Datalogic Gryphon M200 User manual

Category
Bar code readers
Type
User manual

Datalogic Gryphon M200 is a cordless reader that offers fast and reliable barcode scanning. It features a long-lasting battery, a durable design, and a variety of configuration options. With its ability to read 1D and 2D barcodes, the Gryphon M200 is ideal for use in retail, healthcare, and other industries.

Datalogic Gryphon M200 is a cordless reader that offers fast and reliable barcode scanning. It features a long-lasting battery, a durable design, and a variety of configuration options. With its ability to read 1D and 2D barcodes, the Gryphon M200 is ideal for use in retail, healthcare, and other industries.

Gryphon™ Mx00
Quick Reference
Gryphon™ Mx00 Readers
QUICK REFERENCE
DATALOGIC S.p.A.
Via Candini 2
40012 - Lippo di Calderara di Reno
Bologna - Italy
Gryphon™ Mx00 Readers
Ed.: 10/2009
ALL RIGHTS RESERVED
Datalogic reserves the right to make modifications and improvements without prior
notification.
Datalogic shall not be liable for technical or editorial errors or omissions contained herein,
nor for incidental or consequential damages resulting from the use of this material.
Product names mentioned herein are for identification purposes only and may be
trademarks and or registered trademarks of their respective companies.
© Datalogic S.p.A. 2001-2009
820000744 (Rev. F)
CONTENTS
Updates and Language Availability.....................................................................iv
Using Gryphon™ M Series Readers................................................................... 1
Charging the Batteries ........................................................................................ 2
Gryphon™ M Configuration ................................................................................ 3
Using Multiple Readers with Same Cradle.......................................................... 5
Gryphon™ M Default Configuration .................................................................... 5
Technical Features.............................................................................................. 7
Warranty.............................................................................................................. 8
Services And Support ......................................................................................... 8
Patents ................................................................................................................ 8
Compliance ......................................................................................................... 8
Reading Diagrams ............................................................................................ 10
Numeric Table................................................................................................... 11
iii
UPDATES AND LANGUAGE AVAILABILITY
UK/US
The latest drivers and documentation updates for this product are available on
Internet.
Log on to : www.datalogic.com
I
Su Internet sono disponibili le versioni aggiornate di driver e documentazione di
questo prodotto. Questo manuale è disponibile anche nella versione italiana.
Collegarsi a : www.datalogic.com
F
Les versions mises à jour de drivers et documentation de ce produit sont
disponibles sur Internet. Ce manuel est aussi disponible en version française.
Cliquez sur : www.datalogic.com
D
Im Internet finden Sie die aktuellsten Versionen der Treiber und Dokumentation
von diesem Produkt. Die deutschsprachige Version dieses Handbuches ist
auch verfügbar.
Adresse : www.datalogic.com
E
En Internet están disponibles las versiones actualizadas de los drivers y
documentación de este producto. También está disponible la versión en
español de este manual.
Dirección Internet : www.datalogic.com
iv
GRYPHON™ MX00
USING GRYPHON™ M SERIES READERS
The Gryphon™ M series reader, paired with an OM-Gryphon™ cradle, builds a
Cordless Reading System for the collection, decoding and transmission of
barcoded data.
Gryphon™ M readers automatically scan barcodes at a distance. Simply aim
and pull the trigger. Code scanning is performed along the center of the light bar
emitted from the reading window. This bar must cover the entire code.
READING ANGLE
Successful scanning is obtained by tilting the reader with respect to the barcode
to avoid direct reflections which impair the reading performance, see the figure
below.
Successful reading is obtained by an audible tone plus a good-read green spot.
OK Not Advised
Good read spot
Good read LED
To start using your Gryphon™ M reading system you must:
1. Connect an OM-Gryphon™ cradle to the Host. For installation and
connection information see the OM-Gryphon™ Quick Reference Manual.
2. Charge the Gryphon™ M battery using an OM-Gryphon™ / C-Gryphon™
charger as described in this Quick Reference manual. A full charge takes
3
hours with NiMh battery models.
3. Configure the reader as described in this Quick Reference manual.
4. Co
nfigure the OM-Gryphon™ cradle. See OM-Gryphon™ Configuration in
the “OM-Gryphon™ Quick Reference”.
1
DATALOGIC
CHARGING THE BATTERIES
By placing the reader onto the OM-Gryphon™ cradle or C-Gryphon™ battery
charger it is possible to charge the Gryphon™ M batteries. Make sure the
charging LED goes on.
The LEDs positioned on the cradle signal the charge status, as described in the
following table:
LED STATUS
Power on /
Data
Yellow On = OM-Gryphon™ is powered.
Yellow Blinking = OM-Gryphon™ receives data and
commands from the Host or the reader.
Charging
Red On = the battery charge is in progress.
Red Blinking = the battery reconditioning is in progress.
Charge
completed
Green On = the battery is completely charged.
Charging +
Charge
completed
Red and Green Blinking together = the reader is not
correctly placed onto the reader.
D
I
S
C
H
A
R
G
E
Power on / Data
(yellow LED)
Reconditioning battery
button
Charging
(red LED)
Charge completed
(green LED)
After many
recharging cycles NiMh and NiCd batteries may tend to lose their
operating autonomy. This condition can be overcome by positioning the
Gryphon™ M onto the OM-Gryphon™ / C- Gryphon™ charger and pressing the
“battery reconditioning” button.
2
GRYPHON™ MX00
When the above procedure is no longer effective, the batteries must be
changed. To change the batteries of your reader, unscrew the battery cover
screw, replace the old batteries with new ones, then insert the cover in the
handle and screw it back into place. (See the following figures).
+
WARNING
Do not incinerate, disassemble, short terminals or
expose to high temperature. Risk of fire, explosion. Use
specified charger only. Risk of explosion if the battery
is replaced by an incorrect type. Dispose of the
batteries as required by the relevant laws in force.
GRYPHON™ M CONFIGURATION
When the OM-Gryphon™ cradle is connected and powered, configure the
Gryphon™ M by reading the following codes in the given sequence and follow the
instructions.
Note: for the numeric code selection of step 3, use the table at the end of this
Quick Reference.
Restore Gryphon™ M default
1.
Ì$+$*oÎ
Enter configuration
2.
Ì$+;Î
Set Radio Address
3.
ÌRF8Î
+
four digits for the Gryphon™ M Address
(from 0000 to 1999).
All readers used in the same area must have different addresses.
3
DATALOGIC
Exit and Save configuration
4.
Ì$-?Î
5.
Read the Bind code to pair the Gryphon™ M to the OM-Gryphon™
cradle.
The reader is dedicated to the cradle. Any previously bound reader will
be excluded.
To connect several readers to the same cradle see the following section
"Using Multiple Readers with Same Cradle".
Bind
Ì$+RN0$-IÎ
The green LED on the Gryphon™ M will blink: the reader is ready to be
positioned onto the cradle.
6.
Firmly position the reader onto the cradle within 10 seconds, a beep will
be emitted, signaling that the OM-Gryphon™ cradle has been paired to
the Gryphon™ M, and the green LED on the reader will go off.
Green LED
YOUR READER IS NOW CONFIGURED TO READ CODES USING THE
DEFAULT VALUES.
7.
Configure the OM-Gryphon™ cradle, refer to the “OM-Gryphon™ Quick
Reference”.
4
GRYPHON™ MX00
USING MULTIPLE READERS WITH SAME
CRADLE
If you want to use several readers associated with the same cradle, you must
first Bind the cradle with one of the readers (see previously described
configuration procedure).
Successive readers
can be associated with the same cradle by following the
configuration procedure substituting the Bind command with Join.
5.
Join
Ì$+RN1$-NÎ
The green LED on the Gryphon™ M will blink: the reader is ready to be
positioned onto the cradle. Complete step 6.
CAUTION
If the cradle is not
Bound to a reader, its address assumes
a random value which can cause conflicts and malfunctions
to other cradles within its range.
GRYPHON™ M DEFAULT CONFIGURATION
DATA FORMAT
code identifier disabled (enabled for POS terminals), field adjustment
disabled, code length tx not transmitted, character replacement disabled
POWER SAVE
scan rate 270 scans/s
READING PARAMETERS
operating mode hand-held, hardware trigger, trigger active level, no timeout,
Flash On = 1 sec, Flash Off = 0.6 sec, one read per cycle, safety time 0.5
sec, beeper intensity high, tone 2, beeper type monotone, beeper length
short, good read spot duration medium
DECODING PARAMETERS
ink spread enabled, overflow control enabled, interdigit control enabled,
Puzzle Solver™ disabled, decoding safety = one read
5
DATALOGIC
CODE SELECTION
Enabled codes
Code PDF417 (only Gryphon™ M200)
EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
Interleaved 2/5
check digit control and transmission, variable length code; 4-99
characters
Standard Code 39
no check digit control, variable length code; 1-99 characters
Code 128
variable length code; 1-99 characters
Disabled codes for M100 only:
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI,
Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49,
RSS Codes
Disabled codes for M200 only:
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes,
RSS Codes
ADVANCED FORMATTING PARAMETERS
concatenation disabled, no advanced formats defined
RADIO PARAMETERS
radio protocol timeout = 2 seconds, power-off timeout = 4 hours, single store
disabled, beeper control for radio response = normal.
6
GRYPHON™ MX00
TECHNICAL FEATURES
Gryphon™ Mx00
Electrical Features
Battery Type 2 AA NiMh* batteries
1.2 V – 1400 mAh
Time of recharge NiMh 3 hours
Operating autonomy
(typ. continuous reading)
25,000 reads - NiMh
Indicators LED, Good Read Spot, Beeper
Max scan rate 270 scans/sec
Optical Features
Sensor CCD solid state (3648 pixels)
Illuminator LED array
Wavelength 630 ~ 670 nm
Max. LED Output Power 0.33 mW
Reading field see reading diagram
Max. resolution 0.076 mm, 3 mils
PCS minimum 15% (Datalogic Test Chart)
Radio Features
European Models USA Models
Working frequency 433.92 MHz 910 MHz
Bit rate 19200 baud 36800 baud
Effective Radiated Power <10 mW < 1mW
Range (in open air) 30 m 15 m
RF Modulation FSK
System Configuration OM-GRYPHON™ STARGATE
Maximum number of devices per
base stations
16 255
Max. number of devices in the
same reading area
2000
Environmental Features
Working Temperature 32° to 104 °F
Storage Temperature
(without battery)
- 4° to 158 °F
Humidity 90% non condensing
Drop resistance IEC 68-2-32 Test ED
Protection class IP30
Mechanical Features
Weight (with batteries) about 9.87 oz
Dimensions 7.04 x 3.18 x 3.85 in
Material ABS and Polycarbonate molded with
rubber
* It is possible to employ also NiCd or non-chargeable Alkaline AA batteries.
7
DATALOGIC
WARRANTY
Datalogic warranties this product against defects in workmanship and materials,
for a period of 24 months from the date of shipment, provided that the product is
operated under normal and proper conditions.
Datalogic has the faculty to repair or replace the product, these provisions do
not prolong the original warranty term. The warranty does not apply to any
product that has been subject to misuse, accidental damage, unauthorized
repair or tampering.
SERVICES AND SUPPORT
Datalogic provides several services as well as technical support through its
website. Log on to www.datalogic.com and click on the links
indicated for
further information including:
PRODUCTS
Search through the links to arrive at your product page where you can
download specific Manuals
and Software & Utilities including:
- DL Sm@rtSet™ a Windows-based utility program which allows device
configuration using a PC. It provides RS232 interface configuration as
well as configuration barcode printing.
SERVICES & SUPPORT
- Datalogic Services
- Warranty Extensions and Maintenance
Agreements
- Authorised Repair Centres
CONTACT US
E-mail form and listing of Datalogic Subsidiaries
PATENTS
This product is licensed under the following U.S. patent:
6,158,661
This product is covered by one or more of the following patents:
U.S. patents 5,992,740; 6,305,606 B1; 6,517,003 B2; 6,631,846 B2; 6,712,271
B2; 6,808,114 B1; 6,817,525 B2, and 6,834,806 B2
European patents 851,378 B1; 895,175 B1; 962,880 B1; 997,760 B1;
1,128,315 B1; and 1,164,536 B1
Additional patents pending.
COMPLIANCE
This device must be opened by qualified personnel only.
The batteries must be removed before opening the device.
8
GRYPHON™ MX00
RADIO COMPLIANCE
Contact the competent authority responsible for the management of radio
frequency devices of your country to verify the eventual necessity of a user
license.
Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for
further information.
LED CLASS
EN60825-1:(2001)
Gryphon™ Mx00 USA
Gryphon™ Mx00 EU
Class 1 LED product.
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed written
approval of Datalogic could void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference which may cause undesired operation.
This device contains FCC ID OMJ0015.
WEEE COMPLIANCE
9
DATALOGIC
READING DIAGRAMS
GRYPHON Mx00 (STANDARD)
0 5 10 15 20 25 30 35
-15
-10
-5
0
5
10
15
M100 (STD) - Reading Zones (10° skew angle)
(cm)
CODE 39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE 39
0.50 mm
(20 mils)
CODE 39
0.076 mm
(3 mils)
0.13 mm
(5 mils)
GRYPHON Mx00 (PDF)
0 5 10 15 20 25 30 35
-10
-5
0
5
10
M200 (PDF) - Reading Zones (10° skew angle)
(cm)
CODE39
0.076 mm
(3 mils)
CODE39
0.13 mm
(5 mils)
EAN13 M=1
0.33 mm
(13 mils)
CODE39
0.50 mm
(20 mils)
0.13 mm
(5 mils)
0 2 4 6 8 10 12 14 16
-8
-6
-4
-2
0
2
4
6
8
(cm)
M200 (PDF) - PDF417 codes, Reading Zones (10° skew angle)
PDF417 Aspect Ratio 3:1
0.25 mm
(10mils)
0.17 mm
(6.6mils)
0.38 mm
(15mils)
10
GRYPHON™ MX00
NUMERIC TABLE
Ì01Î
0
Ì12Î
1
Ì23Î
2
Ì34Î
3
Ì45Î
4
Ì56Î
5
Ì67Î
6
Ì78Î
7
Ì89Î
8
Ì9:Î
9
11
05
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
GRYPHON M100, Cordless Bar Code Reader
GRYPHON M200, Cordless Bar Code Reader
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alla Direttiva del Consiglio Europeo sottoelencata:
are in conformity with the requirements of the European Council Directive listed below:
sont conformes aux spécifications de la Directive de l'Union Européenne ci-dessous:
der nachstehenden angeführten Direktive des Europäischen Rats entsprechen:
cumple con los requisitos de la Directiva del Consejo Europeo, según la lista siguiente:
1999/5/EEC R&TTE
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
ETSI EN 301 489-3 v.1.4.1,
AUGUST 2002: ELECTROMAGNETIC COMPATIBILITY AND R
A
DIO SPECTRUM
MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC)
STANDARD FOR RADIO EQUIPMENT AND SERVICES; PART 3:
SPECIFIC CONDITIONS FOR SHORT-RANGE DEVICES (SRD)
OPERATING ON FREQUENCIES BETWEEN 9 KHZ AND 40 GHZ
ETSI EN 300 220 v.1.1.1, SEPTEMBER 2004:ELECTROMAGNETIC COMPATIBILITY AND R
A
DIO SPECTRUM
MATTERS (ERM); SHORT RANGE DEVICES (SRD); R
A
DIO
EQUIPMENT TO BE USED IN THE
25 MHZ TO 1000 MHZ
FREQUENCY RANGE WITH POWER LEVELS RANGING UP TO
500
MW; PART 3: HARMONIZED EN COVERING ESSENTIAL
REQUIREMENTS UNDER ARTICLE
3.2 OF THE R&TTE DIRECTIVE
EN 60950-1, December 2001: INFORMATION TECHNOLOGY EQUIPMENT – SAFETY
PART 1: GENERAL REQUIREMENTS
Lippo di Calderara, September 8th, 2005
Ruggero Cacioppo
Quality Assurance Laboratory Manager
Datalogic Scanning, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
©2009 Datalogic Scanning, Inc. 820000744 (Rev. F) 10/09
www.scanning.datalogic.com
Australia
Datalogic Scanning Pty Ltd
Telephone: [61] (2) 9870 3200
France and Benelux
Datalogic Scanning SAS
Telephone: [33].01.64.86.71.00
france.scanning@datalogic.com
Germany
Datalogic Scanning GmbH
Telephone: 49 (0) 61 51/93 58-0
germany.scanning@datalogic.com
India
Datalogic Scanning India
Telephone: 91- 22 - 64504739
india.scanning@datalogic.com
Italy
Datalogic Scanning SpA
Telephone: [39] (0) 39/62903.1
italy.scanning@datalogic.com
Japan
Datalogic Scanning KK
Telephone: 81 (0)3 3491 6761
japan.scanning@datalogic.com
Latin America
Datalogic Scanning, Inc
Telephone: (305) 591-3222
latinamerica.scanning@datalogic.com
Singapore
Datalogic Scanning Singapore PTE LTD
Telephone: (65) 6435-1311
singapore.scanning@datalogic.com
Iberia
Datalogic Scanning SAS Sucursal en España
Telephone: 34 91 746 28 60
spain.scanning@datalogic.com
United Kingdom
Datalogic Scanning LTD
Telephone: 44 (0) 1582 464900
uk.scanning@datalogic.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Datalogic Gryphon M200 User manual

Category
Bar code readers
Type
User manual

Datalogic Gryphon M200 is a cordless reader that offers fast and reliable barcode scanning. It features a long-lasting battery, a durable design, and a variety of configuration options. With its ability to read 1D and 2D barcodes, the Gryphon M200 is ideal for use in retail, healthcare, and other industries.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI