BDI CORRIDOR-6521-CRL User manual

CORRIDOR-6521-CRL
BDI
Brand
BDI
Model
CORRIDOR-6521-CRL
Type
User manual

This manual is also suitable for

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to
your BDI products. Register today and you will be entered to win
free a BINK table from BDI. www.bdiusa.com/product-registration/
Placement and Maintenance
Corridor
®
Office furniture is designed for indoor use on level floors.
Clean glass with glass cleaner, and steel parts and wood veneer
with a moist cloth.
Your Corridor
®
Office furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Do not use power tools for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at [email protected]. For all other concerns, please
contact your BDI retailer.
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Corridor & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2015, BDI
Made in China. 12.08.2015 V2
C1 Glass Panel
A1 Drawer
Assembly
A2 Left Leg
A3 Right Leg
C12 Removable
side panel x 2
C12 Removable
side panel x 2
A4 Wire Management
Trough
C10 Modesty Panel
C11 Wire Management Lid
C13 Center Drawer
Liner x 1
C14 Side Drawer
Liner x 2
T1 4mm Hex Wrench
H8 1/4-20 x 15mm
Screw x 4
H1 1/4-20 x 12mm
Screw x 3
H5 1/4-20 x 32mm
Screw x 6
H7 Barrel Nut x 4
H10 1/4-20 x 87mm
Screw x 2
H9 1/4-20 x 58mm
Screw x 6
H11 Bumper x 5
H13 Leveler x 4
H12 10-32 x 37mm
Screw x 4
Tool Required:
Phillips screwdriver
bdiusa.com
customerservice@bdiusa.com
CORRIDOR
®
6521
EXECUTIVE DESK
bdiusa.com
customerservice@bdiusa.com
CORRIDOR 6521
EXECUTIVE DESK
2
Step 2 - Install Base
Aligning the Colored Dots on the same side, attach Wire Management Trough A4 to Modesty Panel C8
using Screw H1 and Hex Wrench. Keep screws loose until Step 7.
Colored Dots
C10
A4
H1 (x3)
C10
A4
Step 3 - Match Colored Dot on Right Leg A3 with Colored Dot on Modesty Panel Assembly and attach
using Screws H5 and Hex Wrench T1. Keep screws loose until Step 5. Repeat to attach Left Leg A2 to
Modesty Panel Assembly. Install Glides H13 to the bottom of Legs A2 & A3. With the help of another person,
turn desk upright onto its base.
H13 (x4)
Colored Dot
H5
A3
A2
H5 (x6)
bdiusa.com
customerservice@bdiusa.com
CORRIDOR 6521
EXECUTIVE DESK
3
Step 4 - Insert Barrel Nut H7 into holes of Modesty Panel C10 with the elongated slot sitting horizontally, and
secure with Screw H9 through side of Legs A2 & A3. Keep screws loose until Step 5.
H7
H9
H9
A3
A2
H9
Elongated slot in
Barrel Nut H7 aligns
with Screw H9
H7
H7
H9
H7
H10
Elongated slot in Barrel
Nut H7 aligns with
Screw (P)
H8 (x4)
H7
C10
Step 5 - Secure Drawer Assembly A1 to Leg Assembly using Screw H8 and Hex Wrench T1. Insert Barrel
Nut H7 into holes of Modesty Panel C10 with the elongated slot sitting vertically, and secure with Screw H10
through top of Drawer Assembly A1. Fully tighten all Screws that have been installed in previous steps using
Hex Wrench.
H10
H10
H8
H8
H8
C10
A1
bdiusa.com
customerservice@bdiusa.com
CORRIDOR 6521
EXECUTIVE DESK
4
Step 6 - Insert Bumpers H11 in the center hole and outer holes of Drawer Assembly A1. With the fabric side
facing up, insert Center Drawer Liner C13 into the center drawer and Side Drawer Liners C14 into both side
drawers.
H11 (x5)
C14 (x2)
C13 (x1)
H11
H11
H11
H11
Step 7 - With the help of another person gently lower Glass Panel C1 onto Drawer Assembly A1 and fasten
into place using Screw H9 and Hex Wrench T1. DO NOT OVERTIGHTEN!
H9
H9
H9
H9 (x4)
C1
A1
A1
bdiusa.com
customerservice@bdiusa.com
CORRIDOR 6521
EXECUTIVE DESK
5
Step 8 - Place Wire Management Lid C11 into opening in Glass Panel. Attach Removable Side Panels C12
to Legs A2 & A3 using screws H12 (and a Phillips screwdriver) ensuring the top edge of the Side Panel C12
sits against the top inside edge of Leg A2 & A3.
H12 (x4)
C11
A2
A3
C12
C12
Step 9 - Place AC power strip/surge protector (not included) into Wire Management Trough A4.
A4
A4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

BDI CORRIDOR-6521-CRL User manual

CORRIDOR-6521-CRL
BDI
Brand
BDI
Model
CORRIDOR-6521-CRL
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents