Legrand PLEXO3 Operating instructions

PLEXO3
Legrand
Brand
Legrand
Model
PLEXO3
Type
Operating instructions

Legrand PLEXO3 is a heat reflective panel designed to be installed inside the door cavity to reduce heat transfer and improve energy efficiency. It comes in various sizes to fit different door dimensions and includes support strips for easy installation. The main heat panel should be positioned inside the door with the long strip used for the door length and the short strips for the top and bottom. The support strips have double-sided tape for adhesion and should be placed strategically to ensure a snug fit. After installation, check that the door closes and locks properly.

Legrand PLEXO3 is a heat reflective panel designed to be installed inside the door cavity to reduce heat transfer and improve energy efficiency. It comes in various sizes to fit different door dimensions and includes support strips for easy installation. The main heat panel should be positioned inside the door with the long strip used for the door length and the short strips for the top and bottom. The support strips have double-sided tape for adhesion and should be placed strategically to ensure a snug fit. After installation, check that the door closes and locks properly.

PLEXO3 HEAT REFLECTIVE PANEL
1
Cat.No. A B C
601981-HRP 1 - 2
601982-HRP 1 - 2
601983-HRP 1 1 2
601985-HRP 1 2 -
601986-HRP 1 2 1
601987-HRP 1 1 2
Main Heat Panel Installation
Support Strip Installation
Position the Heat refelective panel inside the door cavity.
Long strip is always meant to be used in the door length, and the shorts
strips to be used top/bottom.
Note: Don’t use the strip on the handle side where crossed out
*- only for 601982-HRP all 3 strips are same size.
Peel the double sided tape
from the support strips.
To install the Heat reflective panel open the door first
(This can be done after the full installation or by removing the door and
applying it seperately)
A
B
(Long)
C
(Short)
NOTE: For 601988 use 2 x 601986-HRP
2
Support Strip Installation
Hold main panel
against the door
i don’t push too hard
Place the stick side face down
Ensure the edge is below
the door lip
Note: Some doors requires 3 strips to be fixed depends on the size.
No strip is required for handle side.
After installing the panel & support strips, make sure the door closes
properly and locks in position.
Press down for good adehsion
PLEXO3 HEAT REFLECTIVE PANEL
1
2
3
3
PLEXO3 HEAT REFLECTIVE PANEL
Dimensions of the Panel/Strip
Warranty
Legrand Australia Pty Ltd will honour all statutory guarantees that you as a
consumer are entitled to rely upon under the Australian and New Zealand
Consumer Laws against a manufacturer, including a guarantee that this product
is of acceptable quality.
To make a claim under any statutory guarantee you should first contact the
supplier, or retailer from whom you purchased this product.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
Legrand Australia
1300 369 777
www.legrand.com.au
ABN: 31 000 102 661
Legrand New Zealand
0800 476 009
www.legrand.co.nz
LE13453AA 01/2022
Paper
C
C
A
A
T
T
:
:
6
6
0
0
1
1
9
9
87-
87-
HRP
HRP
QT
QT
Y
Y
:
:
1
1
QT
QT
Y
Y
:
:
2
2
QT
QT
Y
Y
:
:
2
2
QT
QT
Y
Y
:
:
1
1
QT
QT
Y
Y
:
:
1
1
C
C
A
A
T
T
:
:
6
6
0
0
1
1
9
9
83-
83-
HRP
HRP
C
C
A
A
T
T
:
:
6
6
0
0
1
1
9
9
85-
85-
HRP
HRP
QTY:1QTY:2QTY:1
QT
QT
Y
Y
:
:
2
2
QT
QT
Y
Y
:
:
1
1
QT
QT
Y
Y
:
:
1
1
C
C
A
A
T
T
:
:
6
6
0
0
1
1
9
9
86-
86-
HRP
HRP
C
C
A
A
T
T
:
:
6
6
0
0
1
1
9
9
81-
81-
HRP
HRP
QT
QT
Y
Y
:
:
2
2
C
C
A
A
T
T
:
:
6
6
0
0
1
1
9
9
82-
82-
HRP
HRP
QT
QT
Y
Y
:
:
1
1
QT
QT
Y
Y
:
:
2
2
*
*
C
C
A
A
T
T
:
:
6
6
01
01
9
9
88
88
-
-
HR
HR
P
P
(
(
2
2
s
s
e
e
ts)
ts)
QT
QT
Y
Y
:
:
1
1
234
305.50
455.50
455.60
342.50
234.30
425
150
425
210
305.50 300 210
342
234
210
342
210
300
155.50
155.60
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
  • Page 1 1
  • Page 2 2
  • Page 3 3

Legrand PLEXO3 Operating instructions

PLEXO3
Legrand
Brand
Legrand
Model
PLEXO3
Type
Operating instructions

Legrand PLEXO3 is a heat reflective panel designed to be installed inside the door cavity to reduce heat transfer and improve energy efficiency. It comes in various sizes to fit different door dimensions and includes support strips for easy installation. The main heat panel should be positioned inside the door with the long strip used for the door length and the short strips for the top and bottom. The support strips have double-sided tape for adhesion and should be placed strategically to ensure a snug fit. After installation, check that the door closes and locks properly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents