Generation Lighting 89102 Operating instructions

Brand
Generation Lighting
Model
89102
Type
Operating instructions

This manual is also suitable for

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-949
FIGURE 1
*NOT INCLUDED
0
72108
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• To reduce the risk of fire, electric shock or personal injury, mount to
outlet box or supporting system able to support the weight of the
fixture.
• Read instructions carefully.
• Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
T
o clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Insert fixture mounting screws (B) in threaded holes of universal
mounting bar (A). Run fixture mounting screws (B) all the way down
to the heads.
Place universal mounting bar (A) against outlet box (not supplied) and
secure in place using outlet box screws (not supplied). Be sure the
fixture mounting screws (B) are perfectly horizontal so fixture hangs
straight.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
STEP 2:
INSTALLATION
NOTE: THIS GLASS IS HANDCRAFTED, THE SLIGHT IMPERFECTIONS IN
THE GLASS ADD TO THE AUTHENTICITY OF THE FIXTURE.
*OUTLET BOX
UNIVERSAL
MOUNTING
BAR (A)
*WIRE CONNECTOR
BACKPLATE (C)
DECORATIVE
CAP NUTS
(E)
*HOUSE
GROUND
WIRE
FIXTURE
GROUND
WIRE (I)
GREEN
GROUNDING
SCREW (H)
*OUTLET
BOX
SCREWS
MOUNTING
SCREWS (B)
NOTE: FOR FIXTURES LABELED FOR WET LOCATION AND
USED OUTDOORS.
CAUTION:
To reduce the risk of electrical shock, provide a watertight
seal between the fixture and the mounting surface by using a silicone
or similar caulking.
WET LOCATION
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
YOUR HANDCRAFTED, SOLID BRASS LIGHTING FIXTURE HAS BEEN
COATED WITH A DURABLE, BAKED ON ACRYLIC LACQUER WHICH
GIVES MAXIMUM PROTECTION AGAINST THE WEATHER. IN TIME,
HOWEVER, THE BRIGHTNESS OF THE BRASS WILL TARNISH GIVING
WAY TO AN AUTHENTIC OLD WORLD BRASS FINISH.
NOTE: TO KEEP YOUR SOLID POLISHED BRASS FIXTURE LOOKING
NEW FOR YEARS TO COME, REGULARLY APPLY A GOOD QUALITY
NON-ABRASIVE CAR WAX TO ALL METAL SURFACES, GIVING THE
FIXTURE AN EXTRA PROTECTIVE COATING.
ROOF
ASSEMBLY
(G)
CAGE (F)
CAP
NUTS
(D)
*PARALLEL WIRE (ROUND & SMOOTH) *PARALLEL WIRE (SQUARE & RIDGED)
B
LACK WHITE
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
Hg
MARK MEANS LAMP CONT
AINS MERCUR
Y
.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
FIGURE 2
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
SELF
BALLASTED
LAMP (J)
SOCKET (K)
GROUNDING INSTRUCTIONS:Connect the supply ground wire,
fixture ground wire using UL approved wire nuts. Gently try to
remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
INSTALLATION (continued) HC-949
STEP 3:
A
.
T
ake note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 4:
A
fter wires are connected, tuck them carefully inside the outlet box.
Position backplate (C) over mounting screws (B) and secure in place
with cap nuts (D).
Make sure no bare wires can be seen outside wire connectors.
I
nstall self ballasted lamp (J) by gently twisting into socket (K).
FINAL ASSEMBLY
STEP 5:
STEP 6:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixtur
e wire from group B to the white wire from the
outlet box in the same manner.
P
lace top roof assembly (G) onto cage (F) and secure with
decorative cap nuts (E).
STEP 7:
  • Page 1 1
  • Page 2 2

Generation Lighting 89102 Operating instructions

Brand
Generation Lighting
Model
89102
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents