Briteq FT-20 Owner's manual

Brand: Briteq

Model: FT-20

Category: Fog Machine

Type: Owner's manual

FT-20 Fire Training

Fog Machine User Manual

English

User Manual - English

Safety Information

Please read the following safety information carefully before operating the

machine. This information includes important safeguards about installation,

usage, and maintenance. Pay attention to all warning labels and instructions in

this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

․ Keep this device dry.

․ Always connect to a grounded circuit to avoid risk of electrocution.

․ Remove machine from battery or power adaptor before servicing and when not in use.

․ This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,

remove machine from battery or power adaptor and clean with a damp cloth. If fluid is

spilled onto electronic parts, immediately unplug the machine and contact your local

Antari dealer for advice.

․ No user serviceable and modifiable parts inside. Never try to repair this product, an

unauthorized technician may cause damage or malfunction to the machine.

․ For adult use only. Never leave the machine running unattended.

․ Installed the machine in a well-ventilated area. Provide at least 50 cm space around the

machine.

․ Never add flammable liquid of any kind to the machine.

․ Make sure there are no flammable materials close to the machine while operating.

․ Only use Antari fluid. Other fluid may lead to heater clog and malfunction.

․ If the machine fails to work, unplug the machine and stop operation immediately.

Contact your local Antari dealer for advise.

․ Before transporting the machine, make sure the fluid tank is completely drained.

․ Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely.

In case of eye contact or if fluid is swallowed, immediately look for medical advice.

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to

ensure that all parts are present and have been received in good condition. If any parts

appear damaged or mishandled from shipping, notify the shipper immediately and retrain the

packing material for inspection.

What is included: 1 x FT-20 Fog Machine

1 x Battery base

1 x Battery charger

1 x FLM water-based liquid

1 x User Manual

1 x Flightcase

Product Dimensions

293 mm

238 mm

108 mm

Product Overview

FT-20S Power Base (Optional)

Main Power Switch

Lock lever

Charger Input

Output Level Adjustment

Knob

Wireless Receiver Socket

Wire Remote Socket

XLR 3-Pin DMX Connector

Pow

er Input

ON / OFF Switch Control

Fog Output Nozzle

Dip Switch

Setting Up

Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm

open space around the machine.

Step 2: Fill the fluid tank with Antari approved fluid.

Step 3: Charge the battery by plug the charger adaptor into a grounded electrical outlet.

Yellow light on the adaptor indicates charging, when it turn green indicate charge complete.

Please note the battery require 15 hours charge time.

Plug in charger

Yellow indicates charging

Green indicates charging

complete

Always connect the machine to a protected circuit and ensure it is properly

grounded to avoid risk of electrocution.

Step 4: Connect the battery base or power base to the machine. Turn on the machine to

start operation.

Pull to release locking lever

Align and insert head unit to base

Step 5: To start making fog, locate the rotary knob on the back for output level adjustment,

and press the button to start making fog, release to stop.

Step 6: To turn off the machine, disconnect machine from battery base or power base.

Operation

Control Panel Operation

The machine can be operated with the On/Off button and output level control knob located

on the rear. When using On/Off Mode press and hold the button to make fog, release to stop.

In Continuous Mode, press button once to make fog press again to stop.

Dip Switch 1

Function

OFF On/Off Mode

ON Continuous Mode

Rotary Knob

Function

SMOKE Turn haze on/off, adjust output volume from 0~100%

DMX Connector Pin Assignment

The machine provides 3-pin XLR connectors for DMX connection. The diagram below

indicates pin assignment information.

Pin Function

1 Ground

2 Data-

3 Data+

DMX Operation

Making the DMX Connection – Connect machine to a DMX controller or to one of the

machines in the DMX chain. The machine uses an 3-pin XLR connector for DMX connection,

the connector is located on the rear of the machine.

Address Setup – Use the DIP switch located on the rear of the machine to set the DMX

address. The machine occupies 1 control channels. The starting address is defined as the

first channel from which the machine will respond to the controller. Always double check to

make sure there are no overlapping channles in order to control the machine correctly.

DMX Channel Function

Channel 1 DMX Value Range Function

Fog

0 – 4

5 – 255

Fog Off

Output 1-100%

Z-3 Remote Control Operation (Optional)

To operate the machine by remote control, connect the remote to the microphone jack

located on the rear of machine. Use the switch to turn fog on/off, and use the rotary knob to

adjust the output volume from 0~100%.

WTR-20 Wireless Operation (Optional)

Wireless remote control system W-2 consists of a transmitter equipped with four buttons to

activate, deactivate, increase and decrease fog output and an onboard receiver attached to the

rear panel of FT-20 fog machine.

W-2 Wireless Transmitter

Press [A] button to emit fog.

Press [B] button to stop.

Press [C] button to increase output volume.

Press [D] button to decrease output volume.

In a free open space the effective distance is 50 meters, actual usage depending on obstacle

level the effective distance is 10-25 meters.

Wireless Receiver

Registering a transmitter

Transmitters can be paired or deleted from the receiver. Each receiver can pair up to 5

transmitters. Follow the steps below to pair or delete a transmitter from a receiver.

To Pair

Step 1: Put Dip switch 11 to ON position

Step 1: LED indicator will start blinking, press and hold [A] to pair

Step 2: Once pairing complete LED indicator will be constant on for 3 seconds

Step 3: Put Dip switch 11 back to OFF position to start operation.

To Delete

Step 1: Put Dip switch 10 to ON position

Step 2: LED indicator will start blinking, press and hold [A] to delete

Step 3: Delete process will take approximately 10 seconds

Step 2: Once deleting is completed LED indicator will be constant on for 3 seconds

Step 3: Put Dip switch 10 back to OFF position to start operation

Transmitter battery replacement

If the effective distance seems to decrease, it is possible the battery level is low and requires

replacement. In order to replace the battery, undo the three screws on the back of

transmitter to release the cover. Replace with same type and specification of battery which is

27A 12V

Fluid

Only use Antari FLM water-based liquid for the FT-20 Fire Training Fog

Machine. The machine is tested and calibrated with this liquid to get

the best output performance. Warranty will be void if any other type of

liquid is used, improper use of liquid may lead to machine failure and

malfunction.

Service and Maintenance

• Do not allow the machine to become contaminated.

• Remove dust from air vents with air compressor, vacuum or a soft brush.

• Only use a damp cloth to clean the casing.

• Before storing run distilled water through the system to help avoid condensing the pump

or heater.

• It is recommended to run the machine on a monthly basis in order to achieve best

performance and output condition.

• Excessive dust, liquid and dirt built up will degrade performance and cause overheating.

LED Status Indicator

Battery Care

Important information to extend the battery life:

• Fully charge the battery upon receipt of the machine.

• Every 2-4 weeks: check and ensure the battery has sufficient power to work.

• At least charge the battery to full every 4-6 months. (put a reminder in your agenda!)

• After use: have the battery fully charged within 24 hours!

• Before storage: fully charge the battery!

• Always store the machine with a fully charged battery in a cool and dry area, avoid directly sunlight.

• If you have any question on maintenance and usage, please contact your local dealer for advice.

Status LED Indicator

Standby/Ready Constant on

Producing fog Slow flash

Producing fog via DMX Alternate quick and slow flash

Low battery Quick flash

Machine error Fast flash

Technical Specifications

Voltage DC 12V (Battery)

AC 100-240V, 50 / 60Hz (Battery Charger)

Heater 600W

Warm-up time 1 sec

Max. operating time 11 min. at 100% output with battery

Fluid tank capacity 0.4 L

Fluid consumption 16 ml/min

Compatible fluid Antari FLM water-based fluid

Control option DMX 512

Manual

Wireless remote (optional)

Cable remote (optional)

DMX channels 1 channel

DMX data connection 3-pin XLR

Optional accessories WTR-20 Wireless remote

Z-3 Remote

FT-20S Power Base

Dimension L 293 x W 108 x H 238 mm

Dry weight 8.53 kg

C08FT0200

Briteq FT-20 Owner's manual

Brand: Briteq

Model: FT-20

Category: Fog Machine

Type: Owner's manual

Download PDF

report

Briteq FT-20 Owner's manual

Briteq FT-20 Owner's manual

Related papers

Other documents