AMX NMX-ACC-N9206 Quick start guide

Brand: AMX

Model: NMX-ACC-N9206

Type: Quick start guide

AMX NMX-ACC-N9206 is a 2RU rack mount cage for rack mounting up to six N-Series Encoder, Decoder, and Audio Transceiver Cards.

With a total power output of 12VDC at up to 15A over all six Phoenix connectors, this device can handle even the most power-hungry cards.

The cage's compact dimensions (3.4” x 17.22” x 5.04”) make it easy to fit into any rack, and its rugged construction ensures that your cards will be safe and secure.

The NMX-ACC-N9206 is easy to install and use, and it comes with all the necessary hardware. It features PoE (Power-over-Ethernet), allowing you to power your cards without having to run additional cables.

AMX NMX-ACC-N9206 is a 2RU rack mount cage for rack mounting up to six N-Series Encoder, Decoder, and Audio Transceiver Cards.

With a total power output of 12VDC at up to 15A over all six Phoenix connectors, this device can handle even the most power-hungry cards.

The cage's compact dimensions (3.4” x 17.22” x 5.04”) make it easy to fit into any rack, and its rugged construction ensures that your cards will be safe and secure.

QUICK START GUIDE

NMX-ACC-N9206 2RU Rackmount Cage with Power

Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

Last Revised: 12/2016

800-9206 REV: A

Overview

The NMX-ACC-N9206 is a 2RU rack mount cage for rack mounting up to six

N-Series Encoder, Decoder, and Audio Transceiver Cards. Cards are powered

by PoE (Power-over-Ethernet) and/or by connecting the card’s 12VDC Input

to the Card Cage’s 12VDC Output using the supplied Phoenix connector

cable.

Calculating Power Requirements

Use either of the following formulas to calculate how much power is required

for the N9206.

Formulas are based on the power requirements of each installed card (e.g.,

Power_Slot1 = the power requirements for whatever card is installed in the

first slot). These formulas add a 20% margin to the power requirements of

the cards to allow for the chassis cooling fan power consumption as well as

any inherent power supply losses.

Total Power = (Power_Slot1 + Power_Slot2 + Power_Slot3 + Power_Slot4 +

Power_Slot5 + Power_Slot6) * 1.2

Total BTU/hr = (BTU/hr_Slot1 + BTU/hr_Slot2 + BTU/hr_Slot3 + BTU/hr_Slot4 +

BTU/hr_Slot5 + BTU/hr_Slot6) * 1.2

Installation Guidelines

To install N-Series cards into the N9206 Card Cage, follow these steps:

1. Gently slide the card into the cage slot. Make sure the card is properly

aligned with the guides. The card’s front LED indicators should align

with the holes in the cage’s faceplate. See FIG. 1.

CAUTION: Cards are static sensitive. Follow all standard ESD precautions

when handling cards. Handle cards by the faceplate and carrier edges only.

Avoiding touching the card components.

2. Align the thumb screw on the back plate before seating the card into

the cage.

3. Firmly seat the card and tighten the thumb screw by hand to secure

card placement.

4. Use one of the six Phoenix connector cables (included in shipment with

the Card Cage) to connect the card’s 12VDC input Phoenix connector

to one of the cage’s six 12VDC outputs.

5. Repeat these steps until all cards are properly installed. See FIG. 2.

FIG. 2 FULLY POPULATED CARD CAGE

6. For proper airflow, cover any unused card slots with faceplate blanks.

Blanks are sold separately (part number NMX-ACC-N9210).

7. Make sure the Card Cage’s power cord is plugged in for proper cooling.

The POWER LED on the front of the cage should always be on.

CAUTION: Keep the Card Cage’s power cord plugged in at all times so that the

internal fans are always running. Failure to do so could void the warranty of

the cage and all installed cards. The card cage cooling fans cannot be

remedy power losses immediately to avoid potential overheating hazards.

NOTE: Mounting accessories are sold separately and are compatible with

most N-Series devices. Contact a sales representative or visit our website at

www.amx.com for details.

Please contact technical support at s[email protected] or

256.461.7143 (x9900) for assistance with any installation issues.

FIG. 1 INSTALLING CARDS

callout

Product Specifications

Model Available: NMX-ACC-N9206

Power

Requirements:

Input: 100-240 Volts @ 1 Amp AC power supply

Output: 12VDC @ up to 15A (total over all six Phoenix

connectors)

Dimensions

(HWD):

3.4” x 17.22” x 5.04” (8.63cm x 43.73cm x 12.8cm)

Weight: 7.61 lbs (3.45 kg)

Certifications: Regulatory compliance: FCC, CE, and NRTL

AMX NMX-ACC-N9206 Quick start guide

Brand: AMX

Model: NMX-ACC-N9206

Type: Quick start guide

AMX NMX-ACC-N9206 is a 2RU rack mount cage for rack mounting up to six N-Series Encoder, Decoder, and Audio Transceiver Cards.

With a total power output of 12VDC at up to 15A over all six Phoenix connectors, this device can handle even the most power-hungry cards.

The cage's compact dimensions (3.4” x 17.22” x 5.04”) make it easy to fit into any rack, and its rugged construction ensures that your cards will be safe and secure.

Download PDF

report

AMX NMX-ACC-N9206 Quick start guide

AMX NMX-ACC-N9206 Quick start guide

Related papers

Other documents