LNC A04837 User manual

Brand: LNC

Model: A04837

Type: User manual

The LNC A04837 is a stylish and versatile light fixture that can be used to create a warm and inviting ambiance in any room. With its adjustable chain, you can customize the hanging height to suit your needs. The fixture's unique design, featuring a combination of metal and wood beads, adds a touch of rustic charm to any décor. Installation is simple and straightforward, and all the necessary hardware is included.

+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST homecustomercare@outlook.com

Page: - 1 - / 4

Item Number: A04837

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

»Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

»Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.

Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs

get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may

occur. It must be understood that common sense, caution and care must be used with any electrical

products.

IMAGE FOR FINISHED PRODUCT:

ORDERING PARTS.

Keep this sheet for future reference in case you need

to order replacement parts. All parts for this fixture can

be ordered from the place of purchase. Be sure to use

exact wording from illustration when ordering parts.

CLEANING.

To clean, wipe the fixture with a soft cloth. Do not use

abrasive materials such as scouring pads or powders,

steel wool or abrasive paper.

+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST homecustomercare@outlook.com

Page: - 2 - / 4

PARTS TYPE & QTY INCLUDING:

(D) Green ground screw (1)

(E) Canopy (1)

(F) Collar ring (1)

(G) Collar loop (1)

(H) Quick link (2)

(I) Chain (1)

(J) Loop (1)

(K) Upper cover (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all

parts and accessories are included as shown in the above

illustration.

2. Make pre-installation

ACCESSORIES & QTY ENCLOSED:

(A) Wire connector (3)

(B) Mounting screw (2)

Philips Head or Flat

Blade Screwdriver Electrical Tape Pilers Wire Cutter/Stripper

Ladder

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

(L) Hex nut (1)

(M) Iron plate (1)

(N) Wood bead strand-A (24)

(O) Stem (1)

(P) Sockets assembly (1)

(Q) Iron frame (1)

(R) Tube (1)

(S) Lower cover (1)

(T) Wood bead strand-B (24)

+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST homecustomercare@outlook.com

Page: - 3 - / 4

3. Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity

until the work is done.

Step A1 »

Step A2 »

Screw stem (O) onto the top of sockets assembly (P).

Pass fixture wires through iron plate (M) and secure it with hex nut (L).

Hang all the wood bead strand-A (N) on iron plate (M) and iron frame (Q).

Step B1 » By measuring, determine the correct number of links needed for proper hanging height. Using the

chain pliers, disconnect and discard the unwanted part.

Attach quick link (H) to chain (I) and loop (J) on the top of upper cover (K).

Carefully weave the fixture wires through chain (I) in and out of every other link and stop just when

you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.

Step B2 »

Step B3 »

4. Make installation

»Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

»Place the wall switch in the “OFF” position.

Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting

screws (B).

NOTE: the side of single bar (C) marked "GND" must face out.

Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position.

Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to the following note, you

would know the proper position where collar loop (G) should be located.

NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should

be screwed enough threads (no less than 6 threads) on the pre-assembled

threaded nipple for more secure hanging.

If not, adjust collar loop (G) on single bar assembly (C) by screwing collar loop

(G) in or out of single bar (C) until the secure length is achieved.

Step C3 » Pass chain (I) through collar ring (F) and then through canopy (E).

Step C4 » Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H).

Pass the fixture wires through collar loop (G) to the top of the pre-assembled threaded nipple and

gently pull to ensure the wires are not stressed.

Step A3 » Pass fixture wires through upper cover (K) and secure it with loop (J).

+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST homecustomercare@outlook.com

Page: - 4 - / 4

Connect ground wires according to the below chart Connect wires according to the below chart

5. Check everything is already installed properly, then you could turn on the light. Enjoy!

Step C5 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured

above single bar (C) is at least 6".

Twist wires together with plastic wire connectors until tightly joined, and wrap each

connector with approved electrical tape. Be sure that no wire strands are exposed

and then carefully tuck all wires into the outlet box.

Step C6 » Make wire connections

Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE

COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Step C7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto

collar loop (G).

Step C8 » 1) Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the

socket.)

2) Screw tube (R) onto the bottom of sockets assembly (P).

3) Carefully hang all the wood bead strand-B (T) on iron frame (Q) and lower cover (S).

LNC A04837 User manual

LNC A04837 User manual

Related papers

Other documents