Page is loading ...
Job Name Item #
Location
Engineer Contractor
PO # Tag
Representative
CAST IRON
CLOSET FLANGE
TECHNICAL SPECIFICATION
SPECIFICATIONS
Oatey Cast Iron Closet Flanges are designed for use on plastic or heavy
weight, no hub or service weight soil pipe. Does not require caulking.
Comes complete with body, brass ring, bolts and gasket.
DESCRIPTION
Available with rubber cap.
Oatey Co. | 20600 Emerald Parkway, Cleveland, OH 44135 | P: 1.800.321.9532 | oatey.com
Access BIM/Revit content through www.oatey.com
8/19
DIRECTIONS
For use on the outside of pipe. Place over pipe so that gasket secures to
the pipe. Tighten integrated fasteners to pipe to secure closet flange. Use
fasteners to secure flange to subflooring and add closet bolts to secure
toilet fixture.
CAST IRON CLOSET FLANGE
P
Product Number Description Pack
42253 3" Cast Iron Flange w/o test cap 6
42255 4" Cast Iron Flange w/o test cap 6
42256 4" Cast Iron Flange w/ test cap 6
PRODUCT SELECTOR
PHYSICAL PROPERTIES
Cast Iron Red
DIMENSIONS
3" CAST IRON CLOSET FLANGE DIMENSIONS
[A]: Overall Diameter 6.9" [D]: Overall Height 2.0"
[B]: Screw Center 1 4.5" [E]: Inner Dimension 1 4.2"
[C]: Screw Center 2 6.1" [F]: Inner Dimension 2 3.6"
4" CAST IRON CLOSET FLANGE DIMENSIONS
[A]: Overall Diameter 6.9" [D]: Overall Height 2.0"
[B]: Screw Center 1 5.5" [E]: Inner Dimension 1 5.3"
[C]: Screw Center 2 6.1" [F]: Inner Dimension 2 4.7"
CAST IRON CLOSET FLANGE DIMENSIONS
F
D
E
B
A
C
REVISIONS
ECN
REV.
DESCRIPTION
DATE
APPROVED
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
SHEET 1 OF 1
THIRD ANGLE PROJECTION
DRAWING INTERPRETATION
USING ASME Y14.5M
REV.
CRITICAL DIMENSION
FOR INSPECTION
Cast Iron Flange
ALL DRAWINGS ARE THE PROPERTY OF
WITHOUT OFFICIAL WRITTEN PERMISSION FROM
AND ARE TO BE PROMPTLY RETURNED
UPON REQUEST.
AND SHALL NOT BE REPRODUCED OR DISTRIBUTED
MOLD NO.
N.A.
AS SHOWN
APPROVALS
PART NO.
.XXX
.005
FRACTIONS DECIMALS ANGLES
TOLERANCES ARE:
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
1/4 .XX
.020
1
SHEET 1 OF 1
CHECKED
DRAWN
DATE
TITLE
DO NOT SCALE DRAWING
MATERIAL
B
SIZE
SCALE:1:2
F
D
E
B
A
C
REVISIONS
ECN
REV.
DESCRIPTION
DATE
APPROVED
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
SHEET 1 OF 1
THIRD ANGLE PROJECTION
DRAWING INTERPRETATION
USING ASME Y14.5M
REV.
CRITICAL DIMENSION
FOR INSPECTION
Cast Iron Flange
ALL DRAWINGS ARE THE PROPERTY OF
WITHOUT OFFICIAL WRITTEN PERMISSION FROM
AND ARE TO BE PROMPTLY RETURNED
UPON REQUEST.
AND SHALL NOT BE REPRODUCED OR DISTRIBUTED
MOLD NO.
N.A.
AS SHOWN
APPROVALS
PART NO.
.XXX
.005
FRACTIONS DECIMALS ANGLES
TOLERANCES ARE:
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
1/4 .XX
.020
1
SHEET 1 OF 1
CHECKED
DRAWN
DATE
TITLE
DO NOT SCALE DRAWING
MATERIAL
B
SIZE
SCALE:1:2
/
