Harwa LC15H3 User manual

Category
LCD TVs
Type
User manual

This manual is also suitable for

Table of Contents
Important Safety Precautions..........................................................................................................................1
Preparations....................................................................................................................................................3
Using the Remote Control .....................................................................................................................3
Batteries for the Remote Control ..........................................................................................................3
Power connection ..................................................................................................................................4
Antenna Connection ..............................................................................................................................4
Identification of Controls ................................................................................................................................5
Main unit (front view).............................................................................................................................5
Main unit (rear view) ..............................................................................................................................6
Remote Control .....................................................................................................................................7
Connections....................................................................................................................................................9
Cautions before connecting ...................................................................................................................9
Connect 21-pin EURO-SCART (AV1 IN)...............................................................................................9
Connect Audio/Video inputs (AV2 IN) .................................................................................................10
Connect a PC .......................................................................................................................................11
Connect a VCR for recording or external amplifier .............................................................................12
Turning the Unit On and Off.........................................................................................................................13
Turning the Unit On and Off ................................................................................................................13
Viewing the Menus and Displays ..........................................................................................................13
Memorizing the Channels .............................................................................................................................14
Storing Channels in Memory Automatically .........................................................................................14
Storing Channels in Memory Manually .................................................................................................14
Manual Fine Tuning ...............................................................................................................................15
Adding and Erasing Channels ...............................................................................................................15
Editing Channel Name..........................................................................................................................15
Basic Operations...........................................................................................................................................16
Changing Channels ...............................................................................................................................16
Adjusting the Volume ...........................................................................................................................16
Select Input Source Signal.....................................................................................................................17
Selecting a MENU Language ................................................................................................................17
Setting Picture...............................................................................................................................................18
Customizing the Picture.......................................................................................................................18
Using the Preset Picture Mode ............................................................................................................18
Preparations (continued)
Power connection
1. Connecting the female plug to the AC socket on AC adapter.
2. Connecting the AC adapter to the DC power input of the set.
3. Connecting the male plug to the wall outlet as illustrated.
Note:
Plug into AC outlet.
Household
power outlet
AC cord
AC adapter
Connect to the DC input
socket of the product.
Be sure to insert plug into
the end fully and confirm
it is reliable
Antenna Connection
75-ohm coaxial cable (round cable)
300-ohm twin-lead flat feeder
To antenna
input terminal
( )
INSTALL the unit in a room where direct light will not fall upon
the screen. Total darkness or a reflection on the picture screen
may cause eyestrain. Soft and indirect lighting is recommended
for comfortable viewing.
Optimum reception of color requires a good signal and will
generally mean that an outdoor aerial must be used. The exact
type and position of the aerial will depend upon your particular
area.
It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio
wave conditions.
The aerial cable should not be bundled with the power cord and the like.
Note:
<
<This product should be operated only from the type of power source indicated on the marking label.
<Always unplug the AC adapter from the product and power outlet when not using for a long period of time.
Always turn the Power Switch of the LCD TV set to OFF when connecting the AC adapter.
4
Note:
1. SOURCE
To access the SOURCE select menu
2. MENU
Press this button to access the MENU main page.
3. CH +/-
Change the TV channel.
In OSD Menu, press these buttons to choose the OSD items.
4. VOL +/-
Increase or decrease the sound volume level.
In OSD Menu, press these buttons to adjust the value or setting of each item
5. POWER
Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to STANDBY.
SOURCE, MENU, CH+/-, VOL+/- and POWER on the main unit have the same functions as the corresponding buttons on
the remote control.
This operation manual provides a description based on operating functions with the remote control.
5
Identification of Controls
Main unit (front view)
Power On/
Standby
Control Panel
Power Indicator
Remote Sensor
A yellow indicator lights when the power is
on and a red indicator lights when in the
standby mode.
Speaker
Select Input Signal
Menu
Volume Down/Up
Channel Down/Up
Speaker
SOURCE MENU
CHCH VOL VOL POWER
Identification of Controls (continued)
Main unit (rear view)
DC 12V
VGA
-
PC AUDIO PHONE
RF
-
S VIDEO
(SCART
)
AV1
L
R R
AUDIO
AV2 IN AUDIO OUT
VIDEO
1 2 3 4 5 6 7 8
1. DC POWER input
Connect to the DC output of the Power Adapter.
2. VGA input /Audio in
Connect to the VGA/audio output 3.5mm jacks on your PC.
3. S-Video input
Receive a S-Video signal from external source such as VCR or DVD player.
4. AV 2 inputs (Video, Audio L, R)
Receive video/audio signals from external sources such as VCR or DVD player.
5. Headphone 3.5mm jack
6. Audio outputs (L, R)
Connect to external amplifier to enjoy high quality sound.
7. 21-pin Euro-SCART (RGB) interface: AV1input and Scart output
8. Antenna input
6
L
Connections
Cautions before connecting
Carefully check the terminals for position and type before making any connections.
The illustration of the external equipment may be different depending on your model.
Loose connectors can result in image or color problems. Make sure that all connectors are securely inserted into their
terminals.
Refer to the operating manual of the external device as well.
When connecting an external device, turn the power off to avoid any issues.
Connect 21-pin EURO-SCART (AV1 IN)
Interface on the rear of the Unit
2
4
6
8
10
12
14
16
18
20
1
3
5
7
9
11
13
15
17
19
21
21-pin Euro-SCART
connector
Decoder
21-pin Euro-SCART (RGB)
1. Audio right output 8. AV control 15. RED input
2. Audio right input 9. Earth for green 16. RGB control
3. Audio left output 10. Not used 17. Earth for video
4. Common earth for audio 11. GREEN input 18. Earth for RGB control
5. Earth for blue 12. Not used 19. Video output
6. Audio left input 13. Earth for red 20. Video input (PAL/SECAM/NTSC)
7. BLUE input 14. Not used 21. Plug shield
TV
AV1
AV2
SVIDEO
D-Sub
Video1
SOURCE
1. Turn on your LCD TV , press Source button on the remote control.
2. Press CH+/- to select AV1 and press VOL+ to confirm or wait for about 5 seconds.
3. Turn on the decoder.
4. Set the Scart Output item (in System menu) to TV and select a proper channel through
the Scart Output Channel item. For detailed operation, please refer to [Setting Scart
Output] in page19.
To watch decoder
Connect the 21-pin Euro-SCART between the unit and decoder.
How to connect:
9
DC 12V
VGA
-
PC AUDIO
PHONE
RF
-
S VIDEO
(SCART
)
AV1
L
R R
AUDIO
AV2 IN AUDIO OUT
VIDEO
L
Connections (continued)
WW
YY
RR
VCR
YY
Yellow (VIDEO)
White (AUDIO L/MONO)
Red (AUDIO R )
WW
YY
RR
Audio
cable
DC 12V
VGA
-
PC AUDIO
PHONE
RF
-
S VIDEO
(SCART
)
AV1
L R
AUDIO
AV2 IN
VIDEO
Video
cable
DVD player
WW
RR
Video Camera
Examples of external devices that can be connected
Home video
game system
Interface on the rear of the Unit
S-Video
cable
Connect Audio/Video inputs (AV2 IN)
Note:
For better video, you can use the S-video terminal if your source supports it. If you are going
to use S-video terminal, please select SVIDEO instead of AV2 in SOURCE menu.
The Video input terminal on the AV2 IN and the S-Video input terminal share the same Audio input terminals.
1. Turn on your LCD TV , press Source button on the remote control.
2. Press CH+/- to select AV2 or SVIDEO and press VOL+ to confirm or wait
for about 5 seconds.
3. Turn on the external device and play it.
To view signal from AV2 inputs
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and
external devices.
How to connect:
or
The unit provides Audio/Video inputs for you to connect external devices such as VCR, Video Camera, DVD Player or
Home video game system.
TV
AV1
AV2
SVIDEO
D-Sub
Video2
SOURCE
10
R
AUDIO OUT
L
Connect a PC
How to connect:
1. Turn on your LCD TV , press Source button on the remote
control.
2. Press CH+/- to select D-Sub (VGA IN).
3. Press VOL+ to confirm or wait for about 5 seconds.
4. Turn on your PC and check for PC system requirements.
5. Adjust the PC screen.
To Watch the PC screen
Connect a VGA cable between the VGA jack on the PC and the VGA input jack on the unit.
Connect an Audio cable between the AUDIO output on the PC and AUDIO input 3.5mm jack on the unit.
Connections (continued)
Audio
cable
VGA
cable
DC 12V
VGA
-
PC AUDIO
PHONE
RF
-
S VIDEO
(SCART
)
AV1
L R
AUDIO
AV2 IN
VIDEO
Interface on the rear of the Unit
TV
AV1
AV2
SVIDEO
D-Sub
D-Sub
SOURCE
11
AUDIO OUT
L
R
Connect a VCR for recording or external amplifier
How to connect:
Connect the 21-pin Euro-Scart between the Scart Interface on the unit and VCR.
Connect the Audio cables between the Audio (L/R) jacks on the unit and external amplifier.
- or -- or -
Note:
<
The Scart can not output VGA picture/sound signals.
<
When you use the Scart interface to record a source, you may view other source simultaneously. To do this, make sure to set the
Scart Output item to a proper selection:
-TV for recording a TV program while viewing whatever source simultaneously.
-Monitor for recording what on screen (except a VGA picture).
When Monitor is selected, you may record the source from which (e.g. AV2 or TV) the unit was switched to VGA while you may
watch a VGA source simultaneously. For detailed operation, please refer to [Setting Scart Output] in page19.
Connections (continued)
RLVIDEO
AUDIO
WW
RR
Yellow (VIDEO)
White (AUDIO L/MONO)
Red (AUDIO R )
WW
YY
RR
Audio
cable
DC 12V
VGA
-
PC AUDIO
PHONE
RF
-
S VIDEO
(SCART
)
AV1
L R
AUDIO
AV2 IN
VIDEO
Interface on the rear of the Unit
AV OUT
RLVIDEO
AUDIO
-
S VIDEO
ANT INANT OUT
AV IN
Rear of the VCR
12
21-pin Euro-SCART
connector
VCR for recording
R
AUDIO OUT
External Amplifier
WW
RR
To Audio inputs
1. Turn on your LCD TV, select a program.
2. Turn the main volume of the amplifier to minimum.
3. Turn on the amplifier and adjust for a proper volume.
To enjoy high-quality sound through an external amplifier
L
To record program (using Scart interface)
1. Turn on your LCD TV, select a program (TV or AV2) you wish to record.When select AV2, please make sure to set the
Scart Output to Monitor.
2. Turn on your VCR, insert a videotape for recording.
3. Press the Record button to begin recording.
Specifications
Type LCD TV
Display Size diagonal 15”
Display Feature
LCD panel TFT-LCD
Resolution 1024 x 768
Pixel Pitch 0.297mm
Maximum Colors 262,000
Brightness 400 nit
Contrast 500:1
o o
Viewing Angle 160 /120
Response Time 16 ms
TV System PAL/SECAM BG, DK, PAL-I, SECAM-L, SECAM-L’,
Channel Coverage
System VHF UHF CATV
PAL-D/K 1-12 13-57 Z1~Z37
PAL-B/G 2-12 21-69 X~Z+2, S1~S41
PAL-I 2-12 21-69
SECAM-B/G 2-12 21-69 X~Z+2, S1~S41
SECAM-D/K 1-12 21-69
SECAM-L 2-4
SECAM-L 5-12 21-69 X~Z C57, S1~S41
Teletext TOP/FLOF TELETEXT (10 pages)
Speaker 3W/8 ohm x 2
AC Adapter Input AC230V, 50Hz
AC Adapter Output DC12V
Power Consumption 40 W
Unit Weight (kg) 3.5
Unit Dimensions (WxHxD) (mm) 470 x 322.5 x 180
Terminals
AV1 (SCART) 21-pin EURO-SCART
AV 2 IN VIDEO, AUDIO
S-VIDEO S-VIDEO
VGA/AUDIO IN D-Sub 15-pin/3.5mm Stereo mini phone Jack
AUDIO UT L, R
HEADPHONE 3.5mm Stereo mini phone Jack
Accessories 1 User Manual,
1 AC adapter, 1 AC Power Cord
1 Remote Control, 2 AAA Batteries
1 Audio/Video Cable, 1 Audio Cable
Supported Display Format 640 x 480 @ 60Hz 640 x 480 @ 75Hz
720 x 400 @ 70Hz
800 x 600 @ 60Hz 800 x 600 @ 75Hz
1024 X 768@ 60Hz 1024 X 768@ 75Hz
29
Dimensional Drawings
Design and specifications are subject to change without notice.
30
227
280
322.5
470
55.5
171
180
English
French
Spanish
German
Italian
WIDE Mode Settings
Blue Screen
Scaler Mode
Video Standard
Audio Standard
Sleep Time
Scart Output
Off
Fill All
Auto
B/G
0 minutes
Monitor
Press VOL+/- to display System menu page.repeatedly
2
Press CH+/- to select Scaler Mode item.repeatedly
3
Press VOL+/- to select Fill All or Wide.
4
Fill All
The Fill All mode stretches the input vertically and horizontally to fill the display.
Wide
The Wide mode keeps the input signal fill the screen vertically, t and the left and
right side of picture will be .
he picture will be stretched horizontally
cropped
You can quickly select the Scaler mode by using the button.
Note:
Press MENU to display the menu main page.
1
604-L15H3S9-00
PRINTED IN
RECYCLED PAPER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Harwa LC15H3 User manual

Category
LCD TVs
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI