Biostar TA890FXE - BIOS User manual

TA890FXE Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................. 14

3.1 How to Setup Jumpers .................................................................... 14

3.2 Detail Settings.................................................................................. 14

Chapter 4: Hybrid CrossFireX Function ................ 20

4.1 Hybrid CrossFireX Requirements .................................................. 20

4.2 Hybrid CrossFireX Installation....................................................... 20

Chapter 5: RAID Functions .................................. 21

5.1 Operating System............................................................................ 21

5.2 Raid Arrays ...................................................................................... 21

5.3 How RAID Works............................................................................. 21

Chapter 6: T-Series BIOS & Software................... 25

6.1 T-Series BIOS..................................................................................... 25

6.2 T-Series Software ............................................................................. 33

Chapter 7: Useful Help ........................................ 43

7.1 Driver Installation Note.................................................................. 43

7.2 Extra Information............................................................................ 44

7.3 AMI BIOS Beep Code....................................................................... 45

7.4 AMI BIOS Post Code ........................................................................ 46

7.5 Conversion Of Hexadecimal and Decimal System...................... 48

7.6 Troubleshooting............................................................................... 49

Appendix: SPEC In Other Languages ................... 50

German.................................................................................................................. 50

French .................................................................................................................... 52

Italian..................................................................................................................... 54

Spanish ................................................................................................................... 56

Portuguese ............................................................................................................ 58

Polish...................................................................................................................... 60

Russian ................................................................................................................... 62

Arabic..................................................................................................................... 64

Japanese ................................................................................................................ 66

TA890FXE

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

IDE Cable X1 (optional)

Serial ATA Cable X3

Serial ATA Power Cable X1

Rear I/O Panel for ATX Case X1

User’s Manual X1

Fully Setup Driver CD X1

FDD Cable X1 (optional)

USB 2.0 Cable X1 (optional)

S/PDIF out Cable X1 (optional)

CFX Bridge X2

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

Socket AM3

AMD Sempron / Phenom II / Athlon II

processors

AMD 64 Architecture enables 32 and 64 bit

comput ing

Supports Hyper Transport 3.0

FSB

Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

Chipset

AMD 890FX

AMD SB850

Super I/O

ITE 8721

Provides the most commonly used legacy

Super I/O functionality.

Low Pin Count Interface

Environment Control init iatives,

H/W Monitor

Fan Speed Contro ller

ITE's "S mart Guardian" funct ion

Main

Memory

DDR3 DIMM Slots x 4

Max Memory Capacity 16GB

Each DIMM supports 512MB/

1GB/2GB/4GB DDR3

Dual Channel Mode DDR3 memory module

Supports DDR3 800 / 1066 / 1333

Supports DDR3 1600 (OC)

IDE

VIA VT6330

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

SATA III

Integrated Serial ATA Controller

Data transfer rates up to 6 Gb/s.

SATA Vers ion 3.0 specificat ion co mp liant.

RAID 0,1,5,10 support

LAN

Realtek RTL 8111DL

10 / 100 Mb/s / 1Gb/s auto negotiation

Half / Full duplex capability

Sound

ALC892

7.1channels audio out

Supports HD Audio

IEEE 1394

VIA VT6330 1394a

PCI Slot x2 Supports PCI expansion cards

Slots

PCI Express Gen2 x16 Slot x4

Supports PCI-E Gen2 x16,x16, x4, x1 expansion

cards

IDE Connector x1 Each connector supports 2 IDE devices

SATA Connector x5 Each connector supports 1 SATA device

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

S/PDIF out Connector x1 Supports digital audio out function

On Board

Connectors

Consumer IR Connector x1 Supports infrared function

TA890FXE

3

SPEC

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x2 System Fan Power supply

CMOS clear Header x1 Restore CMOS data to factory default

USB Connector x3 Each connector supports 2 front panel USB ports

IEEE 1394 Connector x1 Connects to IEEE 1394 device

Serial Port Connector x1 Connects to RS-232 Port

Power Connector (24-Pin) x1 Connects to Power supply

Power Connector (8-Pin) x1 Connects to Power supply

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

Optical +coaxial S/PDIF Out x1

1394 Port x1

eSATA Port x1

LAN port x1

USB Port x6

Audio Jack x6

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Provides digital audio out function

Connects to IEEE 1394 device

Connect to SATA devices

Connect to RJ-45 ethernet cable

Connect to USB devices

Provide Audio-In/Out and Mic. connection

Board Size

305 mm (W) x 244 mm (L) ATX

OS Support

Windows XP / Vista / 7

Biostar reserves the right to add or remove support

for any OS With or without notice.

1.4 REAR PANEL CONNECTORS

PS/2

Mouse

PS/2

Keyboard

Line In

Line Out

Mic In

Center

Rear

Side

eSATA

USBX2

LAN

USBX2

IEEE 1394

USBX2

Optical +coaxial

S/PDIF Out

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

KBMS1

SPDIF1

US B_13 94_

ESATA1

R J45U SB 1

AUDIO1

USB1

JUSBV1

C odec

LAN

ATXPW R2

AU X PW R1

PEX16_1

PEX16_2

PEX16_3

PEX16_4

PCI2

PCI1

F_AUDIO1

JSPDIFOU T1

CIR1

F_1 394A 1

J_C OM1

F_USB3

SYS_FAN1

F_USB1

F_USB2

SW_PWR1

SW_RST1

PANE L1

JUSBV2

IDE1

JCMOS1

BAT1

BIOS

SATA2

SATA1

SATA3

ATXPWR1

DDR3_A1

DB1DR3_

DB2DR3_

DA2DR3_

AMD

SB850

AMD

890FX

CPU_FAN1

Super

I/O

NB_PH1 _D1

NB_PH1 _D2

PH1_ D1

PH2_ D2

PH3_ D3

PH4_ D4

Socket AM3

SYS_FAN2

Note: represents the 1■

st

pin.

TA890FXE

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only

in the correct orientation.

Motherboard Manual

6

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the

installation.

TA890FXE

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

CPU_FAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

1

4

4 Smart Fan

Control (By Fan)

SYS_FAN1: System Fan Header

SYS_FAN2: NorthBridge Fan Header

Pin Assignment

1 Ground

2 +12V

SYS_FAN2

SYS_FAN1

13

3

FAN RPM

rate sense

Note:

CPU_FAN1, SYS_FAN1/2 support 4-pin and 3-pin head connectors. When connecting

with wires onto connectors, please note that the red wire is the positive and should be

connected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. DDR3 Modules

DDR 3_A1

DB1DR 3_

DA2DR 3_

DB2DR 3_

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

TA890FXE

9

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Mem ory

Size

DDR3_A1 512MB/1GB/2GB/4GB

DDR3_B1 512MB/1GB/2GB/4GB

DDR3_A2 512MB/1GB/2GB/4GB

DDR3_B2 512MB/1GB/2GB/4GB

Max is 16GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

DDR3_A1

DDR3_B1 DDR3_A2 DDR3_B2

Enabled O O X X

Enabled X X O O

Enabled O O O O

(O: memory installed; X: memory not installed)

The DRAM bus width of the memory module must be the same (x8 or

x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

IDE1: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode

0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

40

2

39 1

SATA1~SATA3: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 5 channels SATA interface,

it satisfies the SATA 3.0 spec and with transfer rate of 6.0Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

147

SATA3

SATA1- SATA2-

1- 2-

UU

SATA L SATA L

7 Ground

TA890FXE

11

ATXPWR1: AT X Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

ATXPWR2: AT X Power Source Connector

This connector provides +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 +12V

4 +12V

5 Ground

6 Ground

7 Ground

1

45

8

8 Ground

Note:

Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2

connectors have been plugged-in.

If CPU power plug is 4-pin, please plug it into Pin 1-2-5-6 of ATXPWR2.

Motherboard Manual

12

AUXPWR1: Auxiliary Power for Graphics

This connector is an auxiliary power connection for graphics cards. Exclusive

power for the graphics card provides better graphics performance.

Assignment

1 +12V

2 Ground

3 Ground

4 VCC

41

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI2

PCI1

TA890FXE

13

PEX16_1/PEX16_3: PCI-Express Gen2 x16 Slots

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- PEX16_1 & PEX16_3 slots are reserved for graphic or video cards.

PEX16_4: PCI-Express Gen2 x4 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 2GB/s simultaneously per

direction, for an aggregate of 4GB/s totally.

PEX16_2: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

PEX16_1

PEX16_4

PEX16_2

PEX16_3

Motherboard Manual

14

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

P

W

R

_

L

E

D

R

S

T

H

L

E

D

S

P

K

+

-

1

916

8

O

n

/

O

f

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

TA890FXE

15

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and

the CMOS data. Please carefully follow the procedures to avoid damaging the

motherboard.

1

3

Pin 1-2 Close:

Normal Operation

(default).

1

3

1

3

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

J_COM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

19

210

10 NC

Motherboard Manual

16

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

1

2

9

10

JSPDIFOUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

1

3

3 Ground

CIR1: Consumer IR Connector

This header is for infrared remote control and communication.

Pin Assignment

1 IrDA serial input

2 Ground

3 Ground

4 Key

5 IrDA serial output

6 IR Power

1

2

5

6

TA890FXE

17

F_1394A1: IEEE 1394 Header

This header allows user to connect IEEE 1394 device.

Assignment

1 TPA1+

2 TPA1-

3 GND

4 GND

5 TPB1+

6 TPB1-

7 VCC

8 VCC

9 N/A

1

2

9

10

10 KEY

BIOS POST Code/CPU Temperature Indicator

This indicator will show POST code while booting. After the booting sequence,

it will show current CPU temperature through hexadecimal figure. Please

refer to Chapter 7.4 for all the BIOS POST codes, and Chapter 7.5 for

conversion of hexadecimal and decimal system.

Motherboard Manual

18

F_USB1~F_USB3: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

12

910

F_USB1 F_USB3

F_USB2

10 NC

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/USB_1394_ESATA1/RJ45USB1.

JUSBV2: +5V for USB ports at F_USB1/F_USB2/F_USB3.

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/USB_1394_ESATA1/

RJ45USB1.

JUSBV2: +5V STB for USB ports at F_USB1/F_USB2/F_USB3.

13

Pin 1-2 close

13

3

1

JUSBV1

JUSBV2

13

Pin 2-3 close

Page is loading ...

Biostar TA890FXE - BIOS User manual

This manual is also suitable for

Biostar TA890FXE - BIOS User manual

Related papers

Other documents