Installation Instructions for the
RPNR090KAAA3A11X
Hall-Effect Rotary Position Sensor
ISSUE 1
50035271
Sensing and Control
GENERAL INFORMATION
The RPN Series Rotary Position Sensors use a magnetically
biased, Hall-effect integrated circuit (IC) to accurately sense
rotary movement of the actuator shaft. Rotation of the actuator
shaft changes the IC’s position relative to the magnets. The
resulting flux density change is converted to a linear output.
MOUNTING INFORMATION
Mount the sensor using the two easily accessible mounting
holes. Mounting screw tightening torque is 2,5 N m ±0,5 N m
[22.1 in lb ±4.4 in lb].
Table 1. Output Signals
Channel 1 Channel 2
Angle Output Angle Output
L (-45°) 0.25 Vdc
L (-45°)
4.75 Vdc
0° 2.5 Vdc 0° 2.5 Vdc
R (+45°) 4.75 Vdc R (+45°) 0.25 Vdc
Figure 1. Mounting and Dimensional Diagram (For
Reference Only mm/[in].)
249155
RPNR090KAAA3A11X
4.75 Vdc 0.25 Vdc
WW/YY
L R
90°
27,7
[1.09]
40,8
[1.61]
50
[1,97]
63
[2.48]
24,8
[0.98]
14
[0.55]
4,12
[0.16]
8,3
[0.33]
5
[0.20]
56
[2.20]
4,6
[0.18]
Ø20
[0.79]
Ø6
[0.24]
Ø2
[0.08]
Channel 1
1 = 0 V
2 = 10 Vdc to 30 Vdc Supply
3 = 0.25 Vdc to 4.75 Vdc
Angle (°)
Output (Vdc)
0
0.25
4.75
45 45
Characteristic Curve
2.5 Vdc
4.75 Vdc0.25 Vdc
1 2 3 4 5 6
Channel 2
4 = 0 V
5 = 10 Vdc to 30 Vdc
6 = 4.75 Vdc to 0.25 Vdc Output
Output (Vdc)
4.75
0.25
Channel 1 Channel 2
Pinout
Ø5.3
[0.20]
Receptacle: AMP 1-1419168-1
Mating Connector: AMP 1438199-2
Table 2. Specifications
Characteristic Parameter
Supply voltage:
Channel 1
Channel 2
10 Vdc to 30 Vdc
10 Vdc to 30 Vdc
Current consumption 20 mA max.
Output signal delay 3 ms approx.
Accuracy ±1.6%
Hysteresis none
Linearity ±2°
Reverse polarity protection yes
Operating and storage temperature range -40 °C to 125 °C [-40 °F to 257 °F]
EMC 200 V/m ISO 11452-3
Expected life 30x10
6
cycles
Protection class IP69K DIN 40050
Housing material PA66 plastic
Shaft material stainless steel
Mechanical end stop no
RPNR090KAAA3A11
Issue 1 50035271
Sensing and Control
Honeywell
1985 Douglas Drive North
Minneapolis, MN 55422
www.honeywell.com/sensing
50035271-1-EN IL50 GLO Printed in USA
October 2008
Copyright © 2008 Honeywell International Inc. All rights reserved.
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific +65 6355-2828
+65 6445-3033 Fax
Europe +44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin America +1-305-805-8188
+1-305-883-8257 Fax
USA/Canada +1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
/