Metos WD 100 GR R-L Owner's manual

Brand: Metos

Model: WD 100 GR R-L

Category: Sanitary ware

Type: Owner's manual

POTWASHER WITH GRANULATE WD-

100GR

(translation of the original documentation)

Installation and user manual

S/N: Valid from: 01.05.2012 Rev.: 3.0

4197805,4197807, 4197817

WD-100GR Rev. 3.0 (201205)

Dear Customer,

Congratulations on deciding to choose a Metos appliance for your kitchen activi-

ties. You made an excellent choice. We will do our best to make you a satisfied

Metos customer like thousands of customers we have around the world.

Please read this manual carefully. You will learn correct, safe and efficient work-

ing methods in order to get the best possible benefit from the appliance. The in-

structions and hints in this manual will give you a quick and easy start, and you

will soon note how nice it is to use the Metos equipment.

All rights are reserved for technical changes.

You will find the main technical data on the rating plate fixed to the equipment.

When you need service or technical help, please let us know the serial number

shown on the rating plate. This will make it easier to provide you with correct serv-

ice.

For your convenience, space is provided below for you to record your local Metos

service contact information.

METOS TEAM

Metos service phone number:.........................................................................

Contact person:.............................................................................................

WD-100GR Rev.

1. General information ......................................................................... 1

1.1 Symbols used in this manual ........................................................................... 1

1.2 Symbols on the dishwasher ............................................................................. 1

1.2.1 Machine marking ...................................................................................... 2

1.3 Checking that the machine and the manual correspond .................................. 2

2. Safety instructions ........................................................................... 3

2.1 General information ......................................................................................... 3

2.2 Transport .......................................................................................................... 3

2.3 Installation ........................................................................................................ 3

2.4 Detergent and drying agent ............................................................................. 4

2.5 Operation ......................................................................................................... 4

2.5.1 Hot water .................................................................................................. 4

2.5.2 Crushing risk ............................................................................................. 4

2.5.3 Risk of slipping .......................................................................................... 4

2.6 Cleaning ........................................................................................................... 4

2.6.1 Pressure washing ..................................................................................... 4

2.6.2 The outside of the machine ...................................................................... 5

2.6.3 Cleaning the floor ...................................................................................... 5

2.7 Repairing and servicing the dishwasher .......................................................... 5

2.7.1 Safety instructions if the machine is not functioning ................................. 5

2.8 Recycling the machine ..................................................................................... 5

3. Installation ........................................................................................ 6

3.1 General information ......................................................................................... 6

3.2 Requirements for the installation site ............................................................... 6

3.2.1 Lighting ..................................................................................................... 6

3.2.2 Ventilation ................................................................................................. 6

3.2.3 Drains ....................................................................................................... 6

3.2.4 Space for servicing ................................................................................... 7

3.3 Transport and storage ...................................................................................... 7

3.4 Preparing for the installation ............................................................................ 7

3.5 Unpacking ........................................................................................................ 8

3.5.1 Removing packaging ................................................................................ 8

3.6 Recycling the packaging .................................................................................. 9

3.7 Installation ........................................................................................................ 9

3.7.1 Positioning the machine ............................................................................ 9

WD-100GR Rev.

3.8 Connections ................................................................................................... 10

3.8.1 Electrical connection ............................................................................... 11

3.8.2 Water connection .................................................................................... 11

3.8.3 Drain connection ..................................................................................... 11

3.8.4 Ventilation ............................................................................................... 11

3.9 Installing auxiliary equipment ......................................................................... 12

3.10 Installing detergent and drying agent equipment ......................................... 13

3.10.1 Electrical connection of the equipment ................................................. 13

3.10.2 Detergent dosing system ...................................................................... 14

3.10.3 Drying agent dosing system ................................................................. 14

3.11 Trial operation .............................................................................................. 14

3.11.1 Start-up schedule .................................................................................. 14

3.12 Technical documentation ............................................................................. 16

4. Instructions for use ........................................................................ 17

4.1 Preparations ................................................................................................... 18

4.1.1 The machine's design ............................................................................. 18

4.1.2 Preparations before filling ....................................................................... 20

4.1.3 Filling the machine .................................................................................. 20

4.1.4 Positioning the items in the cassette ...................................................... 20

4.2 Using the machine ......................................................................................... 36

4.2.1 Washing .................................................................................................. 36

4.2.2 Starting the wash programme – washing ............................................... 38

4.2.3 Guaranteed final rinse ............................................................................ 39

4.2.4 Checking the washed items .................................................................... 39

4.2.5 Stopping the machine during operation .................................................. 40

4.2.6 Changing the water ................................................................................. 40

4.3 After use – cleaning ....................................................................................... 42

4.3.1 Daily cleaning ......................................................................................... 42

4.3.2 Periodic cleaning .................................................................................... 47

4.3.3 Periodic servicing .................................................................................... 49

4.3.4 Operating problems ................................................................................ 50

5. Technical information .................................................................... 53

WD-100GR Rev. 3.0 (201205)

General information

1. General information

Read the instructions in this manual carefully as they contain important informa-

tion regarding the correct, effective and safe installation, use and servicing of the

dishwasher.

Keep this manual in a safe place so that it can be used by other operators of the

dishwasher.

The electronics in the machine are RoHS compatible.

1.1 Symbols used in this manual

This symbol warns of situations where a safety risk may arise. The instructions

given should be followed in order to prevent injury.

This symbol on a component is a warning of electrical equipment. The machine

is sensitive to electrostatic discharge (ESD), which is why a static electricity wrist-

band must be used when handling the electronics.

This symbol explains the correct way to perform a task in order to prevent poor

results, damage to the dishwasher or hazardous situations.

This symbol identifies recommendations and hints to help you to get the best per-

formance from the machine.

This symbol explains the importance of careful and regular cleaning of the ma-

chine to meet hygiene requirements.

1.2 Symbols on the dishwasher

This symbol on a component is a warning of electrical equipment. The component

may only be removed by a qualified electrician. The machine is sensitive to elec-

trostatic discharge (ESD), which is why a static electricity wristband must be used

when handling the electronics.

WD-100GR Rev. 3.0 (201205)

General information

1.2.1 Machine marking

The machine has two rating plates, one of which is placed at the bottom of one

side of the machine and the other in the electrical cabinet. The technical informa-

tion on the plates is also included on the machine's wiring diagram. The various

rating fields show:

1. Machine type

2. Machine serial number

3. Year of manufacture

4. Enclosure protection class

5. Voltage

6. Number of phases with or without zero

7. Frequency

8. Main fuse

9. Motor output

10. Electrical heat output

11. Max. output

1.3 Checking that the machine and the manual correspond

Check that the type description on the rating plate corresponds with the type de-

scription on the front of the manual. If manuals are missing, it is possible to order

new ones from the manufacturer or the local distributor. When ordering new man-

uals, it is important to quote the machine number found on the rating plates.

S/N:

Type

Mårdvägen 4, S-352 45 V ÄXJÖ SWEDEN

marks_SAP

WD-100GR Rev. 3.0 (201205)

Safety instructions

2. Safety instructions

2.1 General information

The machine is CE marked, which means that it complies with the requirements

of the EU machinery directive with regard to product safety. Product safety means

that the design of the machine will prevent personal injury or damage to property.

Modifying the equipment without the approval of the manufacturer invalidates the

manufacturer’s product liability.

To further improve safety during installation, operation and servicing, the operator

and the personnel responsible for installing and servicing the machine should

read the safety instructions carefully.

Switch off the machine immediately in the event of a fault or malfunction. The ma-

chine must only be serviced by trained engineers. The regular checks described

in the manual must be carried out in accordance with the instructions. The ma-

chine must be serviced by a person authorised to do so by the manufacturer. Use

original spare parts. Contact an authorised service company to draw up a pro-

gramme of preventative maintenance. Dangerous situations may arise if the in-

structions above are not followed.

Before using the machine, ensure that personnel are given the necessary training

in operating and maintaining the machine.

2.2 Transport

Handle the machine with care during unloading and transport to avoid the risk of

it tipping over. Never lift or move the machine without using the wooden packag-

ing to support the stand.

2.3 Installation

This symbol on a component is a warning of electrical equipment. The machine

is sensitive to electrostatic discharge (ESD), which is why a static electricity wrist-

band must be used when handling the electronics.

Water and steam pipes must only be connected by authorised personnel.

Water pipes must be connected in a way that complies with the current regula-

tions of the local water supply authority. Check that the water and steam connec-

tions are tight before operating the machine.

Make sure that the mains voltage is the same as that indicated on the machine's

rating plate. The machine should be connected to a lockable mains switch.

WD-100GR Rev. 3.0 (201205)

Safety instructions

2.4 Detergent and drying agent

Only detergent and drying agent intended for industrial dishwashing machines

must be used. Ordinary washing-up liquid must not be used in the machine or for

soaking. Contact your detergent supplier regarding the choice of a suitable deter-

gent.

Be aware of the risk of handling washing and drying agents. Protective gloves and

safety glasses should be used when handling dishwasher detergent. Read the

warning text on the detergent and drying agent containers as well as the deter-

gent supplier's regulations.

2.5 Operation

2.5.1 Hot water

The temperature of the wash and rinse water is 58°C and 85°C. Do not open the

door until the wash and rinse phases have finished.

2.5.2 Crushing risk

Take care when opening and closing the doors, as there is a risk of body parts

being crushed between the door and the tank, and at the top of the machine be-

tween the door and the cover plate.

2.5.3 Risk of slipping

In order to prevent the risk of people slipping if granulate has been spilled on the

floor, this must be regularly swept up. Keep the floor dry and mop up any water

which has been spilled.

2.6 Cleaning

The temperature of the water in the tank is approx. 58°C and contains detergent.

Be careful when draining and cleaning the tank. Use protective gloves.

2.6.1 Pressure washing

The machine must not be cleaned with a pressure washer. If pressurised water is

directed at the electrical cabinet, the water may penetrate the cabinet and dam-

age the electrical equipment, which may affect the safety of the machine.

In order to satisfy current requirements, electrical components of approved enclo-

sure classes are used. There is no enclosure class capable of withstanding high

pressure.

WD-100GR Rev. 3.0 (201205)

Safety instructions

2.6.2 The outside of the machine

Pressure washers and hoses must not be used to wash the outside of the ma-

chine. Water can penetrate into the electrical cabinet and the control panel and

damage the equipment, which may affect the safety of the machine.

2.6.3 Cleaning the floor

When the floor is being cleaned using a pressure washer, water can splash up

under the machine and damage the components. These have not been designed

to withstand being washed with water. Never use a pressure washer to clean the

floor within 1 metre of the dishwasher without the special protective covers that

are available to prevent splashing. Problems with splashing can also occur when

using ordinary hoses.

2.7 Repairing and servicing the dishwasher

Disconnect the power supply before removing the front panel. Avoid touching hot

pipes and the booster heater.

2.7.1 Safety instructions if the machine is not functioning

Check the following:

• Has the machine been used according to the instructions?

• Are all the removable parts in the correct place?

• Is the mains switch in the ON position?

• Are the fuses in the electrical cabinet undamaged? Ask the service person-

nel to check the fuses.

If this does not solve the problem, ask authorised service personnel to check the

machine.

2.8 Recycling the machine

When the dishwasher has reached the end of its service life, it must be recycled

in accordance with current regulations. Contact professionals who specialise in

recycling.

WD-100GR Rev. 3.0 (201205)

Installation

3. Installation

3.1 General information

The machine must be installed by authorised personnel only.

Read these instructions carefully as they contain important information regarding

the correct installation method.

The instructions should be used together with the machine’s wiring diagram and

flow diagrams for water and steam.

The machine is CE marked. The CE mark is only valid for machines that have not

been modified. If the machine is damaged as a result of the instructions not being

followed, this invalidates the supplier’s warranty and product liability.

3.2 Requirements for the installation site

3.2.1 Lighting

In order to ensure the best possible working conditions during installation, opera-

tion, servicing and maintenance, make sure that the machine is installed in a well-

lit room.

3.2.2 Ventilation

The machine produces heat and steam when in operation. In order to ensure the

best possible working conditions, a certain air change rate is required in the dish-

washing room. The ventilation requirements for the room should be calculated on

the basis of current standards.

3.2.3 Drains

There must be a floor drain with an effective trap for the machine's waste water

and for water used for cleaning. The drain should be located under the machine's

loading bench. The floor drain capacity can be found in the TECHNICAL SPECI-

FICATIONS.

WD-100GR Rev. 3.0 (201205)

Installation

3.2.4 Space for servicing

A 1-metre area should be left clear in front of the machine for servicing purposes.

The area above the machine must not contain any equipment which could pre-

vent the fitting, servicing and replacement of parts.

3.3 Transport and storage

Always transport the machine in an upright position.

Take care during transport, as there is a risk of the machine tipping over.

NOTE: The machine must not be transported without a pallet or other support.

Some form of support beam must always be used along the sides of the machine

during transport, otherwise the machine may be damaged. When transporting the

machine without a normal wooden pallet, always check that none of the compo-

nents underneath the machine can be damaged.

A=Pumps

B=Spacers

If the machine is not being installed immediately, it must be stored in a frost-free

area where the air is dry.

3.4 Preparing for the installation

The machine supplied with a height for transport purposes of 2300 mm.

Check that there is sufficient height available to transport the machine to its instal-

lation site.

Check that the overheating protection on booster heaters and tank elements is

set to zero.

WD-100GR Rev. 3.0 (201205)

Installation

3.5 Unpacking

Check against the delivery note that all the units have been delivered.

Remove the packing material. Inspect the machine for any transport damage.

3.5.1 Removing packaging

The packaging consists of a frame on which the machine rests, beams that hold

the frame together, two beams as protection for the pumps and two thin boards

that hold the spacer blocks in place.

The packaging is screwed together using wooden screws. This is why a battery-

powered screwdriver is recommended.

1. Remove the two thin boards (35).

2. Remove the external beam on the electrical cabinet side (33).

3. Remove all the screws (36) on the internal beam by the machine’s electri-

cal cabinet side.

4. Unscrew the beam at the rear of the machine (33).

5. Remove both of the protective beams for the pumps (34).

6. Lift the machine (from the rear) using a truck and remove the beams at the

sides of the machine (31).

7. Place the machine on its feet.

Inspect the machine for any transport damage.

demont

WD-100GR Rev. 3.0 (201205)

Installation

3.6 Recycling the packaging

Packaging must be disposed of or recycled in accordance with local regulations.

3.7 Installation

3.7.1 Positioning the machine

Remove the protective plastic on the sides which will be put against the wall.

Loosen the detergent hose on the back of the machine before putting the machine

against the wall. Hang the hose up in such a way that it is easily accessible for

the detergent supplier.

Put the machine in position and check that it is horizontal using a spirit level. Lat-

eral tilt: Place a spirit level on the body of the machine at the infeed and outfeed.

The machine’s longitudinal direction: Place the spirit level across the body of the

machine.

Once the machine has been filled with water, check that it is level.

Adjust the height using the machine's legs.

WD-100GR Rev. 3.0 (201205)

Installation

3.8 Connections

*) The condensing fan runs for 10 seconds at the start of the wash cycle and for

50 seconds from 10 seconds after the final rinse has started.

1. Cold water connection

2. Hot water connection

3. Electrical connection

4. Steam connection (Option)

5. Condensation connection (Option)

6. Drain connection

7. Connection for detergent hose

8. Ventilation requirements of the machine

WD-100GR Rev. 3.0 (201205)

Installation

3.8.1 Electrical connection

This symbol on a component is a warning of electrical equipment. The part may

only be removed by a qualified electrician or trained personnel.

Information about electrical connections can be found on the machine's wiring di-

agrams. The wiring diagrams are inside the electrical cabinet door. Store the di-

agrams in the electrical cabinet after installation.

The machine must be connected to a lockable mains switch. This should be po-

sitioned on the wall where it is protected from the water and steam which may be

released when the door is opened.

The machine is equipped with a phase sequence detector. The machine will not

start if the phase sequence is incorrect. If the phase sequence is incorrect, the

display will show POWER SUPPLY FAILURE CHECK THE EMERGENCY

SWITCH.

The connection in the electrical cabinet is at (3).

3.8.2 Water connection

Connect the cold and hot water pipes according to the labels by the connection

points (1,2). If the machine is connected to a hose, the internal diameter of the

hose must be at least 12 mm.

The hot water connection is fitted with a filter. The cold water connection is fitted

with a filter, non-return valve and vacuum valve. The connections have an internal

thread.

A stopcock must be installed on the water supply pipes.

It is important that the water supply has sufficient pressure to ensure the correct

flow of water to the machine. The required pressure can be found in the TECH-

NICAL SPECIFICATIONS. If the water pressure is too low, a booster pump must

be fitted.

3.8.3 Drain connection

The waste water system connected to (6) must have 50 mm metal pipes that will

withstand collision or 50 mm plastic pipes. The waste water pipe must be con-

nected to a floor drain and the opening of the pipe must be above the water level.

The capacity of the floor drain must be 3 litres/second.

3.8.4 Ventilation

The machine has a condensing battery connected to an exhaust fan to reduce the

amount of steam released. Extractor fans for extracting steam can be installed

above the infeed and outfeed openings, as well as above the area of the machine

where steam is emitted from the condensing fan.

If a hood is fitted over the machine, it must cover both the infeed and the outfeed.

The front of the hood must be positioned at least 500 mm in front of the machine

to allow access for service and repairs.

WD-100GR Rev. 3.0 (201205)

Installation

3.9 Installing auxiliary equipment

Once the machine is in place and adjusted horizontally and vertically, the auxiliary

equipment can be fitted.

• The loading bench (A) and extension bench (B) can be put in place. The

height of the extension bench (B) can be adjusted where it connects to the

machine. When the water and electricity supplies etc. have been connect-

ed and it is possible to open the doors, check that the cassette (C) can eas-

ily be slid into the machine.

• If necessary, fix two of the legs on the loading bench to the floor. Drill

through the rubber plate.

• Adjust the height of the trolley (D) and check that the cassette can easily

be transferred from the trolley to the loading bench.

• If necessary, the outfeed opening can be adjusted so that it is slightly high-

er than the infeed opening.

• Guide the plastic wheel on the side of the trolley into the guide rail (E) on

the console under the outfeed opening.

• Adjust the height of the roller (F) between the trolley and the machine.

Auxiliary equipment

• A=Bench

• B=Extension bench

• C=Cassette

• D=Trolley

• E=Guide rail

• F=Roller

WD-100GR Rev. 3.0 (201205)

Installation

3.10 Installing detergent and drying agent equipment

The machine comes ready for fitting detergent and drying agent equipment, but

this is not included with the machine.

To avoid making unnecessary holes in the machine, the equipment should be

placed on the wall behind the machine on the outfeed side.

Connecting detergent and drying agent

• A=Water outlet for detergent

• B=Drying agent connection

• C=Junction box

3.10.1 Electrical connection of the equipment

• Remove the cover plate under the electrical cabinet. The panel is fixed with

screws at the bottom edge under the stand.

• The terminal block for connecting the dosing equipment is in the junction

box (C) inside the cover plate. The FU/DM circuit breaker for the equipment

is in the electrical cabinet. (For connection information, see the wiring dia-

gram).

• A hole for fitting a measuring cell can be found in the tank. Remove the

sealing plug and insert the measuring cell into the existing hole.

WD-100GR Rev. 3.0 (201205)

Installation

3.10.2 Detergent dosing system

• The water outlet (A) for the detergent dosing system is on the incoming hot

water pipe.

• The hose on the back of the machine is connected to a container for deter-

gent. The hose, which is supplied with the machine, is connected to the

wash tank.

3.10.3 Drying agent dosing system

The connection for drying agent (B) is located next to the booster heaters.

3.11 Trial operation

Prepare the machine for trial operation by following the INSTRUCTIONS FOR

USE. The instructions describe the measures that must be taken to prepare the

machine for operation.

3.11.1 Start-up schedule

This should be completed and signed by the customer on start-up.

Machine type:

Machine serial number:

Installation date:

Customer:

Address for visitors:

Postcode + Town/City:

Telephone:

Contact:

Dealer:

Telephone:

Contact:

Installation company:

Telephone:

Contact:

Service company:

Telephone:

Detergent supplier:

Telephone:

End user’s signature:

Name in block capitals:

WD-100GR Rev. 3.0 (201205)

Installation

Read the installation and user manuals carefully. Then check the following points:

1. Check:

• That the wires to the doors are properly seated on all wire wheels.

• Water and drain connections.

• That the machine is evenly balanced.

• That the cassette can easily be moved in and out of the machine.

• Detergent and drying agent.

• That the pump filters, level pipe and tank filter are in position.

• That the FU21, FU41 and FU42 mini-switches are in the off position.

• The machine is connected with the correct phase sequence. NOTE: The

machine will not start if the phase sequence is incorrect. If the phase se-

quence is incorrect (QM15 must be switched on), the display will show

“POWER SUPPLY FAILURE CHECK THE EMERGENCY SWITCH”.

• The pump’s direction of rotation. NOTE: If the direction of rotation is wrong,

the phase must be inverted on the terminal block for the incoming electrical

cable.

• That there is the right quantity of granulate in the machine.

• The overheating protection is set to zero.

2. Filling the machine:

• Turn on the power switch.

• Close the doors.

• Fill the machine with water in accordance with the maintenance instruc-

tions. NOTE: There must not be a cassette in the machine.

• When "HEATING IN PROGRESS TEMPERATURE IN TANK" appears on

the display, FU21, FU41 and FU42 are switched on.

3. Check the setting of the reference values:

• Check the functioning of the booster pump, where applicable.

• All the reference values are set to the recommended values on delivery.

4. Run a number of washes complete with loads and check that:

• There are no water leaks.

• The switch for the doors is working.

• The anti-crushing mechanism is working.

• The water temperatures are maintained.

• The washed items are clean.

• There is no granulate sticking to the washed items.

• The washed items are dried.

• There is an adequate water flow to the machine. Recommended setting: 6

l/wash cycle Flow: 15 l/min. This can be checked in the machine's refer-

ence values and diagnostics function.

5. Final check: Empty the machine and turn off the power using the power switch.

• Re-tighten all the connections on the circuit breakers and relays.

• Set all the circuit breakers to the on position

• Inform the customer if the water flow and the water pressure are too low.

• Display the maintenance instructions supplied with the machine.

6. Train the dishwashing staff

WD-100GR Rev. 3.0 (201205)

Installation

3.12 Technical documentation

To ensure that the machine is used correctly, it is essential that the documenta-

tion supplied with the machine is made available to the staff who will be using the

machine. The installation and user manuals should be kept near the machine.

If the service manual is supplied with the machine, it should be given to the serv-

ice engineer who is responsible for the machine.

If the spare parts manual is supplied with the machine, it should be given to the

service engineer who is responsible for the machine.

If the WEB Tool manual is supplied with the machine, it must be kept near the ma-

chine.

Page is loading ...

Metos WD 100 GR R-L Owner's manual

Brand: Metos

Model: WD 100 GR R-L

Category: Sanitary ware

Type: Owner's manual

Download PDF

report

Metos WD 100 GR R-L Owner's manual

Metos WD 100 GR R-L Owner's manual

Related papers

Other documents