Vanguard Heating 000 User manual

Brand: Vanguard Heating

Model: 000

Category: Fireplaces

Type: User manual

This manual is also suitable for

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a ﬁre or explosion may result causing

property damage, personal injury, or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency, or the gas supplier.

MODELS VMH26TPC AND VMH26TNC

14,000 to 26,000 Btu/Hr with Thermostat

VENT-FREE COMPACT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

Shown with Optional Cabinet Mantel/Hearth Base Accessory

www.desatech.com

113111-01D

WARNING: Improper installation, adjustment, altera-

tion, service, or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualiﬁed installer, service

agency, or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses

air (oxygen) from the room in which it is installed. Provi-

sions for adequate combustion and ventilation air must

be provided. Refer to Air for Combustion and Ventilation

section on page 6 of this manual.

This appliance may be installed in an aftermarket,* per-

manently located, manufactured (mobile) home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indi-

cated on the rating plate. This appliance is not convert-

ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety Information ............................................... 3

Local Codes ........................................................ 4

Product Identiﬁcation ...........................................

Product Features ................................................. 5

Unpacking ........................................................... 5

Assembly ............................................................. 5

Air for Combustion and Ventilation ...................... 6

Installation ........................................................... 9

Operating Fireplace ........................................... 19

Inspecting Burner .............................................. 21

Cleaning and Maintenance ................................ 22

Troubleshooting ................................................. 23

Service Hints ..................................................... 27

Technical Service ..............................................

Speciﬁcations ....................................................

Replacement Parts ............................................ 27

Illustrated Parts Breakdown and Parts List ....... 28

Accessories ....................................................... 30

Warranty Information ...........................

Back Cover

State of Massachusetts: The installation must be made by a licensed plumber or gas ﬁtter in the

Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-ﬁred supplemental room heaters shall provide to each

purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for bedroom and bathroom installation in the Common

wealth of Massachusetts.

www.desatech.com

113111-01D 3

SAFETY INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects,

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate, or service this ﬁreplace.

Improper use of this ﬁreplace

can cause serious injury or death

from burns, fire, explosion,

electrical shock, and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the ﬂu, with head

aches, dizziness, or nausea. If you have these signs,

the ﬁreplace may not be working properly. Get

fresh air at once! Have ﬁreplace serviced. Some

people are more affected by carbon monoxide than

others. These include pregnant women, people with

heart or lung disease or anemia, those under the

inﬂuence of alcohol, and those at high altitudes.

Natural and Propane/LP Gas: Natural and propane/LP

gases are odorless. An odor-making agent is added

to these gases. The odor helps you detect a gas leak.

However, the odor added to the gas can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all warnings.

Keep this manual for reference. It is your guide to

safe and proper operation of this ﬁreplace.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not allow fans

to blow directly into the ﬁreplace.

Avoid any drafts that alter burner

ﬂame patterns. Ceiling fans can

create drafts that alter burner

ﬂame patterns. Altered burner

patterns can cause sooting.

WARNING: Do not use a

blower insert, heat exchanger

insert, or other accessory not

approved for use with this ﬁre

place.

Due to high temperatures, the

appliance should be located out

of trafﬁc and away from furniture

and draperies.

Do not place clothing or other

ﬂammable material on or near

the appliance. Never place any

objects in the ﬁreplace.

Fireplace front and screen be

come very hot when running ﬁre-

place. Keep children and adults

away from hot surfaces to avoid

burns or clothing ignition. Fire-

place will remain hot for a time

after shutdown. Allow surfaces

to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with ﬁreplace.

You must operate this ﬁreplace

with the ﬁreplace screen and

hood in place. Make sure ﬁre-

place screen is in place before

running ﬁreplace.

Keep the appliance area clear

and free from combustible ma

terials, gasoline, and other ﬂam

mable vapors and liquids.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This ap

pliance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) in

side any structure. Locate propane/LP supply

tank(s) outdoors (propane/LP only).

www.desatech.com

113111-01D

SAFETY INFORMATION

Continued

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs

instructions

• if you cannot reach your gas supplier, call

the ﬁre department

4. This ﬁreplace shall not be installed in a bed

room or bathroom.

5. Do not use this ﬁreplace as a wood-burning

ﬁreplace. Use only the logs provided with the

ﬁreplace.

6. Do not add extra logs or ornaments such as

pine cones, vermiculite, or rock wool. Using

these added items can cause sooting. Do not

add lava rock around base. Rock and debris

could fall into the control area of ﬁreplace.

7. This ﬁreplace is designed to be smokeless. If logs

ever appear to smoke, turn off ﬁreplace and call

a qualiﬁed service person. Note: During initial

operation, slight smoking could occur due to

log curing and ﬁreplace burning manufacturing

residues.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 22.

9. Before using furniture polish, wax, carpet

cleaner, or similar products, turn heater off.

If heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

10. This ﬁreplace needs fresh air ventilation to run

properly. This ﬁreplace has an Oxygen Deple

tion Sensing (ODS) safety shutoff system. The

ODS shuts down the ﬁreplace if not enough

fresh air is available. See Air for Combustion

and Ventilation, page 6. If ﬁreplace keeps

shutting off, see Troubleshooting, page 23.

11. Do not run ﬁreplace

• where ﬂammable liquids or vapors are used

or stored.

• under dusty conditions.

12. Do not use this ﬁreplace to cook food or burn

paper or other objects.

13. Do not use ﬁreplace if any part has been under

water. Immediately call a qualiﬁed service

technician to inspect the room ﬁreplace and to

replace any part of the control system and any

gas control which has been under water.

14. Turn off and unplug ﬁreplace and let cool

before servicing. Only a qualiﬁed service

person should service and repair ﬁreplace.

15. Operating ﬁreplace above elevations of 4,500

feet could cause pilot outage.

16. Do not operate ﬁreplace if any log is broken.

Do not operate ﬁreplace if a log is chipped

(dime-sized or larger).

17. To prevent performance problems, do not use

propane/LP fuel tank of less than 100 lbs.

capacity (propane/LP only).

18. Provide adequate clearances around air

openings.

LOCAL CODES

Install and use ﬁreplace with care. Follow all local

codes. In the absence of local codes, use the lat

est edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT

IDENTIFICATION

Figure 1 - Vent-Free Gas Compact

Fireplace

Ignitor Button

Screen

Fireplace

Cabinet

Logs

Control Knob

www.desatech.com

113111-01D 5

PRODUCT FEATURES

SAFETY PILOT

This ﬁreplace has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

ﬁreplaces. The ODS/pilot shuts off the ﬁreplace if

there is not enough fresh air.

PIEZO IGNITION SYSTEM

This ﬁreplace has a piezo ignitor. This system

requires no matches, batteries, or other sources

to light ﬁreplace.

THERMOSTATIC HEAT CONTROL

This ﬁreplace has a thermostat sensing bulb and a

control valve. The thermostat will automatically

modulate the heat output to maintain a consistent

room temperature. This results in greater ﬁreplace

comfort. This can also result in lower gas bills.

UNPACKING

1. Remove fireplace and hood from carton.

Log is wrapped and inside ﬁreplace. Do not

remove at this time.

2. Remove all protective packaging applied to

ﬁreplace for shipment.

3. Make sure your ﬁreplace includes one hard

ware packet.

4. Check ﬁreplace for any shipping damage. If

ﬁreplace is damaged, promptly inform dealer

where you bought ﬁreplace.

ASSEMBLY

WARNING: Always have

branch support and screen in

place before operating ﬁreplace.

This prevents excessive temper-

atures on ﬁreplace surfaces.

WARNING: Failure to position

the parts in accordance with these

diagrams or failure to use only

parts speciﬁcally approved with

this ﬁreplace may result in prop-

erty damage or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

• Phillips screwdriver

• 5/16" hex wrench

• slotted screwdriver

Installing Log

1. Lift screen up and pull out to remove.

2. Cut two plastic straps to remove the log from

the ﬁrebox cavity.

An optional blower is available. See Accessories,

page 30. Install optional blower now. Follow

installation instructions provided with blower.

4. Remove log packaging material and discard

packaging. Gently place log set on burner

support (see Figure 2). The log should ﬁt ﬂat

against top of burner support and log locator

tabs ﬁt into the slots under the log. Do not

allow log to contact ﬂame. If ﬂame contacts

log, soot will be created.

Figure 2 - Assembling Fireplace

Log

Screen

Burner Support

with Log

Locator Tabs

Branch

Support

Shoulder

Screw

www.desatech.com

113111-01D

ASSEMBLY

Continued

5. Reattach screen by placing the notches in the

screen frame over the shoulder screws and

pushing down.

Assembling Hood

1. Locate four black phillips sheet metal screws

from the hardware packet.

2. Rotate hood as shown in Figure 3. Make sure

hood tabs point toward ﬁreplace.

3. Insert hood tabs between bafﬂe and louvers

(see Figure 3).

4. Gently rotate hood to upright position. Make

sure hood tabs are behind louvers and hood

is resting on ﬁrebox top (see Figure 3).

5. Align screw holes on hood with screw holes

on ﬁrebox top.

6. Insert screws as shown in Figure 3. Tighten

screws ﬁrmly.

Figure 3 - Assembling Hood

Hood

Louver

Hood Tab

Bafﬂe

Sheet Metal

Screw

Firebox Top

Hood Tabs

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a conﬁned

space or unusually tight construc

tion unless provisions are provid

ed for adequate combustion and

ventilation air. Read the following

instructions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Todayʼs homes are built more energy efﬁcient

than ever. New materials, increased insulation, and

new construction methods help reduce heat loss

in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy efﬁ

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, ﬁreplaces, clothes dryers, and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/ NFPA 54, Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol

lowing ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on pages 6 through 8 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion and

ventilation. However, in buildings of unusually

tight construction, you must provide additional

fresh air.

www.desatech.com

113111-01D 7

Unusually tight construction is deﬁned as

construction where:

a. walls and ceilings exposed to the out

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10

-11

kg per pa-sec-m

) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and ﬂoors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical, and gas lines,

and at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh

air. See Ventilation Air From Outdoors

page 8.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Fireplace Location.

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1.3/

NFPA 54 deﬁnes a conﬁned space as a space whose

volume is less than 50 cubic feet per 1,000 Btu

per hour (4.8 m

per kw) of the aggregate input

rating of all appliances installed in that space and

an unconﬁned space as a space whose volume is

not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m

per kw) of the aggregate input rating of

all appliances installed in that space. Rooms com

municating directly with the space in which the

appliances are installed*, through openings not

furnished with doors, are considered a part of the

unconﬁned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

AIR FOR COMBUSTION

AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Conﬁned or

Unconﬁned Space

Use this work sheet to determine if you have a

conﬁned or unconﬁned space.

Space: Includes the room in which you will install

ﬁreplace plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft.

(volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume

of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free ﬁreplace ___________

Btu/Hr

Gas water heater* ___________

Btu/Hr

Gas furnace ___________

Btu/Hr

Vented gas heater ___________

Btu/Hr

Gas ﬁreplace logs ___________

Btu/Hr

Other gas appliances* + ___________

Btu/Hr

Total = ___________

Btu/Hr

* Do not include direct-vent gas appliances. Di

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater ____________

Btu/Hr

Vent-free ﬁreplace + ___________

Btu/Hr

Total = ___________

Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_________

Btu/Hr (maximum the space can support)

_________

Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space

can support)

56,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conﬁned space

because the actual Btu/Hr used is more than the maxi

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

30,000

26,000

56,000

www.desatech.com

113111-01D

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconﬁned

space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila

tion Air From Outdoors.

C. Install a lower Btu/Hr ﬁreplace, if lower Btu/Hr

size makes room unconﬁned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support,

the space is an un-

conﬁned space. You will need no additional fresh

air ventilation.

WARNING: If the area in

which the heater may be oper-

ated is smaller than that deﬁned

as an unconﬁned space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conﬁned space. When ventilating to an adjoining

unconﬁned space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the ﬂoor on the wall connecting

the two spaces (see options 1 and 2, Figure 4). You

can also remove door into adjoining room (see

option 3, Figure 4). Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or

ducts. You must provide two permanent openings:

one within 12" of the ceiling and one within 12"

of the ﬂoor. Connect these items directly to the

outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the attic

will activate the power vent.

Figure 5 - Ventilation Air from Outdoors

Shown with Optional Mantel

Outlet

Air

ntilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

ntilated

Crawl Space

Crawl

Space

To Attic

Figure 4 - Ventilation Air from Inside

Building Shown with Optional Mantel

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

www.desatech.com

113111-01D 9

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualiﬁed ser-

vice person must install ﬁre

place. Follow all local codes.

WARNING: Never install the

ﬁreplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other ﬂammable

objects are less than 36 inches

from the front, top, or sides of

the ﬁreplace

• as a ﬁreplace insert

• in high trafﬁc areas

• in windy or drafty areas

CAUTION: This ﬁreplace cre-

ates warm air currents. These

currents move heat to wall sur

faces next to ﬁreplace. Installing

ﬁreplace next to vinyl or cloth

wall coverings or operating

ﬁreplace where impurities (such

as, but not limited to, tobacco

smoke, aromatic candles, clean-

ing ﬂuids, oil or kerosene lamps,

etc.) in the air exist, may discolor

walls or cause odors.

IMPORTANT: Vent-free ﬁreplaces add moisture

to the air. Although this is beneﬁcial, installing ﬁre

place in rooms without enough ventilation air may

cause mildew to form from too much moisture. See

Air for Combustion and Ventilation,

page 6.

Note: Your Vanguard ﬁreplace is designed to

be used in zero clearance installations. Wall or

framing material can be placed directly against

any exterior surface of your fireplace, except

where standoff spacers are integrally attached.

If standoff spacers are attached to your ﬁreplace,

these spacers can be placed directly against wall

or framing materials.

Use the dimensions shown for rough openings to

create the easiest installation (see Built-In Fire

place Installation, page 10).

CHECK GAS TYPE

Use only the correct type of gas (natural or pro-

pane/LP). If your gas supply is not the correct gas

type, do not install heater. Call dealer where you

bought heater for proper type heater.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

INSTALLATION ITEMS

Before installing ﬁreplace, make sure you have

the items listed below.

• external regulator - propane/LP only (supplied

by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection*

• ground joint union

• sediment trap

• tee joint

• pipe wrench

* A CSA design-certiﬁed equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. Purchase the optional CSA

design-certiﬁed equipment shutoff valve from your

dealer. See

Accessories, page 30.

Note: If desired, purchase a four-sided trim kit for

built-in installations. See Accessories, page 30.

www.desatech.com

113111-01D

LOCATING FIREPLACE

WARNING: Maintain the

minimum clearances shown

in Figures 6 and 7. If you can,

provide greater clearances from

ﬂoor, ceiling, and joining wall.

You can recess ﬁrebox into the wall. You can

also position ﬁreplace in the optional cabinet or

corner mantels. IMPORTANT: Only use optional

cabinet or corner mantels speciﬁed in this manual.

Purchase the optional mantel from your dealer (see

Accessories, page 30).

INSTALLATION

Continued

Figure 7 - Mounting Clearances As

Viewed From Front of Fireplace Shown

with Optional Mantel

Top Of

Mantel Can

Be Flush

With W

all

Left

Side

CEILING

Right

Side

36"

Minimum

From

Sides Of

Fireplace

Left

Side

CEILING

36"

Minimum

FLOOR

Right

Side

0” Minimum

To Top

Surface Of

Carpeting,

Tile Or Other

Combustible

Material

0" Minimum

To Top

Surface Of

Carpeting,

Tile Or Other

Combustible

Material

Figure 6 - Mounting Clearances As

Viewed From Front of Fireplace Shown

Built-In the Wall

Note: When installing ﬁreplace directly on carpet-

ing, tile or other combustible material, other than

wood ﬂooring, the ﬁreplace shall be installed on a

metal or wood panel extending the full width and

depth of the ﬁreplace.

CAUTION: If you install the

ﬁreplace in a home garage

• fireplace pilot and burner must be

at least 18 inches above ﬂoor.

• locate ﬁreplace where moving

vehicle will not hit it.

For convenience and efﬁciency, install ﬁreplace

• where there is easy access for operation, inspec

tion, and service.

• in coldest part of room.

An optional blower kit is available from your dealer

(see Accessories, page 30). If planning to use

blower, locate ﬁreplace near an electrical outlet.

BUILT-IN FIREPLACE

INSTALLATION

Built-in installation of this fireplace involves

installing ﬁreplace into a framed-in enclosure.

This makes the front of ﬁreplace ﬂush with wall.

An optional trim kit accessory is available (see

Accessories, page 30). Trim will extend past sides

of ﬁreplace approximately 1/2 inch. This will cover

the rough edges of the wall opening. If installing

a built-in mantel above the ﬁreplace you must

follow the clearances shown in Figure 11, page

12. Follow the instructions below to install the

ﬁreplace in this manner.

Actual Framing

Height 26" 26

/8"

Front Width 26

/4" 26

/8"

Depth 9

/2" 10

/2"

Bottom 3/4"

3/4"

1. Frame in rough opening. Use dimensions

shown in Figure 8, page 11, for the rough

opening.

If installing in a corner, use dimensions shown

in Figure 9, page 11, for the rough opening.

The height is 26

/8" which is the same as the

wall opening above.

www.desatech.com

113111-01D 11

WARNING: Do not allow any

combustible/noncombustible

materials to overlap the ﬁrebox

front facing.

WARNING: Do not allow

noncombustible materials to

cover any necessary openings

like louvered slots.

WARNING: Never modify or

cover the louvered slots on the

front of the ﬁrebox.

WARNING: If pre-wiring, do

not connect wiring to any electri-

cal source at this time.

Install ﬁreplace electrical outlet

and connect wiring to outlet

before connecting to electrical

source. The ﬁreplace electri-

cal outlet is included with the

GA3450T blower accessory.

Only use the ﬁreplace electri-

cal outlet supplied with the

GA3450TA blower accessory.

2. If installing GA3450TA blower accessory, do

so at this time. See Installing Blower Acces

sory GA3450TA,

page 13.

Note: If not installing blower accessory, you

may wish to run electrical wiring to your

ﬁreplace for future blower installation (see

Accessories, page 30) Use only approved

three-wire electrical wiring.

Note: A qualiﬁed installer should make all

electrical connections.

3. Install gas piping to ﬁreplace location. This

installation includes an approved ﬂexible gas

line (if allowed by local codes) after the equip

ment shutoff valve. The ﬂexible gas line must

be the last item installed on the gas piping.

4. If you have not assembled ﬁrebox, follow

instructions on page 4.

5. Carefully set ﬁreplace in front of rough opening

with back of ﬁreplace inside wall opening.

6. Attach ﬂexible gas line to ﬁreplace gas regula

tor. See Connecting to Gas Supply,

page 16.

7. Bend four nailing ﬂanges on outer casing with

pliers (see Figure 10).

8. Attach fireplace to wall studs using nails

or wood screws through holes in nailing

ﬂange.

9. Check all gas connections for leaks. See

Checking Gas Connections, page 18.

10. If using optional trim kit, install the trim after

ﬁnal ﬁnishing and/or painting of wall. See

instructions included with trim accessory for

attaching trim.

IMPORTANT: When finishing your firebox,

combustible materials

INSTALLATION

Continued

/8"

/4"

/8"

Figure 9 - Rough Opening for Installing

in Corner

/8"

3/4" Off

The Floo

Minimum

Figure 8 - Rough Opening for Installing

in Wall

Figure 10 - Attaching Fireplace to Wall

Studs

Nails or

Wood

Screws

Nailing

Flanges

www.desatech.com

113111-01D

Mantel Clearances for Built-In

Installation

If placing mantel above built-in ﬁreplace, you

must meet minimum clearance between mantel

shelf and top of ﬁreplace opening.

NOTICE: Surface temperatures

of adjacent walls and mantels be-

come hot during operation. Walls

and mantels above the ﬁrebox

may become hot to the touch.

If installed properly, these tem-

peratures meet the requirement

of the national product standard.

Follow all minimum clearances

shown in this manual.

NOTICE: If your installation does

not meet the minimum clear-

ances shown in Figure 11, you

must do one of the following:

• raise the mantel to an accept-

able height

• remove the mantel

INSTALLATION

Continued

OPTIONAL MANTEL INSTALLATION

Refer to instructions provided with the mantel

for assembly instructions. Refer to the follow

ing instructions for system installation. Refer to

instructions on page 6 for hood assembly. Blower

accessory should be installed prior to mantel if

it is being used (see Installing Optional Blower

Accessory GA3450TA, page 13).

1. Assemble cabinet mantel as shown in acces

sory instruction sheet.

2. If blower is installed, install a properly

grounded, 120 volt three-prong electrical out

let at ﬁreplace location if an outlet is not there.

If possible, locate outlet so cabinet mantel will

cover it when installed (see Figure 12).

3. Place hearth base against wall at installation

location. Cut an access hole in hearth base to

run gas line to ﬁreplace (see Figure 12). Make

sure to locate access hole so cabinet mantel will

cover it when installed. Note: You can secure

base to ﬂoor using wood screws. Countersink

screw heads and putty over.

4. Route ﬂexible gas line through access hole in

hearth base.

5. Center cabinet mantel on hearth base (see Figure

13, page 13). Make sure mantel is ﬂush against

wall and centered left to right on base.

6. Use screws provided with mantel accessory

to attach mantel assembly to base (see mantel

instruction sheet).

7. Attach ﬂexible gas line to ﬁreplace gas regula

tor. See Connecting to Gas Supply,

page 16.

8. Route electrical cord(s) through access holes

in either side of ﬁreplace with bushing. Plug

electrical cord(s) into electrical outlet.

9. Check all gas connections for leaks. See

Checking Gas Connections, page 18.

10. Carefully insert ﬁreplace into cabinet mantel (see

Figure 13, page 13). Be careful not to scratch or

damage hearth base or cabinet mantel.

13"

16"

19"

21"

10"

Note:

ll vertical

measurements

are from top of

fireplace

opening to

bottom of

mantel shelf. All

measurements

are in inches.

Figure 11 - Minimum Mantel Clearances

for Built-In Installation

Mantel Shelf

Side of

Firebox

Figure 12 - Placing Hearth Base Against Wall

Hearth

Base

Electrical

Outlet

Pipe and Gas

Shutoff Valve

www.desatech.com

113111-01D 13

INSTALLATION

Continued

11. Place metal trim on shoulder screws located

on the side and top of the ﬁreplace (see Assem

bling Perimeter Trim). Firmly snap trim over

shoulder screws. Align ﬁreplace in mantel

assembly so the trim overlaps mantel evenly

on all three sides.

12. Lower bottom louver door. Use 3" wood

screws provided with mantel accessory to at

tach ﬁreplace to base (see mantel instruction

sheet).

Side

Trim

Top Trim

Mitered Edge

Figure 14 - Assembling Perimeter Trim

Shim

Set Screws

Adjusting

Plate

Slot

Assembling Perimeter Trim (Trim

Shipped with Mantel)

1. Remove packaging from three remaining

pieces of trim.

2. Locate two adjusting plates with set screws,

and two shims in the hardware packet.

3. Align shim under adjusting plate as shown in

Figure 14.

4. Slide one end of adjusting plate/shim in slot

on mitered edge of top trim (see Figure 14).

Figure 15 - Removing Upper Louver

Assembly

Upper Louver

Assembly

Black

Screws

Blower Bracket

Mounting Holes

Removing Valve Cover Shield

1. Open bottom louver assembly by swinging

the assembly down (see Figure 16, page 14).

2. Using short Phillips screwdriver, remove

the screw under the center of the branch

support. Rotate valve cover shield clockwise

and slide out.

IMPORTANT: Do not remove shoulder screw

on the left side of valve cover shield. Slide the

valve cover shield off of the shoulder screw

(see Figure 16, page 14).

Note: If you do not have a short Phillips

screwdriver, the screen, log set, and branch

support must be removed so a longer screw

driver may be used. See Connecting Equip

ment Shutoff Valve to Heater Control, page

17, steps 1 and 2.

Figure 13 - Installing Fireplace into

Mantel Assembly

5. Slide other end of adjusting plate/shim in slot

on mitered edge of side trim (see Figure 14).

6. While ﬁrmly holding edges of trim together,

tighten both set screws on the adjusting plate

with slotted screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set trim assembly aside for later installation.

INSTALLING BLOWER ACCESSORY

GA3450TA

Removing Upper Louver Assembly

To install the blower accessory, you must ﬁrst

remove the upper louver assembly.

1. Lift screen off heater.

2. Remove 4 screws from louver assembly (see

Figure 15). Save these screws.

3. Pull louver assembly straight out from the

cabinet. Be careful not to scratch the paint.

Set louver assembly and screws aside.

www.desatech.com

113111-01D

INSTALLATION

Continued

Figure 16 - Removing Valve Cover Shield

Remove

Screw

Valve

Cover

Shield

Shoulder

Screw

Branch Support

Snap Bushings

Bottom Louver

Assembly

sembly to the outer casing with 4 #10 screws

provided (see Figure 17).

6. Route the wire harness through the hole in

left side of bafﬂe. Pull wire harness through

lower opening above where the valve shield

was removed (see Figure 17).

7. Insert the 4 wire harness into one of the round

holes in the rear of the valve cover shield and

through the rectangular hole in the front of

shield (see Figure 17).

8. Reconnect red wire to switch position 3.

Reconnect blue wire to switch position 1.

Reconnect green and white wires.

9. Install the switch plate on the valve cover

shield with 2 #10 screws provided (see Figure

17). Reinstall the valve cover shield. Route

power cord out of the cabinet by inserting

it through the bushing on the outer casing

(see Figure 17). Plug fan kit into 120-Volt

grounded power supply and test operation.

Note: When switch is in the AUTO position,

the fan will start after the heater has run for

a few moments. The fan will continue to run

for several moments after the heater has been

turned off. When switch is in the ON position,

the fan will run until turned to OFF. Reinstall

upper louver assembly and hood if previously

removed, (see Figure 15, page 13). Close

lower louver door.

Installing Blower Assembly

CAUTION: Label all wires

prior to disconnection when

servicing controls. Wiring errors

can cause improper and danger-

ous operation.

CAUTION: Verify proper op-

eration after servicing.

Note: If you are using a mantel with your heater,

use the following instructions. If your heater is

built-in, see For Built-In Installation on page 15.

1. Install snap bushings found in hardware kit

into both holes in rear of valve cover shield.

2. Make sure the wire harness is ﬁrmly con

nected to the terminals on the blower bracket

assembly.

3. Note the wire locations on back of AUTO/

OFF/ON switch. The terminals on back of

switch are numbered 1, 2, and 3. Carefully

remove red wire from terminal 1 and blue

wire from terminal 3. Black wire can remain

on middle terminal 2 (see Figure 17).

4. Carefully disconnect green and white wires at

their insulated connectors.

5. In top of the heater cabinet, locate the four

mounting holes on the outer casing. Align

these four holes with those on the blower

bracket assembly. Attach blower bracket as

Figure 17 - Installing Blower Bracket

Assembly

Wire

Harness

Blower Bracket

Assembly

Screw

Valve Cover

Shield

Box Cover

Wire

Harness

Switch

Plate

Switch

Bafﬂe

Wiring Routing

Hole in Bafﬂe

Blue

Red

Power

Cord

www.desatech.com

113111-01D 15

Figure 20 - Installing Blower Bracket

Assembly

INSTALLATION

Continued

Figure 18 - Installing Switch Plate to

Valve Cover Shield

Switch

Plate

Screw

Valve Cover

Shield

For Built-In Installation

WARNING: A licensed elec-

trician must connect the wiring

harness to electrical supply

following all local codes. Electri-

cian must provide a clamp on the

box cover to secure the wiring.

Wiring should be routed through

the bushing in the hole on the

outer casing of heater.

Follow instructions Removing Valve Cover Shield

(page 13), then

1. Install a snap bushing found in hardware kit

into one of the holes found on rear of valve

cover shield. The other hole is for a strain

relief clamp (not supplied) to secure incoming

electrical supply.

2. Follow steps 2 through 6 in Installing Blower

Assembly, page 13. Also remove black wire

from middle switch terminal 2.

3. Remove black plastic strain relief and power

cord from switch plate. The power cord supplied

will not be used in built-in installations. Pop in

the plastic snap bushing found in hardware kit

into the hole left by supply cord/strain relief.

4. A licensed electrician must follow the wiring

diagram to connect incoming electrical supply

to fan kit wiring harness (see Figure 19).

5. Plug power cord to the outlet receptacle (not

provided) as shown in Figure 18. Wind the

extra power cord and tie it up with the plastic

wire strap (see Figure 20). Set the power cord

bundle between the burner bracket and outer

casing, away from the burner.

6. Reinstall valve cover shield.

7. Test to make sure the blower is working

properly.

8. Reinstall upper louver assembly and hood if

previously removed, (see Figure 15, page 13).

Close lower louver door.

Red

Fan Switch

(Auto/Off/On)

Blue

Thermostat

Switch

(N.O.)

Green

White

Green

White

0/115

A.C.

Blower

Motor

Black

Auto

Figure 19 - Wiring Diagram For Blower

Accessory Built-In Installation

Blower Bracket

Assembly

Screw

Wire Harness

Power

Cord

Valve

Cover

Shield

Box Cover

Wire

Harness

Switch Plate

Switch

Clamp Connector

(not included)

Outlet

Receptacle

Blue

Red

Plastic

Wire Strap

www.desatech.com

113111-01D

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING: This appliance

requires a 45° male ﬂare ﬁtting

5/8"-18 UNF (Uniﬁed National Fine

Thread) inlet connection and the

ﬂexible gas line provided.

WARNING: A qualified

service person must connect

ﬁreplace to gas supply. Follow

all local codes.

CAUTION: Never connect pro-

pane/LP ﬁreplace directly to the

propane/LP supply. This ﬁreplace

requires an external regulator

(not supplied). Install the external

regulator between the ﬁreplace

and propane/LP supply.

WARNING: Never connect

natural gas ﬁreplace to private

(non-utility) gas wells. This

gas is commonly known as

wellhead gas.

For propane/LP units, installer must supply an

external regulator. The external regulator will

reduce incoming gas pressure. You must reduce

incoming gas pressure to between 11 and 14

inches of water. If you do not reduce incoming gas

pressure, ﬁreplace regulator damage could occur.

Install external regulator with the vent pointing

down as shown in Figure 21. Pointing the vent

down protects it from freezing rain or sleet.

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" or greater diameter to allow

proper gas volume to ﬁreplace.

If pipe is too small, undue loss

of volume will occur.

Installation must include a equipment shutoff valve,

union, and plugged 1/8" NPT tap. Locate NPT tap

within reach for test gauge hook up. NPT tap must

be upstream from ﬁreplace (see Figure 22).

IMPORTANT: Install equipment shutoff valve

in an accessible location. The equipment shutoff

valve is for turning on or shutting off the gas to

the appliance.

Propane/LP

Supply Tank

External

Regulator

Figure 21- External Regulator with Vent

Pointing Down

Vent

Pointing

Down

Figure 22 - Gas Connection

CSA Design-Certiﬁed

Equipment Shutoff Valve

With 1/8" NPT Tap*

PROPANE/LP

From External

Regulator (11" W.C.

to 14" W.C. Pressure)

NATURAL

From Gas Meter

(5" W.C. to

10.5" W.C.

Pressure)

3" Minimum

Pipe Cap Tee

Nipple Joint

Sediment Trap

* Purchase the optional CSA design-certified

equipment shutoff valve from your dealer. See

Accessories, page 30.

Extension Cord

Use extension cord if needed. The cord must have

a three-prong, grounding plug and a three-hole

receptacle. Make sure cord is in good shape. It must

be heavy enough to carry the current needed. An

undersized cord will cause a drop in line voltage. This

will result in loss of power and overheating. Use a No.

16 AWG cord for lengths less than 50 feet.

www.desatech.com

113111-01D 17

INSTALLATION

Continued

Figure 23 - Removing Log Base

Assembly From Fireplace

Branch

Support

Screen

Shipping

Screw

Shoulder

Screw

Flexible

Gas Line

Check your building codes for any special re-

quirements for locating equipment shutoff valve

to ﬁreplaces.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could result

in clogged ﬁreplace valves.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

CONNECTING EQUIPMENT SHUTOFF

VALVE TO HEATER CONTROL

Installation Items Needed

• Phillips screwdriver

• sealant (resistant to propane/LP gas, not pro

vided)

1. To remove fireplace screen, remove two

screws that hold ﬁreplace screen in place for

shipping. These screws are located near top of

screen. Discard screws. Lift ﬁreplace screen

up and pull out to remove.

2. Remove screws that attach branch support

to ﬁreplace (see Figure 23). Carefully lift up

branch support and remove from ﬁreplace (see

Figure 23).

3. Route ﬂexible gas line included from ﬁreplace

control to equipment shutoff valve through

side or rear access holes in outer casing.

NOTICE: Most building codes do

not permit concealed gas con-

nections. A ﬂexible gas line is

provided to allow accessibility

from the ﬁreplace (see Figure 23).

The ﬂexible gas supply line con-

nection to the equipment shutoff

valve should be accessible.

CAUTION: Avoid damage to

regulator. Hold gas regulator

with wrench when connecting it

to gas piping and/or ﬁttings.

Apply pipe joint sealant lightly to male threads of

gas connector attached to ﬂexible gas line/equip-

ment shutoff valve (see Figure 24).

5. Check all gas connections for leaks. See

Checking Gas Connections, page 18.

6. Replace branch support back into ﬁreplace.

Feed ﬂexible gas line into ﬁreplace base area

while replacing branch support. Make sure

the entire ﬂexible gas line is in ﬁreplace base

area. Reattach branch support to ﬁreplace with

screws removed in step 2.

Figure 24 - Attaching Flexible Gas Line

to Equipment Shutoff Valve

Flexible Gas Line

from Fireplace Gas

Regulator Provided

with Fireplace

To Fireplace Gas

Regulator

Equipment Shutoff

Valve Provided by

Installer

PROPANE/LP

To External Regulator

NATURA

To Gas Supply

www.desatech.com

113111-01D

INSTALLATION

Continued

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and

external to unit, for leaks after

installing or servicing. Correct

all leaks at once.

WARNING: Never use an

open ﬂame to check for a leak.

Apply a noncorrosive leak detec-

tion ﬂuid to all joints. Bubbles

forming show a leak. Correct all

leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

ﬁreplace. See guidelines under Con-

necting to Gas Supply, page 16.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect appliance with its appliance main

gas valve (control valve) and equipment shut-

off valve from gas supply piping. Pressures

in excess of 1/2 psig will damage ﬁreplace

regulator.

2. Cap off open end of gas pipe where equipment

shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve for

propane/LP gas or opening main gas valve

located on or near gas meter for natural gas,

or using compressed air.

4. Check all joints of gas supply piping system.

Apply a noncorrosive leak detection ﬂuid to

gas joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff valve

to gas supply. Check reconnected ﬁttings for

leaks.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 25).

2. Pressurize supply piping system by either

opening propane/LP supply tank valve for

propane/LP gas or opening main gas valve

located on or near gas meter for natural gas,

or using compressed air.

3. Check all joints from gas meter for natural or

propane/LP supply to equipment shutoff valve

(see Figures 26 and 27). Apply a noncorrosive

leak detection ﬂuid to gas joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

Figure 26 - Checking Gas Joints for

Propane/LP Gas (Shown with Optional

Mantel)

Figure 25 - Equipment Shutoff Valve

Equipment

Shutoff Valve

Propane/LP

Supply Tank

Figure 27 - Checking Gas Joints for

Natural Gas (Shown with Optional Mantel)

Equipment

Shutoff Valve

Gas Meter

Open

Closed

Equipment

Shutoff

Valve

www.desatech.com

113111-01D 19

INSTALLATION

Continued

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a ﬁre or explosion may result

causing property damage, per

sonal injury or loss of life.

A. This appliance has a pilot which must be

lighted by hand. When lighting the pilot,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next

to the ﬂoor because some gas is heavier than

air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neighborʼs phone. Follow the gas

supplierʼs instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

C. Use only your hand to push in or turn the

gas control knob. Never use tools. If the

knob will not push in or turn by hand, donʼt

try to repair it, call a qualiﬁed service tech-

nician or gas supplier. Force or attempted

repair may result in a ﬁre or explosion.

D. Do not use this appliance if any part has

been under water. Immediately call a

qualiﬁed service technician to inspect the

appliance and to replace any part of the

control system and any gas control which

has been under water.

LIGHTING

INSTRUCTIONS

WARNING: You must operate

this ﬁreplace with the ﬁreplace

screen in place. Make sure ﬁre

place screen is installed before

running ﬁreplace.

NOTICE: During initial operation

of new ﬁreplace, burning logs

will give off a paper-burning

smell. Orange ﬂame will also be

present. Open window to vent

smell. Operate ﬁreplace on HI

position to burn off odor. This

will only last a few hours.

1. STOP! Read the safety information starting

in column 1.

2. Make sure equipment shutoff valve is fully

open.

3. Turn control knob clockwise

to the

OFF position.

4. Wait ﬁve (5) minutes to clear out any gas.

Then smell for gas, including near the ﬂoor.

If you smell gas, STOP! Follow “B” in the

safety information starting in column 1. If

you donʼt smell gas, go to the next step.

5. Turn control knob counterclockwise

to the PILOT position. Press in control knob

for ﬁve (5) seconds (see Figure 28, page 20).

Note: You may be running this ﬁreplace for

the ﬁrst time after hooking up to gas sup

ply. If so, the control knob may need to be

pressed in for 30 seconds or more. This will

allow air to bleed from the gas system.

• If control knob does not pop up when

released, contact a qualiﬁed service person

or gas supplier for repairs.

PRESSURE TESTING FIREPLACE GAS

CONNECTIONS

1. Open equipment shutoff valve (see Figure 25,

page 18).

2. Open main gas valve located on or near gas

meter for natural gas or open propane/LP

supply tank valve.

3. Make sure control knob of ﬁreplace is in the

OFF position.

4. Check all joints from equipment shutoff

valve to thermostat gas valve (see Figures 26

and 27, page 18). Apply a noncorrosive leak

detection ﬂuid to gas joints. Bubbles forming

show a leak.

5. Correct all leaks at once.

6. Light ﬁreplace (see Operating Fireplace).

Check all other internal joints for leaks.

7. Turn off ﬁreplace (see To Turn Off Gas to

Appliance, page 20).

8. Replace front panel.

www.desatech.com

113111-01D

6. With control knob pressed in, push down

and release ignitor button. This will light

pilot. The pilot is attached to the front of

burner. If needed, keep pressing ignitor

button until pilot lights.

Note: If pilot does not stay lit, refer to

Troubleshooting, page 23. Also contact a

qualiﬁed service person or gas supplier for

repairs. Until repairs are made, light pilot

with match. To light pilot with match, see

Manual Lighting Procedure.

7. Keep control knob pressed in for 30 seconds

after lighting pilot. After 30 seconds, release

control knob.

Note: If pilot goes out, repeat steps 3

through 7. This ﬁreplace has a safety in

terlock system. Wait one (1) minute before

lighting pilot again.

8. Turn control knob counterclockwise

to desired heating level. The main burner

should light. Set control knob to any heat

level between HI and LO.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

OPERATING FIREPLACE

Continued

Ignitor Button

Figure 28 - Control Knob In The OFF

Position

Control Knob

Thermocouple

Pilot Burner

Figure 29 - Pilot (Propane/LP Shown)

Ignitor Electrode

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1. Turn control knob clockwise to the

OFF position.

2. Turn off all electric power to the appliance

if service is to be performed.

Shutting Off Burner Only (pilot stays lit)

Turn control knob clockwise

to the

PILOT position.

THERMOSTAT

CONTROL OPERATION

The thermostatic control used on this ﬁreplace

differs from standard thermostats. Standard ther

mostats simply turn on and off the burner. The

thermostat used on this ﬁreplace senses the room

temperature. The thermostat adjusts the amount of

gas ﬂow to the burner. This increases or decreases

the burner ﬂame height. At times the room may

exceed the set temperature. If so, the burner will

shut off. The burner will cycle back on when room

temperature drops below the set temperature.

The control knob can be set to any heat level

between HI and LO.

Note: The thermostat sensing bulb measures

the temperature of air near the ﬁreplace cabinet.

This may not always agree with room tempera

ture (depending on housing construction, instal

lation location, room size, open air temperatures,

etc.). Frequent use of your ﬁreplace will let you

determine your own comfort levels.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 5 under Lighting

Instructions, starting on page 19, column 1.

2. With control knob pressed in, strike match.

Hold match to pilot until pilot lights.

3. Keep control knob pressed in for 30 seconds

after lighting pilot. After 30 seconds, release

control knob. Now follow step 8 under

Lighting Instructions, column 1.

Page is loading ...

Vanguard Heating 000 User manual

Brand: Vanguard Heating

Model: 000

Category: Fireplaces

Type: User manual

This manual is also suitable for

Download PDF

report

Vanguard Heating 000 User manual

This manual is also suitable for

Vanguard Heating 000 User manual

Related papers

Other documents