S
S
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
S
S
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
S
S
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
S
S
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
Overall Rail length is 78⁄”.
2
A
C
G
D
B
F
E
The gap between each pre-drilled hole is 16”.
Door height is H.
The height of holes on the wall is H+1⁄”.
Distance from the bottom of the door to the oor is ⁄”.
End of the rail is 8⁄” away from the entrance of the door.
Distance from door top side to holes on the wall is 1⁄”.
1
1.1,
2.1,
3.1,
3.2,
3.3,
4.1,
4.2,
4.3,
4.4,
Product Content
Tools Needed
2 x Rail
5 x Carriage Bolt and Anchor
5 x Lag Bolt
5 x Wall Spacer
4 x Long Door Screw2 x Hanger
2 x Rubber End
1 x Floor Guide
2 x Door Stopper
1 x Hex Key
2.2,
⁄”
⁄”
A B C D E
Do not screw it in
place at this stage
Joint two rails together. Then install the rail onto
the wall. Adjust the screws to make sure the two
rails are in a horizontal line.
4
3
1,
2,
Pencil
Phillips Screwdriver
Drill
Wrench3,
4,
5,
Plumb Bob
Level
6,
Tape7,
1”
H+1⁄”
Use router or circular saw to create a kerf at bottom
of the door, along the center to allow the tip of the
T-shaped oor guide to t in between, to keep your
door stable and prevent the door bottom swinging
back and forth when you slide it open and closed.
Insert door stoppers into rail. Install door stoppers
between A-B and D-E. Door stopper is used to
prevent the hangers coming out of the rail.
78⁄”
A
8⁄”
D
16” 16” 16” 16”
B
1⁄”
H
H+1⁄”
C
G
F
⁄”
E
2”
3⁄”
16”
16”
16”
16”
Measurements
(For concrete wall)
(For wood stud)
9,
Drill Bit
8,
Drill Bit
For wood stud
Install the lag bolt to
wood stud directly.
For concrete wall
Install the anchor to holes
on the concrete wall rst,
then install carriage bolt
to anchor.
Use a pencil to mark the holes on the wall.
The height of holes on the wall should be H+1⁄”.
The space between each hole is 16”.
If you install the rail onto wood stud, no need to drill
holes in this step.
If you install rail onto concrete wall. Drill the holes on
the wall where the pencil mark is. Make sure the
holes are horizontal.
For concrete wall:
No need to drill holes in this step.
Drill holes in this step.
For wood stud:
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
TM
S
S
mart
tandard
6
7
Install the hangers onto the door according to
the measurement in the pictures below.
Maximum door thickness is 1⁄”. If your door’s
thickness is less than 1⁄”, please add some bolt
washers or cut the long door bolts to a suitable
length to t the door.
Hang the door over the rail
8
Turn the rubber ends approximately 180 degrees so
that they are stuck between the door and the rail.
Adjust the 2 door stoppers to nd a suitable position,
Use the hex key to screw the door stoppers in place.
5
1”
TM
S
S
mart
tandard
Sliding Door Hardware
Manual ( I Shape 6.6ft)
The rubber ends are used to protect the door from
touching the rail when sliding the door. You need
to drill holes on the door top side, please drill the
holes ⁄” away from the edge of the door. Then
install the rubber ends on the door.
Install the oor guidePut oor guide on the oor rst
to x a suitable position and make a mark so that the
tip of the oor guide can work well in the slot.
Use suitable drill bit to drill holes on the oor where the
mark is, and then install the oor guide.
⁄”
2”
3⁄”
9
10
Email: [email protected]
-
1
-
2
SMARTSTANDARD 6.6ft Heavy Duty Sturdy Sliding Barn Door Hardware Kit -Smoothly and Quietly -Easy to install -Includes Step-By-Step Installation Instruction Fit 36"-40" Wide Door Panel (I Shape Hanger) User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
SMARTSTANDARD Sliding Barn Door Hardware User manual
-
SMARTSTANDARD 5 Feet Top Mount Sliding Hardware Kit-Stainless Steel Heavy Duty Sturdy Barn Track-Simple and Easy to Install-Fit 30“ Wide Door Panel (T Shape Hanger) User manual
-
SMARTSTANDARD 6.6 FT Heavy Duty User manual
-
SMARTSTANDARD 5 Feet Heavy Duty Sturdy Sliding Barn Door Hardware Kit-Smoothly and Quietly-Includes Detailed Installation Fit 30" Wide Doorpanel (J Shape Hanger) Black User manual
-
SMARTSTANDARD 8 Feet Heavy Duty Double Sliding Barn Door Hardware Kit -Smoothly and Quietly -Includes Detailed Installation Fit 24" Wide Doorpanel (J Shape Hanger) User manual
-
SMARTSTANDARD 8FT Heavy Duty Sliding Barn User manual
-
SMARTSTANDARD Barn Door Hardware Kit User manual
Other documents
-
Movisa MVT4FXL Operating instructions
-
-
LUBANN LB-Aldr-DR32Z Installation guide
-
Movisa MVTA30Z Installation guide
-
-
-
-
-
Alton VICTORIAN ELLESMERE 8x14+ User manual
-
DreamLine SHEN-6134600-07 Installation guide
