PYLE Audio PSS4 User manual

HIGHPOWERSTEREOSPEAKERSELECTOR

MODEL:PSS4/PSS6

www.pyleaudio.com

ThankyouforpurchasingPYLEPROMulti-SpeakerSelectors.Itletsyouconnectup

tofour(PSS4)orsix(PSS6)separatepairsofspeakerstoyourstereoreceiver/amplifier.

Thecontrolcenterisespeciallyconvenientifyouhavespeakersetsindifferentrooms

andwanttoturnthemonandoffindependently.Youcanenjoytheconvenienceand

flexibilityoflisteningtomultiplespeakerpairssimultaneously.

Thecontrolcenterletsyouuseonetofour(PSS4)orsix(PSS6)setsofspeakersata

time,andisdesignedtooperatewithastereoreceiver/amplifierthathasamaximumof

100wattsperchannel,andwithspeakersystemsthathaveaminimumimpedanceof8

ohms(see“ImpedanceChart”onpage5)

PREPARATIONS

•UsethePYLEPROSpeakerSelectorsonlywithamplifiersratedat100wattsper

channelorless.

•YourPYLEPROSpeakerSelectorisdesignedtoacceptanysizecableupto14gauge

non-terminatedspeakerwire.Ifyou’reusingnon-terminatedspeakerwire,donotuse

anyspeakerwirethatislargerthan14gauge.Thelowerthegaugenumber,thelarger

thecable(e.g.,12gaugeislargerinactualphysicalsizethan14gauge).

•Donothooktheoutputsofoneselectorintotheinputsofanotherspeakerselector

together.

MAKINGTHECONNECTIONS

Thecontrolcenterdividesthepowerfromyourreceiver/amplifierdifferentlytoits

speakerterminals.(Thisisespeciallynoticeablewhenyouconnectonlyonepairof

speakers.Ifyouconnectmorethanonepairofspeakers,see“ImpedanceChart”on

page5toselectorthebestterminalstoconnect.)Forthebestperformance,makethe

connectionsbasedonhowfrequentlyyouuseeachsetofspeakers.

Cautions:Toavoiddamagingyourspeakersorreceiver/amplifier:

•Besureyourreceiver/amplifier’spoweristurnedoffbeforeyoumaketheconnections.

•Neverletthespeakerwire’sbareendstoucheachotherortheadjacentterminalsonthe

controlcenter.

•Donotconnectmorethanonepairofsepakerstoeachsetofterminals.

PressopenthedesiredSPKterminalsonthecontrolcenter.Insertthespeakers’positive

(+)wiresinthepositive(red)terminals,andnegative(

)wiresintothenagative(black)

terminals,accordingtotherespectiveL(left)andR(right)terminals.Thenpressthetabs

toclosethem.

PressopentheAMPterminalsonthecontrolcenter,theninsertyourreceiver/amplifier’s

positive(+)wiresintothepositive(red)terminals,andnegative(

)wiresinthenagative

terminals.Thenpressthetabstoclosethem.

Notes:

•Ifyourreceiver/amplifierhasmorethanonesetofspeakerterminal(AandB),connect

onlyoneortheothertothecontrolcenter.

•Forthebestresults,werecommend14-gauge,twoconductorspeakerwire(not

supplied)formostconnections.Ifyouplantolocatedthespeakersfurtherthan80feet

fromthecontrolcenter,useaheaviergaugeofwire.

OPERATION

Caution:Toavoiddamagingyourreceiver/amplifier,setitsvolumetothelowestsetting

beforechangingthecontrolcenter’ssettings.

Toturnonapairofspeakersconnectedtothecontrolcenter,simplypressinthedesired

button.Forexample,toturnonthesetofspeakersconnectedtoSPKA,pressA.

Toturnoffapairofspeakers,pressthebuttonagainsoitisinthe“out”position.

Note:ifnospeakersareconnectedtoasetofterminals,donotpressinthecorresponding

controlbutton.

IMPEDANCECHART

Impedanceisameasurementoftheloadplacedonyourreceiver/amplifierbythe

speakers.Theloadplacedonyourreceiver/amplifierfromthtecontrolcenterwill

varydependingonhowmanypairsofspeakersyouturnonatonetime,andonwhich

speakersyouturnon.Thechartbelowshowstheimpedanceforallpossiblecombinations

of8-ohmspeakers.

PSS6

Speaker Sets On Impedance (Ω)

A, B, C, D, E or F 8

A+B, A+C, A+D

A+E, A+F, B+C

B+D, B+E, B+F

C+D, C+E, C+F, E+F

A+B+C, A+B+D, A+B+E

A+B+F, A+C+D, A+C+E

A+C+F, A+D+E, A+D+F

A+E+F, B+C+D, B+C+E

B+C+F, B+D+E, B+D+F

C+D+E, C+D+F, D+E+F

3.1

A+B+C+D, A+B+C+E

A+B+C+F, A+C+D+E

A+C+D+F, A+D+E+F

B+C+D+E, B+C+D+F

C+D+E+F

2.4

A+B+C+D+E+F 1.7

PSS4

Speaker Sets On Impedance (Ω)

A, B, C or D 8

A+B, A+C, A+D

B+C, B+D, C+D

A+B+C, A+B+D

A+C+D, B+C+D

3.1

A+B+C+D 2.4

SPECIFICATIONS

AudioPowerHandling 50W(R.M.S.)/ch,

100W(Max)/ch

FrequencyResponse 20Hzto20KHz

ChannelSeparation 80dB

Crosstalkbetweenchannels 50dB

Speakerterminalwiresizerequirements14-22awg

Dimensions(WxHxD) 190x50x120mm(PSS4)

 250x50x150mm(PSS6)

Weight 0.81kgs(1.79lbs)(PSS4)

1.15kgs(2.54lbs)(PSS6)

PYLE Audio PSS4, PSS6 User manual

Related papers

Other documents