Minka Group 8991-61 User manual

Brand: Minka Group

Model: 8991-61

Type: User manual

This manual is also suitable for

8991-66

Minka Group 8991-61 is suited for use with two 60W E12 bulbs, making it a perfect choice for illuminating larger areas, such as living rooms or dining rooms. It features an attractive design with a black finish and clear glass shade, making it a stylish addition to any home décor. The fixture is easy to install and can be mounted on a wall or ceiling, providing maximum flexibility in placement.

INSTALLATION INSTRUCTIONS

Model # 8991

READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the circuit breaker (avertissement!

couper le courant au niveau des fusibles ou du

disjoncteur)and remove the old fixture including the

mounting hardware.

2. Carefully unpack your new fixture and lay out all the

parts in a clear area. Take care not to misplace any

small parts necessary for installation.

3. Align strap (B) to the outlet box (A) and mark the

location of the wall anchors (I). Insert the wall anchors.

4. Thread nipple (C) into the center of strap (B) and

thread studs (H) into the top of strap (B) spaced the

same distance apart as the holes in the back plate (K).

5. Attach strap (B) to the outlet box (A) using mounting

screws (D) (Part#8/32"*1"L). Screw the wood screws

(G) into the anchor (I) (Fig 1).

CONNECTION THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in Fig.2.Making

sure that all wire connectors are secured. If your outlet

box has a ground wire (green or bare copper), connect

the fixture’s ground wire to it. Otherwise, connect the

fixture’s ground wire directly to the long strap using the

green screw (J) (Part#8/32"*1/3"L) provided.

FINISHING THE INSTALLATION (Fig.1)

7. Align back plate (K) onto nipple (C) and studs (H) and

secure with cap nuts (E,F). (Fig 1)

8. To prevent moisture from entering the outlet box (A)

and causing a short, use clear silicone sealant to

outline the outside of fixture back plate (K) where it

meets the wall leaving a space at bottom to allow

moisture a means to escape. (Fig 3)

9. At this point, unscrew the screws (M&O) and remove

the top cover (N) with the top back plate (L) to install

2X60W/E12 bulbs (no bulb included) in accordance

with the fixture specification—DO NOT EXCEED THE

MAXIMUM WATTAGE RATING! (NOTE: NO BULB

INCLUDED) (NE PAS DEPASSER LA PUISSANCE

NOMINALE MAXIMALE!)

10. If you need to replace the glass shade (P), unscrew

screws (M&O). Remove the top cover (N) with the top

back plate (L). Raise the cluster cover (R). Unplug the

male and female jacket (S) and remove cluster cover

(R). Replace the glass shade (P). Plug the male and

female jacket(S). Replace cluster cover (R). Install

2X60W/E12 bulbs (no bulb included) in accordance

with the fixture specification –DO NOT EXCEED THE

MAXIMUM WATTAGE RATING! (NE PAS DEPASSER

LA PUISSANCE NOMINALE MAXIMALE!)

11. Replace top cover (N) and top back plate (L) and

secure with screws (M&O).

Your installation is now complete. Return power to the

outlet box and test the fixture.

Fig. 1

BARE COPPER(GROUND)

Fig.2

FIXTURE

WIRES

WHITE

BLACK

(HOT)

WIRES

HOUSE

GREEN OR

WHITE

(NEUTRAL)

WIRES

HOUSE

(GROUND)

COPPER

BARE

FIXTURE

WIRES

BLACK

WIRES

FIXTURE

GREEN OR

HOUSE

WIRES

U.S. Patents: D454,654 ; D455,515; D455,856

This product is protected by United States

Federal and/or State Law, including Patent

and/or Copyright laws.

Fig 3

Caulking

Backplate

Minka Group 8991-61 User manual

Brand: Minka Group

Model: 8991-61

Type: User manual

This manual is also suitable for

8991-66

Download PDF

report

Minka Group 8991-61 User manual

This manual is also suitable for

Minka Group 8991-61 User manual

Related papers

Other documents