating instructions
-
Heartland Appliances Oval 1902 Installation And Operating Instructions Manual
-
Heartland Bakeware 3805-3825 User manual
-
AGA Ventilation Hood Instruction & Installation Manual
-
Meyer Sound UP-4slim Operating instructions
-
Enviro C-10135 User manual
-
-
Intermec PEN*KEY 6200 Troubleshooting Manual
