Sony CMT-VC1 Operating instructions
- Category
- Cassette players
- Type
- Operating instructions
Micro Hi-Fi
Component
System
© 2001 Sony Corporation
Operating Instructions
4-236-347-13 (1)
CMT-VC1
2
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is classified
as a CLASS 1 LASER
product. The CLASS 1
LASER PRODUCT
MARKING is located on
the rear exterior.
To prevent fire, do not cover the ventilation of the
apparatus with news papers, table-cloths, curtains,
etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Don’t throw a battery, dispose it as
the injurious wastes.
This system can play the
following discs
Disc logo
Contents
Disc size
Play time
Note on VIDEO CDs
This system conforms to VIDEO CDs without PBC
functions (Ver. 1.1) and VIDEO CDs with PBC
functions (Ver. 2.0) of VIDEO CD standards. You
can enjoy two kinds of playback according to the disc
type.
Disc type
VIDEO CDs without
PBC functions
(Ver. 1.1 discs)
VIDEO CDs with
PBC functions
(Ver. 2.0 discs)
* PBC = Play Back Control
VIDEO CDs
Audio + Video
(moving pictures)
12 cm/8 cm
74 min./20 min.
Audio CDs
Audio
12 cm/8 cm
74 min./20 min.
You can
Enjoy video playback
(moving pictures) as well as
audio CDs.
Play interactive software
using menu screens displayed
on the TV screen (menu
playback), in addition to the
video playback function of
VIDEO CDs without PBC
functions.
Moreover, you can play high
or standard quality still
picture.
3
Parts Identification
Main unit ............................................... 4
Remote Control ..................................... 5
Getting Started
Hooking up the system .......................... 6
Inserting two size-AA (R6) batteries into
the remote control ........................... 7
Setting the time...................................... 8
VIDEO CD/CD
Loading the disc .................................... 9
Playing the VIDEO CD
–– Normal Play/Shuffle Play/
Repeat Play ..................................... 9
Playing a VIDEO CD with PBC
functions (Ver. 2.0)
–– PBC Play .................................. 10
Playing the CD
–– Normal Play/Shuffle Play/
Repeat Play ................................... 11
Programming the CD/VIDEO CD tracks
–– Program Play ............................ 11
Using the VIDEO CD/CD display ...... 12
Using the on-screen display ................ 13
Resuming VIDEO CD playback from the
point last stopped at
–– Resume Play............................. 13
Tuner
Presetting radio stations.......................14
Listening to the radio
–– Preset Tuning ........................... 14
Tape
Loading a tape ..................................... 15
Playing a tape ...................................... 15
Recording to a tape
––
CD Synchro Recording/
Recording Manually/Program Edit ...
16
Timer-recording radio programs ......... 17
Sound Adjustment
Adjusting the sound ............................. 18
Other Features
Changing the audio channel ................ 19
Falling asleep to music
— Sleep Timer .............................. 19
Waking up to music
— Daily Timer .............................. 20
Optional Components
Hooking up the optional components... 21
Connecting headphones....................... 21
Additional Information
Precautions .......................................... 22
Troubleshooting................................... 23
Specifications ...................................... 25
Glossary ............................................... 26
Table of Contents
4
Parts Identification
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses () for details.
Main unit
CD cover qa (9, 21)
Shown open in the illustration
above.
CD SYNC 9 (16, 17)
CD u qk (9-13, 19, 26)
CD x qj (9-13, 24)
CD .m/M> qh (10,
11)
CD Z qg (9-11)
DSG indicator qd (19)
FUNCTION 7 (9, 11, 12, 14-16,
19, 21, 24)
PBC indicator qf (10, 26)
PHONES jack qs (21)
Remote sensor q;
TAPE PAUSE X 5 (15-17)
TAPE Y 2 (15-17)
TAPE x 3 (15-17, 24)
TAPE m/M 4 (15)
TUNER/BAND w; (14, 24)
VOLUME 8 (20)
BUTTON DESCRIPTIONS
@/1 (power) 1 (7, 14, 17, 20, 21)
Z 6 (15)
+/– ql (14)
12
5
4
7
63
8
9
q;
qs
qg qdqj qhqk
ql
w;
qa
qf
Parts Identification
5
Remote Control
CD ql (9, 11)
CLOCK/TIMER SELECT 4
(18, 20)
CLOCK/TIMER SET 5 (8, 17,
20)
DIR MODE wj (15-17)
DISPLAY wk (12)
DSG qj (18)
ENTER 8 (8, 14, 17, 20)
MEMORY wl (14)
NEXT qa (10)
Numeric buttons wh (10, 11)
ON SCREEN 7 (13)
PREV wd (10)
REC z 9 (16)
REPEAT qf (10, 11)
RETURN O qs (10)
SLEEP e; (19)
SLOW y wf (9)
STEREO/MONO 6 (14, 19, 24)
TAPE qh (15)
TUNER BAND qk (14)
TUNING MODE/PLAY MODE
w; (9, 11-14, 24)
TV/VIDEO 1 (7)
TV @/1 2 (7)
VOLUME +/– qg (20)
BUTTON DESCRIPTIONS
N ws (9-13, 15, 19, 26)
X wa (9, 11, 15-17)
x qd (9-13, 15-17)
. wd (10-12)
> qa (10-12)
m wg (10, 11, 14, 15)
M 0 (10, 11, 14, 15)
@/1 (power) 3 (7, 14, 17, 20, 21)
+ qa (8, 17, 20)
– wd (8, 17, 20)
`/1
X
O
y
123
4
5
6
7
8
qh
ql
qk
qj
w;
wa
ws
wg
wh
wj
wk
wl
e;
wf
wd
q;
9
qa
qs
qd
qf
qg
6
2 Connect the FM and AM antennas.
Set the AM loop antenna up before
connecting it.
FM75
Ω
A
M
ANTENNA
U
U
Getting Started
Hooking up the system
Follow steps 1 through 6 of the procedure below to hook up your system using the supplied cords
and accessories.
AM loop antenna
Left speaker
Right speaker
FM antenna
1 Connect the speakers.
Connect the right and left speaker cords to
the SPEAKER terminals as shown below.
3
L
#
#
R
3
Insert this portion
Black (#)
Gray (3)
AM loop
antenna
Extend the FM
wire antenna
horizontally
6
2
3
4
1
5
7
Getting Started
3 Connect the VIDEO OUT jack to the
video input jack on your TV with the
supplied video connecting cord.
VIDEO OUT
When using a TV
Turn on your TV and set the input selector to
video input so you can view the pictures from the
system.
4 Set SYSTEM SELECT (color system) to
PAL or NTSC depending on the color
system of your TV.
AUTO
SYSTEM
SELECT
NTSC PAL
The color system
of your TV
AUTO (if your TV
automatically
changes the color
system according
to the input signal)
NTSC
PAL (the factory
setting)
5 For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.
110V-120V
220V-240V
VOLTAGE
SELECTOR
6 Connect the power cord to a wall outlet.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).
To turn on the system, press @/1.
Inserting two size-AA (R6)
batteries into the remote
control
e
E
e
E
Tip
When the remote no longer operates the system,
replace both batteries with new ones.
Note
If you do not use the remote for a long period of time,
remove the batteries to prevent possible damage from
battery leakage and corrosion.
Using the remote
You can operate a Sony TV set.
To
Turn the TV on or off
Switch the TV’s video
input
Set SYSTEM SELECT
to
AUTO.
NTSC.
PAL.
Press
TV @/1.
TV/VIDEO.
8
Setting the time
1 Turn on the system.
2 Press CLOCK/TIMER SET on the
remote.
If you are setting the clock for the first time,
go to step 5.
3 Press +/– on the remote repeatedly
until “SET CLOCK” appears in the
display.
4 Press ENTER on the remote.
The hour indication flashes.
5 Press +/– on the remote repeatedly to
set the hour.
6 Press ENTER on the remote.
The minute indication flashes.
7 Press +/– on the remote repeatedly to
set the minute.
8 Press ENTER on the remote.
The clock will begin operating.
To reset the system clock
Start over from step 1.
9
VIDEO CD/CD
VIDEO CD/CD
Loading the disc
1 Press CD Z.
The CD cover opens and the disc tray slides
out.
2 Load a disc onto the disc tray.
3 Press CD Z again to close the disc
tray.
Tip
You can stand a disc case upright in the groove on top
of the system.
Playing the VIDEO CD
–– Normal Play/Shuffle Play/Repeat
Play
You can play both VIDEO CDs without PBC
functions (Ver. 1.1) and VIDEO CDs with PBC
functions (Ver. 2.0).
You can enjoy two kinds of playback according
to the disc type. The PBC functions of VIDEO
CD (Ver. 2.0) are disabled during Shuffle and
Repeat Play.
1 105
Load with the
label side up.
When you play
a CD/VIDEO
CD single
(8 cm CD/
VIDEO CD),
load it onto the
inner circle of
the tray.
Track number Playing time
1 Turn on your TV and select the video
input.
2 Press FUNCTION repeatedly until “CD”
appears in the display.
The CD u button lights up.
You can switch the function to CD by
pressing the CD button on the remote.
3 Press TUNING MODE/PLAY MODE on
the remote repeatedly until the mode
you want appears in the display.
Select
No display
SHUFFLE
PGM
4 Press CD u (or N on the remote).
Other Operations
To
Stop playback
Pause
Slow playback
To play
The VIDEO CD in original
order.
The tracks on the VIDEO CD in
random order.
The tracks on the VIDEO CD in
any order that you want (see
“Programming the CD/VIDEO
CD tracks” on page 11).
Do this
Press CD x.
Press CD u (or X on the
remote).
*1
Press again to
resume playback.
Press SLOW y on the
remote repeatedly.
The playback speed
changes as follows:
1
/
2
t
1
/
4
t
1
/
8
t
1
/
2
t
......
continued
10
To
Select a track or
scene
*2
Find a point in a track
or scene (Lock Search
Function)
Remove the
VIDEO CD
Play repeatedly
(Repeat Play)
*
1
The video image may be somewhat unstable.
*
2
Except during PBC playback of a VIDEO CD with
PBC functions (Ver. 2.0). See this page for details
on PBC playback.
Playing a VIDEO CD with
PBC functions (Ver. 2.0)
–– PBC Play
You can use menus on your TV screen to enjoy
the disc’s interactive software. The menu
format and structure will differ with each disc.
1 Start playing a VIDEO CD with PBC
functions (Ver. 2.0).
The PBC indicator lights up and a PBC
menu appears on your TV.
The indicator lights up during PBC
playback of a VIDEO CD with PBC
functions (Ver. 2.0). When the PBC
functions are not used (see below), the
indicator goes off.
2 Press the numeric button(s) on the
remote to select the number that you
want from the menu.
3 Follow the menu instructions to enjoy
interactive playback.
To
Stop playback
Go to the next scene or
track
Go back to the
preceding scene or
track
Go back to a previous
menu
Cancel PBC Playback
of a VIDEO CD with
PBC functions
(Ver. 2.0)
Do this
Press CD x.
Press NEXT on the remote.
Press PREV on the remote.
Press RETURN O on the
remote.
• Before you start playing,
select the track you want
using ./> on the
remote, then press
CD u (or N on the
remote).
• Before you start playing,
select the track number
using the numeric buttons
on the remote.
The PBC indicator goes off
and playback begins from
the selected track. Still
images, such as the menu
screens, will not be shown.
Playing the VIDEO CD (continued)
Do this
Press ./> on the
remote repeatedly until you
find the desired track or
scene.
During playback, press and
hold down CD .m/
M> until the system
starts searching.
1Press once to start
searching.
2Press again to increase the
search speed. Each time
you press the button, the
search speed changes as
follows:
1 (slow) t 2 (normal)
t 3 (high) t 1 (slow)
t ...
3Press CD u (or N on
the remote) to stop
searching at the desired
point.
Press CD Z.
Press REPEAT on the
remote repeatedly during
playback until “REPEAT” or
“REPEAT 1” appears in the
display.
REPEAT: For all the tracks
on the VIDEO CD.
REPEAT 1: For only the
currently playing track.
To cancel playing
repeatedly, press REPEAT
on the remote repeatedly
until “REPEAT” and
“REPEAT 1” disappear from
the display.
11
VIDEO CD/CD
Tip
When appears on the TV screen, you have
pressed an invalid button.
To enter numbers over 10
(on the remote only)
1 Press >10.
2 Enter the corresponding digits.
To enter 0, press 10/0 instead.
Example:
To enter number 30, press >10, then press 3 and 10/0.
Playing the CD
–– Normal Play/Shuffle Play/Repeat
Play
This system lets you play CDs in different play
modes.
1 005
1 Press FUNCTION repeatedly until “CD”
appears in the display.
The CD u button lights up.
You can switch the function to CD by
pressing the CD button on the remote.
2 Press TUNING MODE/PLAY MODE on
the remote repeatedly until the mode
you want appears in the display.
Select
No display
SHUFFLE
PGM
3 Press CD u (or N on the remote).
Other Operations
To
Stop playback
Pause
Select a track
Find a point in a track
(Lock Search
Function)
Remove the CD
Play repeatedly
(Repeat Play)
Programming the CD/
VIDEO CD tracks
–– Program Play
You can make a program of up to 20 tracks on
a CD/VIDEO CD in any order that you want.
The PBC functions of VIDEO CD (Ver. 2.0)
are disabled during Program play.
Track number Playing time
To play
The CD in original order.
The tracks on the CD in random
order.
The tracks on the CD in any
order that you want (see
“Programming the CD/VIDEO
CD tracks” on this page).
Do this
Press CD x.
Press CD u (or X on the
remote). Press again to
resume playback.
During playback or pause,
press ./> on the
remote repeatedly until you
find the desired track.
During playback, press and
hold down CD .m/
M> until the system
starts searching. Press
CD u (or N on the
remote) to stop searching at
the desired point.
Press CD Z.
Press REPEAT on the
remote repeatedly during
playback until “REPEAT”
or “REPEAT 1” appears in
the display.
REPEAT: For all the tracks
on the CD.
REPEAT 1: For only the
currently playing track.
To cancel playing
repeatedly, press REPEAT
on the remote repeatedly
until “REPEAT” and
“REPEAT 1” disappear
from the display.
continued
12
1 Press FUNCTION repeatedly until “CD”
appears in the display.
2 Press TUNING MODE/PLAY MODE on
the remote repeatedly until “PGM”
appears in the display.
3 Press ./> on the remote
repeatedly until the desired track
number appears in the display.
3 243
PGM
4 Press TUNING MODE/PLAY MODE on
the remote .
The selected track is programmed.
The selection number appears in the
display.
5 To program additional tracks, repeat
steps 3 and 4.
6 Press CD u (or N on the remote).
To
Cancel Program Play
Add a track to the end
of the program
Erase the entire
program
Tips
• The program you made remains after Program Play
finishes. To play the program again, switch the
function to CD, and then press CD u (or N on
the remote).
• “--.--” appears in the display when the total program
time exceeds 100 minutes.
Using the VIDEO CD/CD
display
Press DISPLAY on the remote repeatedly.
The display changes as follows:
During normal playback
Current track number and elapsed playing time
of the track t Current track number and
remaining playing time of the track t
Remaining playing time of the entire CD/
VIDEO CD t Clock display t Current track
number and elapsed playing time of the track
t ......
(VIDEO CD with PBC functions (Ver. 2.0))
Elapsed playing time of the current track* y
Clock display
* This may not appear when displaying still images,
etc.
While the VIDEO CD/CD is stopped
Total number of tracks and total playing time
t Clock display t Current source display t
Total number of tracks and total playing time
t ......
Note
If the CD/VIDEO CD contains 21 tracks or more, the
remaining playing time of the current track will
appears as “--.--” for each track starting with the 21st.
Selected track
number
Total playing time
Do this
Press TUNING MODE/
PLAY MODE on the remote
repeatedly until “PGM”
disappears from the display.
Do steps 3 and 4 with
Program Play stopped.
Press CD x with Program
Play stopped.
Programming the CD/VIDEO CD
tracks (continued)
13
VIDEO CD/CD
Using the on-screen
display
You can check the current operating status and
disc information for VIDEO CDs and audio
CDs while the VIDEO CD/CD is playing or
stopped.
Press ON SCREEN on the remote.
The on-screen display changes as follows:
ON SCREEN ON y ON SCREEN OFF
ON SCREEN ON display
9 29:48 VCD STOP
CONTINUE RESUME
1 2 3 4 5
6 7 8 9
PBC OFF
REPEAT
2
1
7
4
3
6
5
1
When
The VIDEO CD/CD is
stopped
The VIDEO CD/CD is
playing
2 Play mode*
* In Program Play, the selection number and
programmed track number appears below.
3 “PBC ON,”* “PBC OFF” or no display
* “PBC ON” is displayed for a VIDEO CD with PBC
functions.
4 “REPEAT,” “REPEAT 1” or no display
5
When
The VIDEO CD/CD is
stopped
The VIDEO CD/CD is
playing
6 “RESUME” or no display
7 Music calendar* or no display
* Track numbers disappear from the music calendar
after they are played.
When the PBC functions are not used, the music
calender appears only while the VIDEO CD is
stopped.
Tip
Depending on the condition, some items are
displayed, while others are not.
Resuming VIDEO CD
playback from the point
last stopped at
–– Resume Play
This function cannot be used with an audio CD.
1 While playing a VIDEO CD, press CD x
to stop playback.
“RESUME” appears on your TV screen. If
“RESUME” does not appear, Resume Play
is not available.
2 Press CD u (or N on the remote).
To view from the beginning of the
VIDEO CD
When “RESUME” appears in the display, press
CD x, then press CD u (or N on the
remote).
Notes
• Resume Play is not available in Shuffle or Program
Play, or during PBC playback of a VIDEO CD with
PBC functions (Ver. 2.0).
• Depending on where you stopped the VIDEO CD,
the system may resume playback from a different
point.
• Resume Play is cancelled when:
—you press a numeric button or TUNING MODE/
PLAY MODE on the remote, or CD x.
—you remove the VIDEO CD.
—you disconnect the power cord.
—you turn off the system.
The display shows
Total number of tracks and
total playing time of disc
Current track number and
elapsed playing time of the
track
The display shows
STOP
PLAY
14
Tuner
Presetting radio stations
The system can store a total of 30 preset
stations (20 for FM and 10 for AM).
1 Press FUNCTION repeatedly until
“TUNER” appears in the display.
The TUNER/BAND button lights up.
2 Press TUNER/BAND to select FM or
AM.
3 Press TUNING MODE/PLAY MODE on
the remote repeatedly until “AUTO”
appears in the display.
4 Press +/– (or m/M on the remote).
The frequency changes as the system scans
for a station. Scanning stops automatically
when a station is tuned in. At that time,
“TUNED” and “STEREO” (for stereo
program only) appear.
5 Press MEMORY on the remote.
A preset number flashes.
1FM1005
STEREO
TUNED
M
H
z
PRESET
6 Press +/– on the remote repeatedly to
select the preset number that you want.
7 Press ENTER on the remote.
The station is stored to the selected preset
number.
8 Repeat steps 2 through 7 to preset
other stations.
To tune in a weak station
In step 3, press TUNING MODE/PLAY
MODE on the remote repeatedly until
“AUTO” and “PRESET” disappear from the
display, then press +/– (or m/M on the
remote) repeatedly to tune in the station.
To change the preset number
Start over from step 2.
Preset number
Frequency
Tip
The preset stations are saved in the system’s memory
for about a day even if you disconnect the power cord
or a power failure occurs.
To change the AM tuning interval
The AM tuning interval is factory-preset to 9 kHz.
To switch the AM tuning interval, tune in any AM
station first, then turn off the system. Pressing and
holding down +, turn the system back on. When you
change the interval, all the AM preset stations are
erased. To change back to the original interval, tune
in any AM station first, then turn off the system.
Pressing and holding down –, turn the system back
on.
Listening to the radio
–– Preset Tuning
Presetting radio stations in the system’s
memory in advance make it easy to tune in
those stations later (see “Presetting radio
stations” on this page).
1 Press FUNCTION repeatedly until
“TUNER” appears in the display.
2 Press TUNER/BAND to select FM or
AM.
3 Press TUNING MODE/PLAY MODE on
the remote repeatedly until “PRESET”
appears in the display.
4 Press +/– (or m/M on the remote)
repeatedly to display the preset number
of the desired station.
To turn off the radio
Press ?/1.
To tune in a non-preset radio station
In step 3, press TUNING MODE/PLAY
MODE on the remote repeatedly until “AUTO”
and “PRESET” disappear from the display,
then press +/– (or m/M on the remote)
repeatedly to tune in the desired station
(Manual Tuning).
Tips
• If there is static during an FM broadcast, press
STEREO/MONO on the remote until “MONO”
appears in the display. After “MONO” scrolls
across the display, the frequency will appear. The
broadcast will no longer be in stereo, but the
reception will improve.
• To improve the reception, adjust the supplied
antennas or connect an external antenna.
15
Tape
Tape
Loading a tape
1 Press Z.
2 Load a recorded/recordable tape into
the cassette holder.
Playing a tape
You can use Type I (normal) tape.
1 Load a recorded tape into the cassette
holder.
2 Press FUNCTION repeatedly until
“TAPE” appears in the display.
The TAPE Y button lights up.
You can switch the function to TAPE by
pressing the TAPE button on the remote.
3 Press DIR MODE on the remote
repeatedly to select “ ” to play one
side of the tape, “ ” to play both
sides, or “ ”* to play both sides
repeatedly.
* The tape automatically stops after playing back
five times.
4 Press TAPE Y (or N on the remote).
Press TAPE Y (or N on the remote)
again to play the reverse side. The tape
starts playing back.
With the side you want to play/
record on facing towards you
Other Operations
To
Stop playback
Pause
Fast-forward or
rewind
Remove the tape
Do this
Press TAPE x.
Press TAPE PAUSE X (or
X on the remote). Press again
to resume playback.
With the tape stopped, press
TAPE m/M.
Press Z.
Tuner/Tape
16
Recording from a CD/VIDEO CD
(CD Synchro Recording)
Recording manually
Load a recordable tape into the cassette holder.
Load a disc onto the disc tray.
Load a disc or tune in the desired
station.
Press FUNCTION repeatedly until “CD”
appears in the display.
Press FUNCTION repeatedly to select
the source you want to record from.
Press CD SYNC.
Press REC z on the remote.
The tape stands by for recording.
“
” and “B” (or “b”) appear.
To start recording on the side facing away from you, press TAPE Y until “ ”
changes to “ .”
Press DIR MODE on the remote repeatedly to select “ ” to record on one side of
the tape, or “ ” or “ ” to record on both sides.
Press TAPE PAUSE X (or X on the
remote).
Steps
2
3
4
5
6
Recording to a tape
–– CD Synchro Recording/Recording Manually/Program Edit
You can record from a CD/VIDEO CD, radio or any of the connected components. You can use
Type I (normal) tape.
1
Press TAPE PAUSE X (or X on the
remote), and then start playing the
desired source.
To stop recording
Press TAPE x.
Tip
For recording manually:
To pause recording, press TAPE PAUSE X (or X on
the remote).
17
Tape
Recording CD/VIDEO CD
tracks in your favorite order
–– Program Edit
The PBC functions of VIDEO CD (Ver. 2.0)
are disabled during Program Edit.
1 Load a recordable tape into the
cassette holder.
2 Load a disc onto the disc tray.
3 Do steps 1 through 5 in Program Play
(see page 11).
4 Press CD SYNC.
The tape stands by for recording and the
VIDEO CD/CD stands by for playback.
“
” and “B” (or “b”) appear, and the
CD SYNC button lights up.
To start recording on the side facing away
from you, press TAPE Y until “
”
changes to “ .”
5 Press DIR MODE on the remote
repeatedly to select “ ” to record on
one side of the tape, or “ ” or “ ”
to record on both sides.
6 Press TAPE PAUSE X (or X on the
remote).
To
Stop recording
Cancel Program
Edit
Do this
Press TAPE x.
Press TUNING MODE/PLAY
MODE on the remote
repeatedly until “PGM”
disappears from the display.
Timer-recording radio
programs
To timer-record, make sure that you have set
the system clock correctly (see “Setting the
time” on page 8) and preset the radio station
(see “Presetting radio stations” on page 14).
1 Tune in the desired preset radio station
(see “Listening to the radio” on page
14).
2 Load a recordable tape.
3 Press CLOCK/TIMER SET on the
remote.
4 Press +/– on the remote repeatedly
until “SET REC” appears in the display.
“SET REC” scrolls and “c REC” appears
in the display.
5 Press ENTER on the remote.
“ON TIME” appears, then the hour
indication flashes.
6 Set the starting time.
Press +/– on the remote repeatedly to set the
hour, then press ENTER on the remote.
The minute indication begins flashing next.
Press +/– on the remote repeatedly to set the
minute, then press ENTER on the remote.
“OFF TIME” appears, then the hour
indication flashes again.
7 Set the stopping time by repeating step
6.
The start time, the stopping time,
“TUNER,” and the preset station appear in
turn, then the original display returns.
8 Press @/1 to turn off the system.
When the recording starts, the volume level
is automatically set to the minimum.
continued
18
To
Check the settings
Turn off the timer
Tip
Once you set the timer, the time settings will remain
in the system’s memory until you change them, even
when you turn the system or the timer off. The
settings that were last used will be in effect when you
turn the timer on again.
Notes
• The system will turn on 15 seconds before the
specified starting time.
• If the system is turned on at the specified starting
time, recording will not occur.
• When you have set the Sleep Timer, the timer
recording will not operate until the Sleep Timer
Function is turned off.
Do this
Press CLOCK/TIMER
SELECT on the remote
repeatedly until “c REC”
appears in the display. The
preset items appear in turn.
Press CLOCK/TIMER
SELECT on the remote
repeatedly until “c REC”
disappears from the display.
Timer-recording radio programs
(continued)
Sound Adjustment
Adjusting the sound
Generating a more dynamic sound
(Dynamic Sound Generator)
Press DSG on the remote.
To cancel the DSG, press DSG on the remote
again.
19
Other Features
Falling asleep to music
— Sleep Timer
The Sleep Timer Function lets you specify a
sleep time, after which the system stops playing
and turns off automatically. You can thus fall
asleep to music.
Press SLEEP on the remote repeatedly.
The sleep time changes as follows:
AUTO* t 90MIN t 80MIN t 70MIN t
… t 10MIN t OFF t AUTO* t …
* The system turns off after the current CD/VIDEO
CD or tape finishes playing (up to 100 minutes).
The system also turns off when you manually stop
the VIDEO CD/CD or tape.
To
Check the remaining
sleep time
Change the sleep time
Cancel the Sleep
Timer Function
Sound Adjustment/Other Features
Press
SLEEP on the remote once.
SLEEP on the remote
repeatedly until the time
you want appears.
SLEEP on the remote
repeatedly until “OFF”
appears.
Other Features
Changing the audio
channel
1 Press FUNCTION repeatedly until “CD”
appears in the display.
2 Press CD u (or N on the remote).
3 Press STEREO/MONO on the remote
repeatedly to obtain the channel you
want.
The display changes as follows:
MPX R t MPX L t STEREO t MPX R...
20
Waking up to music
— Daily Timer
By setting the Daily Timer, you can make the
system automatically turn on and off at
specified times. To use this function, make
sure that you have set the system clock
correctly (see “Setting the time” on page 8).
1 Prepare the music source you want to
listen to when the system turns on.
• CD/VIDEO CD: Load a disc.
• Tape: Load a tape with the side you want
to play facing towards you.
• Radio: Tune in the preset radio station
that you want (see “Listening to the radio”
on page 14).
2 Adjust the volume.
3 Press CLOCK/TIMER SET on the
remote.
4 Press +/– on the remote repeatedly
until “SET DAILY” appears in the
display.
“SET DAILY” scrolls and “c DAILY”
appears in the display.
5 Press ENTER on the remote.
“ON TIME” appears, then the hour
indication flashes.
6 Set the starting time.
Press +/– on the remote repeatedly to set the
hour, then press ENTER on the remote.
The minute indication begins flashing next.
Press +/– on the remote repeatedly to set the
minute, then press ENTER on the remote.
“OFF TIME” appears, then the hour
indication flashes again.
7 Set the stopping time by repeating step
6.
8 Press +/– on the remote repeatedly
until the music source you want
appears.
The display changes as follows:
t TUNER y CD T
t TAPE T
9 Press ENTER on the remote.
The starting time, the stopping time, and the
music source appear in turn, then the
original display returns.
10
Press @/1 to turn off the system.
To
Check the settings
Turn off the timer
Tip
Once you set the timer, the time settings will remain
in the system’s memory until you change them, even
when you turn the system or the timer off. The
settings that were last used will be in effect when you
turn the timer on again.
Notes
• The system will turn on 15 seconds before the
specified starting time.
• When you have set the Sleep Timer, the Daily
Timer will not operate until the Sleep Timer
Function is turned off.
Do this
Press CLOCK/TIMER
SELECT on the remote
repeatedly until “c DAILY”
appears in the display. The
preset items appear in turn.
Press CLOCK/TIMER
SELECT on the remote
repeatedly until “c DAILY”
disappears from the display.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Sony CMT-VC1 Operating instructions
- Category
- Cassette players
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sony CMT-VP11 User manual
-
-
-
-
-
-
-
-
-