iO ion8i Access Point User guide

Type
User guide

This manual is also suitable for

QUICK START GUIDE
ion8i
Access Point
ANYWHERE
EVERYWHERE
2. Quick Start Guide
3. AC Power Adaptor
4. Mounting Bracket
Packaging Content
Thank you for choosing ion8i Wireless Access Point with 4x4:4
Multi-User MIMO and 802.11ac Wave 2 compliance.
1. ion8i Wireless Access Point
AC Power Adaptor
(Varies by Region)
ion8i
Access Point
Mounting Bracket
1
Product Overview
Place the Mounting Bracket which came with the package on
a wall or ceiling and mark holes with a marker where you will
insert the screws. Drill holes in the marked points and insert
the plastic wall anchors.
Mounting of ion8i Access Point
LAN + PoE
(Power up the device
by PoE Adaptor and a
regular Ethernet Port)
WAN Combo Port
(Combination of Ethernet and SFP)
DC Jack
(Power up using
12 V Adaptor)
SFP
(Connect fiber cable)
Reset
(To reset the device)
1.
2
Use the supplied screws and attach the mounting bracket to the
wall.
Note: Make sure that the mounting bracket is tightly installed
before mounting the Access Point on the wall or ceiling.
Mounting
Bracket Wall/
Ceiling
Holes in
Mounting Bracket
with supplied screws
Hook
3
2.
Align the mounting slots of Access Point with the hooks of the
mounting bracket
Mounting
Bracket
(Mounting slots of Access Point
securely aligned with
hooks of mounting bracket)
4
3.
Slightly push the Access Point towards the mounting bracket and
slide the hooks out from the mounting slots.
Unmounting of ion8i Access Point
WARNING: Insecure mounting might damage the device or cause
injury. IO is not responsible for damages incurred by insecure wall or
ceiling mounting.
Slide Access Point
out from hooks
Push the
Access Point
5
1.
The Access Point can be powered up using PoE Adaptor or AC
Adaptor (12V) as shown below:
Getting the ion8i Online
Step 1: Power up
Power up using PoE Adaptor
Note: The Reset button serves two functions:
Restart: Press and release the Reset button quickly.
Restore to Factory Default Settings: Press and hold the Reset button
for more than five seconds.
Power up using AC Power Adaptor
AC Power Adaptor
PoE Adaptor
Cat-5
6
Follow the steps mentioned below and connect the Access Point to
a network through GUI:
1. Connect an Ethernet cable to the computer.
2. Connect the other end of the Ethernet cable to the LAN port on
the ion8i Access Point.
Step 2: Connect to the network
(Laptop/Computer)(Ethernet Cable)
7
3. Open the web browser and enter the Access Point static IP
address in the address bar: 192.168.1.1
4. A login screen will appear.
www.ionetworks.in for detailed information on GUI features.
NOTE: Refer the respective user manual on our website
5. Enter the default login credentials as provided with your ion8i
Access Point.
8
Step 3: Check the LED status
Observe the following safety precautions to avoid damage to the
ion8i Access Point:
4. Do not wipe the device with a damp cloth.
5. Do not open the enclosure of the Access Point.
2. Keep away from high voltage cables.
6. Fasten the device tightly with the mount.
1. Do not subject the device to high temperatures.
3. Disconnect the device before cleaning it.
2.4 GHz LED
(Blinks in blue color when
the wireless network interface
comes up)
5 GHz LED
(Blinks in blue color when
the wireless network interface
comes up)
VENT
(Transfers the heat
in ambient)
POWER LED
(Blinks in blue color to notify
the user that the device is
powered ON)
9
Contact us:
Email: iosupport@hfcl.com
Website: www.hfcl.com
www.io.hfcl.com
8, Commercial Complex, Masjid Moth
Greater Kailash-II, New Delhi-110048
©HFCL Limited. All rights reserved. IO logo is registered trademarks of HFCL Limited
Specifications are subject to change without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

iO ion8i Access Point User guide

Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI