Miller DS-2 Owner's manual

DS-2

Processes

Description

MIG (GMAW) Welding

Wire Feeder

OM-227 675A

2006−03

Visit our website at

www.MillerWelds.com

Flux Cored (FCAW) Welding

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Arc Welding Hazards 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Additional Symbols For Installation, Operation, And Maintenance 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. California Proposition 65 Warnings 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 − DEFINITIONS 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1. Warning Label Definitions 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-2. Symbols And Definitions 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 − INSTALLATION 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. Specifications 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. Site Selection 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. Equipment Connection Diagrams 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4. Installing Wire Guides And Drive Rolls 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-5. 6-Pin Plug PLG8 Information 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-6. 5-Pin Plug PLG1 Information 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-7. Connecting 6-Pin Plug And Shielding Gas 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-8. Connecting Weld Cable 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-9. Connecting Welding Gun 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-10. Installing Wire Spool And Adjusting Hub Tension 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-11. Threading Welding Wire 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 − OPERATION 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Pendant Controls 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 − MAINTENANCE & TROUBLESHOOTING 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Routine Maintenance 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Troubleshooting 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 − ELECTRICAL DIAGRAM 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7 − PARTS LIST 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WARRANTY

OM-227 675 Page 1

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

som _3/05

Y Warning: Protect yourself and others from injury — read and follow these precautions.

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards

with this procedure! The possible hazards are shown in

the adjoining symbols.

Y Marks a special safety message.

. Means “Note”; not safety related.

This group of symbols means Warning! Watch Out! possible

ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.

Consult symbols and related instructions below for necessary actions

to avoid the hazards.

1-2. Arc Welding Hazards

Y The symbols shown below are used throughout this manual to

call attention to and identify possible hazards. When you see

the symbol, watch out, and follow the related instructions to

avoid the hazard. The safety information given below is only

a summary of the more complete safety information found in

the Safety Standards listed in Section 1-5. Read and follow all

Safety Standards.

Y Only qualified persons should install, operate, maintain, and

repair this unit.

Y During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic wire welding, the

wire, wire reel, drive roll housing, and all metal parts touching the

welding wire are electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

D Do not touch live electrical parts.

D Wear dry, hole-free insulating gloves and body protection.

D Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

D Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

D Use AC output ONLY if required for the welding process.

D If AC output is required, use remote output control if present on

unit.

D Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

D Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

D Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

D Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

D When making input connections, attach proper grounding conduc-

tor first − double-check connections.

D Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

D Turn off all equipment when not in use.

D Do not use worn, damaged, undersized, or poorly spliced cables.

D Do not drape cables over your body.

D If earth grounding of the workpiece is required, ground it directly

with a separate cable.

D Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

D Do not touch electrode holders connected to two welding ma-

chines at the same time since double open-circuit voltage will be

present.

D Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

D Wear a safety harness if working above floor level.

D Keep all panels and covers securely in place.

D Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

D Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

D Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists in inverter-type

welding power sources after removal of input

power.

D Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section

before touching any parts.

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

D Keep your head out of the fumes. Do not breathe the fumes.

D If inside, ventilate the area and/or use local forced ventilation at the

arc to remove welding fumes and gases.

D If ventilation is poor, wear an approved air-supplied respirator.

D Read and understand the Material Safety Data Sheets (MSDSs)

and the manufacturer’s instructions for metals, consumables,

coatings, cleaners, and degreasers.

D Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

D Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

D Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and while wearing an air-supplied

respirator. The coatings and any metals containing these elements

can give off toxic fumes if welded.

OM-227 675 Page 2

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from the

weld.

ARC RAYS can burn eyes and skin.

D Wear an approved welding helmet fitted with a proper shade of fil-

ter lenses to protect your face and eyes when welding or watching

(see ANSI Z49.1 and Z87.1 listed in Safety Standards).

D Wear approved safety glasses with side shields under your

helmet.

D Use protective screens or barriers to protect others from flash,

glare and sparks; warn others not to watch the arc.

D Wear protective clothing made from durable, flame-resistant mate-

rial (leather, heavy cotton, or wool) and foot protection.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

WELDING can cause fire or explosion.

D Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

D Do not weld where flying sparks can strike flammable material.

D Protect yourself and others from flying sparks and hot metal.

D Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

D Watch for fire, and keep a fire extinguisher nearby.

D Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

D Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

D Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock, sparks, and fire

hazards.

D Do not use welder to thaw frozen pipes.

D Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

D Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

D Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL can injure eyes.

D Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

D Wear approved safety glasses with side

shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

D Shut off shielding gas supply when not in use.

D Always ventilate confined spaces or use

approved air-supplied respirator.

HOT PARTS can cause severe burns.

D Do not touch hot parts bare handed.

D Allow cooling period before working on gun or

torch.

D To handle hot parts, use proper tools and/or

wear heavy, insulated welding gloves and

clothing to prevent burns.

MAGNETIC FIELDS can affect pacemakers.

D Pacemaker wearers keep away.

D Wearers should consult their doctor before

going near arc welding, gouging, or spot

welding operations.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

D Wear approved ear protection if noise level is

high.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

CYLINDERS can explode if damaged.

D Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, physical damage, slag, open flames, sparks, and arcs.

D Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

D Keep cylinders away from any welding or other electrical circuits.

D Never drape a welding torch over a gas cylinder.

D Never allow a welding electrode to touch any cylinder.

D Never weld on a pressurized cylinder − explosion will result.

D Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and

associated parts in good condition.

D Turn face away from valve outlet when opening cylinder valve.

D Keep protective cap in place over valve except when cylinder is in

use or connected for use.

D Use the right equipment, correct procedures, and sufficient num-

ber of persons to lift and move cylinders.

D Read and follow instructions on compressed gas cylinders,

associated equipment, and Compressed Gas Association (CGA)

publication P-1 listed in Safety Standards.

OM-227 675 Page 3

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near

combustible surfaces.

D Do not install unit near flammables.

D Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

D Use lifting eye to lift unit only, NOT running

gear, gas cylinders, or any other accessories.

D Use equipment of adequate capacity to lift and

support unit.

D If using lift forks to move unit, be sure forks are

long enough to extend beyond opposite side of

unit.

OVERUSE can cause OVERHEATING

D Allow cooling period; follow rated duty cycle.

D Reduce current or reduce duty cycle before

starting to weld again.

D Do not block or filter airflow to unit.

STATIC (ESD) can damage PC boards.

D Put on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to

store, move, or ship PC boards.

MOVING PARTS can cause injury.

D Keep away from moving parts.

D Keep away from pinch points such as drive

rolls.

WELDING WIRE can cause injury.

D Do not press gun trigger until instructed to do

so.

D Do not point gun toward any part of the body,

other people, or any metal when threading

welding wire.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

D Have only qualified persons remove doors,

panels, covers, or guards for maintenance as

necessary.

D Reinstall doors, panels, covers, or guards

when maintenance is finished and before re-

connecting input power.

READ INSTRUCTIONS.

D Read Owner’s Manual before using or servic-

ing unit.

D Use only genuine Miller/Hobart replacement

parts.

H.F. RADIATION can cause interference.

D High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

D Have only qualified persons familiar with

electronic equipment perform this installation.

D The user is responsible for having a qualified electrician prompt-

ly correct any interference problem resulting from the installa-

tion.

D If notified by the FCC about interference, stop using the

equipment at once.

D Have the installation regularly checked and maintained.

D Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

D Electromagnetic energy can interfere with

sensitive electronic equipment such as

computers and computer-driven equipment

such as robots.

D Be sure all equipment in the welding area is

electromagnetically compatible.

D To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

D Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

D Be sure this welding machine is installed and grounded

according to this manual.

D If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

1-4. California Proposition 65 Warnings

Y Welding or cutting equipment produces fumes or gases which

contain chemicals known to the State of California to cause

birth defects and, in some cases, cancer. (California Health &

Safety Code Section 25249.5 et seq.)

Y Battery posts, terminals and related accessories contain lead

and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

For Gasoline Engines:

Y Engine exhaust contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive

harm.

For Diesel Engines:

Y Diesel engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects, and

other reproductive harm.

OM-227 675 Page 4

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from Global Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, American Welding Society Standard

AWS F4.1 from Global Engineering Documents (phone:

1-877-413-5184, website: www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA

02269−9101 (phone: 617−770−3000, website: www.nfpa.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 1735 Jefferson Davis Highway,

Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, web-

site: www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, from

Canadian Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone:

800−463−6727 or in Toronto 416−747−4044, website: www.csa−in-

ternational.org).

Practice For Occupational And Educational Eye And Face Protection,

ANSI Standard Z87.1, from American National Standards Institute, 11

West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900,

website: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone:

617−770−3000, website: www.nfpa.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there

are 10 Regional Offices−−phone for Region 5, Chicago, is

312−353−2220, website: www.osha.gov).

1-6. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro-

magnetic fields. There has been and still is some concern about such

fields. However, after examining more than 500 studies spanning 17

years of research, a special blue ribbon committee of the National

Research Council concluded that: “The body of evidence, in the

committee’s judgment, has not demonstrated that exposure to power-

frequency electric and magnetic fields is a human-health hazard.”

However, studies are still going forth and evidence continues to be

examined. Until the final conclusions of the research are reached, you

may wish to minimize your exposure to electromagnetic fields when

welding or cutting.

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from opera-

tor as practical.

5. Connect work clamp to workpiece as close to the weld as possi-

ble.

About Pacemakers:

Pacemaker wearers consult your doctor before welding or going near

welding operations. If cleared by your doctor, then following the above

procedures is recommended.

OM-227 675 Page 5

SECTION 2 − DEFINITIONS

A. Warning! Watch Out! There

are possible hazards as

shown by the symbols.

B. Drive rolls can injure fingers.

C. Welding wire and drive parts

are at welding voltage during

operation − keep hands and

metal objects clear.

1 Electric shock can kill.

1.1 Wear dry insulating gloves.

Do not touch electrode with

bare hand. Do not wear wet or

damaged gloves.

1.2 Protect yourself from electric

shock by insulating yourself

from work and ground.

1.3 Disconnect input plug or

power before working on

machine.

2 Breathing welding fumes can

be hazardous to your health.

2.1 Keep your head out of the

fumes.

2.2 Use forced ventilation or local

exhaust to remove the fumes.

2.3 Use ventilating fan to remove

fumes.

3 Welding sparks can cause

explosion or fire.

3.1 Keep flammables away from

welding. Don’t weld near

flammables.

3.2 Welding sparks can cause

fires. Have a fire extinguisher

nearby and have a watch

person ready to use it.

3.3 Do not weld on drums or any

closed containers.

4 Arc rays can burn eyes and

injure skin.

4.1 Wear hat and safety glasses.

Use ear protection and button

shirt collar. Use welding

helmet with correct shade of

filter. Wear complete body

protection.

5 Become trained and read the

instructions before working on

the machine or welding.

6 Do not remove or paint over

(cover) the label.

2-1. Warning Label Definitions

OM-227 675 Page 6

2-2. Symbols And Definitions

Amperes

Volts Alternating Current

Duty Cycle

Degree Of

Protection

Hertz Time Wire Feed

Jog Output Trigger Line Connection

Set Up Sequence Trigger Hold On Trigger Hold Off

Purge Press To Set Start Crater

Primary Voltage Preflow Time Postflow Time Read Instructions

Increase

Primary Current

Rated Current

Load Voltage

Notes

Work like a Pro!

Pros weld and cut

safely. Read the

safety rules at

the beginning

of this manual.

OM-227 675 Page 7

SECTION 3 − INSTALLATION

3-1. Specifications

Welding Power

Source Type

Type of Input

Power

Wire Feed

Speed Range

Wire

Diameter

Range

Welding Circuit

Rating

Overall

Dimensions

Weight

Deltaship

Constant Voltage

(CV) DC With

6-Pin Receptacle

24 Volts DC

(5 Amp) For Wire

Feed Motor

24 Volts DC

(0.5 Amp) For Gas

Valve

0 to 780 ipm

(0 To 20 mpm)

Solid Wire .045

To 1/16 in

(1.2 To 1.6 mm)

Flux Cored Wire

.045 To .068 in

(1.2 To 1.7 mm)

Max Spool

Weight:

44 lb (20 kg)

45 Volts,

500 Amperes,

60% Duty Cycle

Length: 20 in

(508 mm)

Width: 9 in

(229 mm)

Height: 13-3/4 in

(286 mm)

21.3 lb

(9.7 kg)

804 451

Y Do not put feeder where

welding wire hits cylinder.

Y Do not move or operate

equipment when it could tip.

1 Wire Feeder

2 Wire Spool/Reel

3 Gas Cylinder w/Hose And

Regulator (Customer

Supplied)

. Shielding gas pressure must

not exceed 90 psi (620 kPa).

4 Welding Power Source

3-2. Site Selection

Wire feeder shown is representative

only and does not reflect actual unit.

OM-227 675 Page 8

3-3. Equipment Connection Diagrams

1 Deltaship 502 Welding Power

Source With 24 VDC Power

2 6-Pin Control Cord

3 Positive Weld Cable

(Customer Supplied)

4 Work Cable (Customer

Supplied)

5 Work

6 DS-2 Wire Feeder

7 Welding Gun

8 Gas Hose (Customer

Supplied)

3-4. Installing Wire Guides And Drive Rolls

804 454

1 Pressure Assembly Knob

2 Pressure Assembly Arm

Move knob to the right to release

pressure arm.

3 Inlet Wire Guide

4 Inlet Wire Guide Securing

Knob

To change inlet wire guide, loosen

knob and remove guide.

5 Drive Roll

6 Drive Roll Securing Nut

The drive roll consists of two differ-

ent sized grooves. The stamped

markings on the end surface of the

drive roll refers to the groove on the

opposite side of the drive roll. The

groove closest to the motor shaft is

the proper groove to thread.

To change drive roll, turn securing

nut one click. Replace drive roll.

Turn securing nut one click.

Tools Needed:

1.2 mm

Corresponding

1.2 mm Wire

Groove

1.2 mm Wire

Size Stamp

OM-227 675 Page 9

3-5. 6-Pin Plug PLG8 Information

Pin Pin Information

1 Motor voltage; 0 to +21 volts dc with motor M1 running.

2 Gas valve voltage; +24 volts dc when gun is triggered or when purging gas.

3 Trigger/Jog; Normally +15 volts dc; 0 volts dc when gun is triggered and + 7 volts dc when Jog

switch PB1 is pressed.

4 Voltage and wire feed speed; −2 to +3 volts dc output command for voltage and wire speed.

5 Remote circuit common.

6 Negative (common) for motor M1 and gas valve GS1.

3-6. 5-Pin Plug PLG1 Information

Pin Pin Information

1 Pin 3 of plug PLG8 and pin 1 of gun trigger (RC2-1)

2 Pin 4 of plug PLG8

3 Pin 5 of plug PLG8

4 Pin 2 of gun trigger (RC2-2)

197 504

5 Not used.

OM-227 675 Page 10

1 Gas Hose (Customer

Supplied)

Connect to gas supply.

2 6-Pin Plug PLG8

Use plug to make connection to

welding power source.

3 Weld Cable w/Quick Connect

(Dinse)

3-7. Connecting 6-Pin Plug And Shielding Gas

Tools Needed:

11/16 in

804 450 / 804 477

OM-227 675 Page 11

1 Female Weld Cable Connec-

tor (Supplied)

2 Weld Cable (Customer Sup-

plied)

Select weld cable according to

welding power source Owner’s

manual.

Install female weld cable connector

as shown.

3 Male Weld Cable Connector

Connect male and female weld

cable connectors.

3-8. Connecting Weld Cable

804 477

A. Push weld cable through insulator as shown.

B. Remove 1 in. (25 mm) of insulation from end of cable.

C. Install supplied sleeve on stripped end of cable.

D. Insert cable with sleeve into connector body so that cable is

snug and against bottom of connector body.

E. Install and tighten setscrew with supplied hex wrench to se-

cure connector body onto cable.

F. Push insulator onto connector body to cover setscrew.

Insulator

Weld CableSleeve

Setscrew

Connector Body

(Male Or Female)

OM-227 675 Page 12

1 Gun Securing Knob

2 Gun Block

3 Gun End

Loosen knob and insert gun into

block. Position wire outlet guide as

close as possible to drive rolls with-

out touching. Tighten knob.

4 Gun Trigger Plug

Connect gun trigger plug to match-

ing receptacle on wire feeder.

3-9. Connecting Welding Gun

804 452

Notes

Work like a Pro!

Pros weld and cut

safely. Read the

safety rules at

the beginning

of this manual.

OM-227 675 Page 13

3-10. Installing Wire Spool And Adjusting Hub Tension

804 450 / Ref. ST-802 483-A / Ref. ST-072 573-B

When a slight force is needed

to turn spool, tension is set.

15/16 in

Tools Needed:

1 Spool Hub

2 Retaining Ring

3 Hub Pin

Remove retaining ring. Slide wire

spool onto spool hub so wire feeds

off bottom of spool. Install spool so

hub pin fits spool hole. Reinstall re-

taining ring.

4 Tension Nut

Adjust tension nut so a slight force is

needed to turn spool.

OM-227 675 Page 14

3-11. Threading Welding Wire

Tools Needed:

1 Pressure Assembly

2 Pressure Assembly

Adjustment Knob

Lay gun cable out straight.

A Open pressure assembly,

hold wire tightly, and cut off

end. Push wire through guides

into gun.

B Close and tighten pressure

assembly, and let go of wire.

C To adjust drive roll pressure,

press gun trigger to feed wire

against wood surface. Tighten

knob so wire does not slip.

Cut off wire.

804 452

WOOD

Tighten

OM-227 675 Page 15

SECTION 4 − OPERATION

4-1. Pendant Controls

Controls are pendant mounted. An optional re-

mote pendant extension cord is available.

1 Voltage Control

Use control to set welding power source volt-

age at the wire feeder. Numbers are for refer-

ence only.

2 Amperage Control

Use control to adjust amperage from min. to

max.

. Match colored bands on voltage and am-

perage controls to get an acceptable

welding condition.

3 Jog Switch

Use Jog switch to momentarily feed welding

wire at speed set at Amperage control without

energizing welding circuit or shielding gas

valve.

803 450 / 229 240

. The numbers around the controls

are for reference only and do not

represent an actual value.

Notes

Work like a Pro!

Pros weld and cut

safely. Read the

safety rules at

the beginning

of this manual.

OM-227 675 Page 16

SECTION 5 − MAINTENANCE & TROUBLESHOOTING

5-1. Routine Maintenance

Y Disconnect power before maintaining.

3 Months

Replace

Unreadable

Labels

Clean And

Tighten

Weld

Terminals

Repair Or

Replace

Cracked

Weld Cable

10-Pin Cord Gas HoseGun Cable

Replace

Cracked

Parts

6 Months

Blow Out Or Vacuum

Inside,

During Heavy Service,

Clean Monthly

Clean

Drive

Rolls

5-2. Troubleshooting

Trouble Remedy

No weld output; unit completely

inoperative.

Place line disconnect switch in On position (see welding power source owner’s manual).

Check and replace line fuse(s), if necessary, or reset circuit breaker (see welding power source own-

er’s manual).

Check for proper input power connections (see welding power source owner’s manual).

Check for proper jumper link position (see welding power source owner’s manual).

No weld output; Power switch pilot light

on.

Check, repair, or replace feeder (see welding power source owner’s manual).

Unit overheated. Allow unit to cool with fan On (see welding power source owner’s manual).

Check control board PC1 and/or motor drive board PC2.

Unit provides only maximum or

minimum weld output.

Check control board PC1, motor drive board PC2 and Hall Device HD1.

Erratic or improper weld output.

Use proper size and type of weld cable (see welding power source owner’s manual).

Clean and tighten all weld connections.

Check wire feeder installation (see Section 3-3).

Check control board PC1, motor drive board PC2 and/or SCR in main rectifier.

Page is loading ...

Miller DS-2, DS-2 (2006), LG000000 Owner's manual

Other documents