CT5SMTBTCHA

Certa CT5SMTBTCHA User guide

  • Hello! I am an AI chatbot trained to assist you with the Certa CT5SMTBTCHA User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What safety precautions should be taken when using this battery charger?
    What type of batteries is this charger suitable for?
    What is the charging current of this charger?
    What battery voltages does this charger support?
    What is the battery capacity range that this charger can handle?
    How do I know when the battery is fully charged?
    What should I do if the fault indicator light is illuminated?
SMART BATTERY CHARGER
CT5SMTBTCHA
Ensure to read all instructions and warnings in this user guide prior to first use. Retain this
user guide for future reference.
This charger is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning the use of the charger by a
person responsible for their safety.
Children must be supervised at all times to ensure they do not play with the appliance.
This charger is designed for consumer use. Do not use this charger for commercial or
any other use.
This charger is only suitable for lead-acid batteries and should not be used to recharge
NiCad or any other non-specified types of battery.
When a normal lead-acid battery is being charged, the release of gas may cause the
fluid to bubble. As the gas is flammable, keep the area ventilated and free of naked
lights.
Avoid getting battery fluid (electrolyte) on your skin or clothes. It is acidic and can cause
burns. If this occurs, you should rinse the affected area with water immediately.
Never charge a frozen battery. If the battery fluid (electrolyte) is frozen, take the battery
to a warm area and allow it to thaw before you begin charging.
Do not touch the battery clamps together when the charger is on.
Only connect and disconnect the battery leads when the power cord is unplugged.
Do not allow the power cord to be exposed to water, heat, direct sunlight, or overhang
where it can be pulled or otherwise be damaged or pose a hazard.
This appliance contains no user-serviceable parts. Do not attempt to repair the charger
yourself.
If the power cord is damaged, stop use immediately and contact help.Kogan.com for
assistance.
Never place a battery on top of the charger or vice versa.
Do not use with an extension cord unless necessary and if so, ensure it is suitably rated
and handled safely along with the charger’s power cord.
If the charger is dropped, impacted, or otherwise damaged, stop use immediately and
contact help.Kogan.com for assistance.
Cleaning and care
Handle with care and inspect regularly to ensure the charger is in good working order.
If this charger, power cord, or plug shows any signs of damage, unplug and stop use
immediately. Contact help.Kogan.com for assistance.
Keep the battery charger in a clean, dry area while not in use.
SAFETY & WARNINGS
For batteries with cell caps (maintenance required)
Remove the battery from your car to avoid possible damage to the alternating
current generator.
To avoid damage to the car body from possible battery fluid spills, it is advisable to
completely dismantle the battery.
Remove the covering caps from the battery cells and only replace them after the
charging procedure, so that any gases which build up during the charging procedure
can dissipate. It is unavoidable that some acid will spill during the charging
procedure.
Check that the level of liquid in each battery cell is above the recommended filling
mark. If not, then the cell must be filled up with ionised or distilled water.
For batteries without cell caps (maintenance not required)
When charging batteries without cell caps, carefully follow the battery manufacturer’s
instructions.
BEFORE FIRST USE
Note:
Do not use tap water.
OVERVIEW
Charging indicator
Full indicator
Fault indicator
1. Attach the positive battery charger leads (red) to the positive connecting terminal of
the battery, indicated by “P” or “+”.
2. Attach the negative battery charger leads (black) to the negative connecting
terminal of the battery, indicated by “N” or ”.
3. Plug your trainer charger unit into a domestic power socket. The charger may take up
to about 7 seconds to determine if a 6V or 12V battery is being connected. The
charging indicator will then illuminate, and the battery will begin charging.
4. When the full indicator illuminates, the battery is completely charged. The charger
will then switch to the floating operation mode (periodically charging to maintain a
100% charge).
5. Unplug the power cord to turn the charger off.
Charging current 1.0A
Battery voltages supported 6V/1A, 12V/1A
Battery capacity Suitable for 4.0Ah 120Ah lead-acid batteries
Charges batteries of 6V/1A and 12V/1A
OPERATION
Note:
Ensure good contact is made between the crocodile clips and the connecting
terminals.
SPECIFICATIONS
Note:
The battery charger automatically will switch to standby if the direct current
cable clamps are removed from while the power cord is still connected to power.
Problem Possible cause Solution
The indicators are lit up/
there is a buzzer sound. Incorrect polarity
Pull out the power cord,
correct the polarity and
reconnect.
The fault indicator is
illuminated.
Low battery voltage - < 3V (6V
battery); < 8V (12V battery).
High battery voltage - > 15V
(12V battery); > 7.5V (6V).
Repair or replace the
battery.
The battery has stopped
charging. The battery has short-circuited. Repair or replace the
battery.
TROUBLESHOOTING
NOTES
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
/