Extron DTP DVI 301 User manual
- Category
- Console extenders
- Type
- User manual
Extron DTP DVI 301 is a digital video extender that allows you to extend a DVI signal up to 330 feet (100 m) using a single Cat5e/6/7 cable. It supports resolutions up to 1920x1200 and is HDCP compliant, making it ideal for use in a variety of applications, including home theater, digital signage, and video conferencing.
The DTP DVI 301 features a number of advanced features, including:
- DDC pass-through: Allows the display to communicate with the source device, ensuring that the optimal video settings are used.
- EDID emulation: Stores the EDID (Extended Display Identification Data) of the display, ensuring that the source device always sends the correct video signal.
Extron DTP DVI 301 is a digital video extender that allows you to extend a DVI signal up to 330 feet (100 m) using a single Cat5e/6/7 cable. It supports resolutions up to 1920x1200 and is HDCP compliant, making it ideal for use in a variety of applications, including home theater, digital signage, and video conferencing.
The DTP DVI 301 features a number of advanced features, including:
- DDC pass-through: Allows the display to communicate with the source device, ensuring that the optimal video settings are used.
- EDID emulation: Stores the EDID (Extended Display Identification Data) of the display, ensuring that the source device always sends the correct video signal.
DTP DVI 301 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron DTP DVI 301 digital video extender. The DTP 301 transmitter and receiver pair can extend
a DVI signal up to 330 feet (100 m).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
DTP DVI 301 Tx
DTP DVI 301 Rx
INPUTS
LOCAL OUTPUT
AUDIO
DVI-D
DTP DVI 301 Tx
L R
OUTPUTS
DVI-D
AUDIO
DTP DVI 301 Rx
RxTx
RS-232 IR
RxTx
POWER
12V
0.7 A MAX
IN
ANALOG AUDIO
SIG LINK
DTP IN
DTP DVI
30
1 T
x
DTP DVI
30
1 R
x
RxTx
RS-232 IR
RxTx
LOCAL
SHARE
REMOTE
1 2
ON
DDC ROUTE
POWER
12V
0.7 A MAX
OUT
ANALOG AUDIO
SIG LINK
DTP OUT
FrontRear
4
8
8
1 23
5
FrontRear
4 7
6
5
Step 2 — Connections
a
DVI Input connector (Tx) — Connect a DVI cable between this port and the DVI output port of the digital video source.
b
Local Output connector (Rx) — If desired, connect a DVI monitor for local monitoring of the input digital image.
c
Audio input (Tx) — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.
d
RS-232 and IR connectors — To pass serial or infrared data or control signals, such as
serial control of a projector, connect the master device to the transmitter and the slave
device to the receiver via the RS-232 and IR captive screw connectors on both units.
e
DTP and Analog Audio (Output and Input) RJ-45 connectors — Connect one or
two TP cables between these RJ-45 female connectors on the transmitter and receiver.
à
DTP connector (required) — Connect transmitter DTP Out to receiver DTP In.
This cable carries:
z TMDS (digital) video z Bidirectional RS-232 and IR commands and data
z Embedded audio z Remote power
Sig(nal) LED — This LED lights when the unit is receiving a TMDS clock signal on the
DVI input (transmitter) or any valid signal on the DTP In connector (receiver).
Link LED — This LED lights when a valid link is established between the units on the
DTP cable.
â
Analog Audio connector (optional) — Connect transmitter Analog Audio Out to
receiver Analog Audio In. This cable carries analog audio only and is not needed for
applications that do not require this audio signal.
Terminate all cable ends in accordance with the same standard, either TIA/EIA T 568 A or TIA/EIA T 568 B.
CAUTION: Do not connect these devices to a computer data or telecommunications network.
NOTE: You can check the DTP Out to DTP In cable connection as follows:
1. Plug a cable into the DTP jack on the powered unit.
2. Connect the opposite end of the cable into the DTP jack on the unpowered unit.
If the DTP Link LED and the Power LED on the unpowered unit are lit, the connection is correct.
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
TIA/EIA T
568 A
TIA/EIA T
568 B
Blue
TP Wires
12345678
Pins:
Ground
Receive pin on connected unit
Transmit pin on connected unit
Connected RS-232
and IR Device Pins
Tx/Rx
Pins
Receive pin on connected unit
Transmit pin on connected unit
RxTx
RS-232 IR
RxTx
1
2
f
DVI Output connector (Rx) — Connect a display with a DVI input for display of the transmitted direct digital image.
g
Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio
captive screw connector. See the drawing below.
Unbalanced Stereo Output Balanced Stereo Output
LR
Ring
Sleeve(s)
Tip
Tip
Ring
LR
Sleeve(s)
Tip
Tip
Do not tin the wires!
CAUTION: Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.
h
Power connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz
source. Connect the power supply to either unit as shown at right.
CAUTION: This product is intended to be supplied by a Listed Power Unit
marked “Class 2” or “LPS,” rated 12 VDC, 1.0 A minimum.
Always use a power supply supplied by or specified by Extron.
Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply
and the end product. Unless otherwise stated, the AC/DC
adapters are not suitable for use in air handling spaces or in
wall cavities. The installation must always be in accordance
with the applicable provisions of National Electrical Code
ANSI/NFPA 70, article 75 and the Canadian Electrical Code
part 1, section 16. The power supply shall not be permanently
fixed to a building structure or similar structure.
NOTE: Only one power supply is required. A single power supply
connected to either unit in the pair powers both units. A power
supply is included with each transmitter.
Operation
LOCAL
SPARE
REMOTE
1 2
ON
DDC ROUTE
POWER
12V
0.7 A MAX
Rear
(Tx)
Front
(Both Units)
ANAL
2 3
1
After all devices are powered up, the system is fully operational. See the
definitions of the power indications (shown at right), below:
a Power LED (front panel) —
Amber — The unit is receiving power, either locally or remotely (on the
DTP cable).
Green — The unit is powered on and is receiving an active DVI signal, either on the DVI input if a transmitter, or transmitted on
the DTP cable if a receiver.
b Power LED (rear panel) —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
c DC Route switch — This rear panel switch selects either the remote or local DVI display as the display data channel (DDC)
reference for EDID and HDCP communication.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the
Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
68-2169-50
Rev A
08 11
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada
Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics. All rights reserved. www.extron.com
DTP DVI 301 • Setup Guide (Continued)
-
1
-
2
Extron DTP DVI 301 User manual
- Category
- Console extenders
- Type
- User manual
Extron DTP DVI 301 is a digital video extender that allows you to extend a DVI signal up to 330 feet (100 m) using a single Cat5e/6/7 cable. It supports resolutions up to 1920x1200 and is HDCP compliant, making it ideal for use in a variety of applications, including home theater, digital signage, and video conferencing.
The DTP DVI 301 features a number of advanced features, including:
- DDC pass-through: Allows the display to communicate with the source device, ensuring that the optimal video settings are used.
- EDID emulation: Stores the EDID (Extended Display Identification Data) of the display, ensuring that the source device always sends the correct video signal.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron electronics DTP DVI 301 User manual
-
Extron electronics DTP HDMI 301 User manual
-
Extron DTP DVI 4K 230 Tx User manual
-
Extron electronics DTP DVI 4K 330 Tx User manual
-
Extron SMD 202 Owner's manual
-
-
-
Extron electronics DTP HDMI 4K 330 Rx User manual
-
Extron DTP HDMI 4K 230 Rx User manual
-
Extron electronics DTP HDMI 301 User manual
