Vivo STAND-SK01 User manual

Brand: Vivo

Model: STAND-SK01

Type: User manual

Vivo STAND-SK01 is a safety kit designed to prevent TVs from tipping over and causing accidents. It comes with all the necessary hardware, including cable straps, wire hooks, clips, and screws, to secure your TV to a table or wall. The kit is easy to install and can be used with TVs of various sizes and designs. You can choose from three different installation options: attaching the kit to the edge of a table, drilling holes into a concrete or brick wall, or using the included anchors to attach the kit to drywall.

    

Instruction Manual

Email: [email protected]

Live chat: www.vivo-us.com

Call: 1-800-371-5654

-  

 

phillips screwdriver

   

Scan the QR code with your mobile device or follow the link

to helpful videos and specifications related to this product.

- -!""## $%""  

 (x1)

Wire

& (x2)

Wire Hook

 (x2)

Clip

 (x2)

Plate

-  (x2)

M5x12

-   (x2)

M5x20

-  (x2)

M4x12

-  & (x2)

M4x20

- ' (x2)

M8x20

-  ( (x2)

M8x40

- ) (x2)

M6x12

-  * (x2)

M6x20

-  + (x2)

Washer

-,  (x4)

Flathea Screw

-,  (x4)

Lon" Screw

- , & (x4)

Anchor

-  - (x1)

Allen Wrench

% 

 

Fasten Wire Hooks (B) to TV using Washers (M-I) and Bolts (M-A -

M-H). The required size of the bolt will depend on the design of

your TV.

. 

Attach Clips (C) to edge of table top, use a screwdriver to secure

them.

 /

 / 0  1

. &

Run Wire (A) through Wire Hooks (B) and holes of Clips (C). Use Allen

Wrench (M-J) to secure the wire into the Clips.

 / 0  1

. /

Attach Plates (D) to edge of table using Flathead Screws (W-A).

 / 0  1

. 2

If placing TV in front of concrete or brick wall, mark drill locations in

wall using Plates (D) as a reference. Drill 1.6" (40mm) deep holes

using a 9/32" (7mm) drill bit and press Concrete Anchors (W-B) into

holes. Attach Plates to wall using Long Screws (W-A).

 / 0  1

. /&

Run Wire (A) through Wire Hooks (B) and holes of Plates (D). Use Allen

Wrench (M-J) to secure the wire into the Plates.

If you do not understand these directions, or if you have any

doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no

missing or defective parts. Improper installation may cause

damage or serious injury. Do not use this product for any

purpose that is not explicitly specified in this manual. We

cannot be liable for damage or injury caused by incorrect

assembly or inappropriate use.

Email: help@vivo-us.com

Live chat: www.vivo-us.com

Call: 1-800-371-5654

For more VIVO products, check out our

website at

www.vivo-us.com.

If any parts are received damaged or defective, please contact

us. We are happy to replace parts to ensure you have a fully

functioning product.

 ,  

   

Last updated: 05/22/18

 / 0  1

. 2&

Run Wire (A) through Wire Hooks (B) and holes of Plates (D) on the

wall. Use Allen Wrench (M-J) to secure the wire into the Plates.

Vivo STAND-SK01 User manual

Vivo STAND-SK01 User manual

Vivo STAND-SK01 User manual

Related papers

Other documents