Brilliant 19847 User manual

Brand: Brilliant

Model: 19847

Type: User manual

Brilliant 19847 is a 2-Light Heater with an Exhaust Fan and CCT LED Light. It provides instant heat, removes moisture, and illuminates your bathroom with adjustable color temperature LED lighting. The heater lamps are not designed for continuous use for more than 30 minutes, but the LED light and exhaust fan can be used continuously. Installation should be done by a qualified electrician, and the unit must be properly earthed/grounded. Enjoy the warmth and comfort of your bathroom with Brilliant 19847.

Please read all instructions before commencing installation even if you are familiar with this type of products.

The HORIZON 2L Heater with exhaust fan and LED light must be installed by qualified electrician.

Keep this document handy for future reference. 1

THIS FITTING MUST BE INSTALLED BY A QUALIFIED ELECTRICAL CONTRACTOR in

accordance with the latest AS/NZS 3000 and relevant amendments

HORIZON Model No.: 19847

2Light Heater with Exhaust fan and CCT LED light

FOR YOUR SAFETY:

•To prevent electrical shock, please ensure that power is DISCONNECTED before installing.

• Be aware of the height of your installation. Refer to ‘Working at Heights “ guide from your local or State

Authorities.

•This product must be used only as described in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, or injury to persons. If you have questions, contact the supplier or

local agent.

•All wiring must be carried out by a licensed electrician in accordance with all applicable national / local codes and

standards. Also check with the local council regulations regarding installation of exhaust fans.

•When cutting into the ceiling material, care must be taken to ensure you do not damage the existing ceiling

structure, existing electrical wiring and other hidden utilities.

•The heater must be properly earthed/grounded.

•The lamps are extremely hot when in use. Do not touch the lamps with any part of your body when in use. Allow

all lamps to cool sufficiently before touching or replacement.

•For the purpose of avoiding any fumes leaking into your bathroom, the duct for the heater must not be laid

together with ducts for air-fuelled water heaters or other open-fire appliances.

•Power cable used for wiring must be appropriately rated . ( Preferred minimum 10A load).

•Any alterations or additions to building wiring must be completed by a licensed electrician or person authorised

by legislation to work on the fixed wiring of any electrical installation

•The heat lamp is not suitable for continuous use for more than 30 minutes.

Note: The LED light and the exhaust fan can be used continuously.

DRAFT V2

Before Installation

•A few minutes planning can make a big difference to the installation time and also to your satisfaction with

the function of your product.

•Remove heat globes from the unit before installation to prevent breakages.

•Before commencing any cutting, check in the ceiling space that there are no obstructions such as ceiling

joists (at least 50mm clearance) and that there is sufficient height clearance (at least 220mm) from the unit.

Check if the electrical wiring can be routed from the wall switches to the mounting location.

•Ceiling insulation should be kept well clear away from the unit and all ducting equipment.

•The unit should not be installed directly above a shower or bathtub. Refer to the ‘zones’ in bathroom in

AS/NZS 3000.

•The unit must not be installed where it will be subject to direct splashing.

•This product is designed for installation in flat ceilings only. Don’t mount on a sloping ceiling or a vertical

wall.

•The Infra-Red lamps are not designed to heat the entire room area, they provide instant heat to persons

standing directly underneath them. Install your unit above the area where ‘drying off’ usually occurs.

•Your heater lamps are not designed for extended periods of operation, as this could cause overheating of

the heater lamps and premature failure.

•For exhaust fan to work efficiently an equivalent volume of air must enter the room being extracted.

Generally, air would be drawn under the door, or through a slightly open window. If the room is airtight, the

fan will operate poorly.

Introduction

Please read these instructions carefully prior to installation and operation. Care should be taken when installing

to prevent damage to the unit.

HORIZON Model No.: 19847

2Light Heater with Exhaust fan and CCT LED light

INSTALLATION

1. The 2L Heater and has been designed for use on ceilings around 2.4 in height.

2. The unit may be installed between joists using the built in clips. Alternatively the unit can be installed

against a joist using a screw through the flange plate.

3. Remove all lamps from your Bathroom Mate. Unfasten the fascia-retaining springs inside the housing,

and remove the fascia.

4. Mark the ceiling with a pencil outline 345mm x 185mm, and cut out a hole in the ceiling at the chosen

area. The instruction card can be used as a template. Make sure a distance between the edges and

wall is no less than 400mm, a minimum 220mm clearance above the unit, and a minimum 50mm

clearance from ceiling joints. Fig.1

5. Insert the Bathroom Mate unit into the hole, ensuring that the side springs are pulled inwards so that

the unit can pass through the hole, without damaging the plaster. Fig.2

6. Securely fix the unit with the clips, and if required, additional screws can be used to assist unit

retention in the ceiling. NB: Screw holes are provided in the flange for this purpose.

7. Replace the fascia, by holding against the unit in ceiling, and reattach the retaining springs inside the

housing. Fig.3

8. Reinstall the two heat globes by screwing them carefully into the lampholder, without over-tightening.

9. Install the central light globe by screwing it carefully into the lampholder, without over-tightening.

10. For installation where external venting is required or is your choice, select a suitable location either in

the roof or exterior wall to vent out the exhausted air/steam and cut out a 105mm hole.

11. Put the ventiduct into the vent hole and seal the space around the hole using a suitable sealant and

cowling where necessary.

12. Fit the in-house end of the duct to the fan outlet, and fix the end with duct clip. Ensure that the ducting

is kept as straight as possible.

1) The recommended height of the installation is 2.4m. Before commencing installation remove the heat globes

from the unit to prevent breakages. Before commencing cutting ensure that the area behind the intended

location is clear of all cables, pipes and joists. Use the card provided as a template to mark the ‘cut out hole’

on the ceiling. The cut out hole size is 355mm x 200mm, ( Fig. 1) Once clear, cut out the section along the

marked lines. The unit may be mounted either between joists using the inbuilt clip fasteners or against a joist

using a screw through the flange plate.

2) Undo the front cover ( Fig.2) by detaching the 4 x springs.

3) Remove the terminal cover on the rear of the base and connect wires as per wiring diagram on Fig. 7 and

wiring instructions. Replace the cover.

4) Note : Connect ducting (if required) after the unit is installed in the ceiling.

5) Gently insert the unit into the cut out hole ensuring to move the side mounting clips inwards so that the body

can pass through the hole without damaging the plasterboard. Tighten the screws for the clips ensuring that

the unit is held securely in place by 4 x clips. Additional screws can be applied around the metal flange plate

to hold the unit to the ceiling. (Fig.3)

6) Hold the fascia against the body of the unit and the ceiling then reattach the securing spring clips to hold the

fascia back in place. (Fig.4).

7) Screw the two large heat lamps into the E27 lampholders. Ensure connection is firm do not over tighten.

(Fig.5)

8) Attach ducting if required ( Fig.6) to extract the air to the outer wall using 1.5 long flexible ducting, cable ties

and vent outlet grill provided. Fix and tighten the cable ties firmly to hold the flexible duct to the unit and the

outer wall vent.

NOTE: Ensure that the flexible duct, when connected to the unit doesn’t obstruct or block the anti-draft

stopper, as it would reduce the overall airflow.

9) Check that all connections are secure.

10) Turn the power ON.

11) You can operate the unit using the wall switch.

Installation 1) Before commencing installation remove the heat globes from the unit then remove the front cover by

detaching the 4 x springs and unplug the LED downlight cable.

Before commencing cutting ensure that the area behind the intended location is clear of all cables, pipes and

joists. Use the card provided as a template to mark the ‘cut out hole’ on the ceiling. The cut out hole size is

355mm x 200mm. Once clear, cut out the section along the marked lines. The unit may be mounted either

between joists using the inbuilt clip fasteners or against a joist using a screw through the flange plate.

2) Remove the cover terminal cover on the back of the base and connect wires as per wiring diagram Fig. 6

and wiring instructions. Replace the cover.

1) Remove 2 heat lamps from the bathroom heater. Then remove the plug of the Led downlight inside the

housing. Unfasten the fascia retaining spring clips inside the housing ,and remove the fascia. Connect the

ducting if required to the outer grill of the unit. Insert the unit into the square hole being sure to pull the side

springs inward so that the body can pass through the hole without damaging the plaster. Ensure that the unit

is held securely in place by the clips. If required, additional screws can be used to aid holding the unit in the

ceiling. Screw holes are provided in the flange for this purpose. (Fig.3)

2) Hold the fascia against the body of the heater and the ceiling and attach the securing spring clips to hold the

fascia in place. (Fig.4)

3) Now screw in the two large heat lamps into the lamp holder through the holes provided in the fascia.The

globes should be screwed up firmly to ensure a good electrical contact but don’t over tighten. (Fig.5)

HORIZON Model No.: 19847

2Light Heater with Exhaust fan and CCT LED light

355mm

Fig.2

Fig.3 Fig.4

Fig.5

Cut out size hole

Fig.1

Cut out aperture

Spring Spring

Undo front fascia(

cover)

Fig.6

1.5m x 125mm flexible

duct Vent outlet

LED

Air outlet point

Draft stopper

Connect it

to the unit

Connect it to the

vent outlet grille

Connect it to

the unit with

cable tie

Connect it to the

vent outlet grille

with cable tie

1.5m x Φ125mm flexible

duct Vent outlet grille

FIG 3 - connections

Lin

IN ~ 240VAC

Sensor

Relay

Same load can be switched with multiple sensors if

required.

Figure 3a shows two sensors switching one load.

FIG 2 – terminal block

Electrical wiring diagram

Operation

Your Brilliant Horizon Heater lamp uses Infrared heating lamps as a heat source. It also has an exhaust fan and

an LED light.

•Heating: Switch the ‘Heat’ button ‘ON’ on the wall switch. The heat globes provide instantaneous heat from

the moment they are switched ‘ON’.

•Exhaust Fan: Use the switch button ‘Fan’ to turn it ON and Off.

•CCT LED Light: Operate the LED light independently from heat globes, using ‘Light’ On /Off switch button.

•Change LED Light Colour Temperature: The colour temperature of CCT LED can be changed between

3000K, 4200K and 6000K. To change colour temperature, switch ON the light first, then switch the light ‘OFF -

ON - OFF - ON’ within 3 seconds

The wiring diagram is shown on Figure 7.

The unit requires ‘permanent active’. The fitting is fitted with a thermostat which will turn the motor ( FAN) ‘ON’

when the temperature exceeds 80C.

1) Double pole disconnecting device (K) must be fitted in the circuit.

2) Ensure the power is switched “OFF” at the mains before commencing installation.

3) Remove the cover on the back of the enclosure to access the terminals.

4) Connect wires as per electrical wiring diagram above. Ensure connections are firm and secure.

5) Replace the cover removed earlier.

Note: Red warning label must be permanently displayed on the cover of the unit

WARNING: Permanent Active! Isolate at main switchboard before removing cover.

Figure 7.

HORIZON Model No.: 19847

2Light Heater with Exhaust fan and CCT LED light

Cleaning

•Switch off the power before commencing cleaning and wait until the globes cool down.

•Regularly wipe globes and front fascia with soft cloth soaked with water or neutral detergent if required.

•Clean the exhaust fan from dust and dirt with dry or wet cloth if required.

•Clean the exhaust ducting kit and ensure airways are clean and there are no obstructions at the exit

from the wall.

Inside the fitting

Then the objects

reradiate the heat back to

the environment.

Specifications

Model No

19847/05 -White and 19847/11- Silver

Fascia colour

/05- White ; /11- Silver

Voltage and power

230V or 240V AC 50Hz 633W Max.

Heat Lamps

2 x 275W , 240V AC, R125, E27

Motor

75W

CCT LED

3000K, 900lm; 4200K, 1050lm; 6000K, 1000lm;

9W, Non dimmable

Air Movement

<300m3/h (at exit point from the unit)

Cut out hole size

355mm x 200mm

Dimensions

Length 419mm x Width 244mm

x Depth 210mm

Accessories

Aluminium duct Φ125mm by 1.5m with fixing

clamps and vent outlet grille- included

Switch

3-way gang switch, SAA approved- included

Noise

45 dB

IP rating

IP X2 ; IPX4 LED globe only

PTC

80C

Weight

3kg

Installation in

bathrooms

Suitable for Installation in Zone 2 and Zone 3

in bathrooms as per AS/NZS 3000.

NOTE: Not suitable for installation in Zone 1

and Zone 0.

HORIZON Model No.: 19847

2Light Heater with Exhaust fan and CCT LED light

150mm

Clearance above the unit

Clearance sideway from

joists

Horizon 2L Heater

with exhaust fan and

Led light Model No

19847

Ceiling cavity

area

50mm

Horizon

2L Heater with exhaust

fan and LED light Model

No 19847

Clearance distances from the unit:

Minimal clearance distances:

TBC

250mm

Clearance from

internal walls

NOTE:

Distances to be

confirmed by

LABORATORY

testing .

TEST REPORT

MUST BE

PROVIDED!

150mm

Clearance above the unit

Clearance

sideway from

joists

Ceiling cavity

area

50mm

Horizon

2L Heater with exhaust

fan and LED light Model

No 19847

250mm

Clearance from

internal walls

Warranty:

Brilliant Lighting warrants this product against defects in manufacture and workmanship for a period of 3 years from date of

purchase. For products used in non-domestic or commercial applications, Brilliant Lighting warranties this product for a period of

3 months from date of purchase. This warranty is only valid for products installed by a qualified electrical contractor and operated

within the guidelines specified by Brilliant Lighting, and within the correct operating voltage ranges as stated on the product’s

rating label.

Warranty does not include damage or loss arising from incorrect installation, operation or maintenance of this product, damage

caused through modification, incorrect installation, service by unqualified or unauthorised personnel or lack of regular

maintenance and cleaning. Proof of installation by qualified personnel may be required, eg. Electrical Safety Certificate. Proof of

purchase must be supplied with all warranty claims.

This warranty is provided in addition to any other rights and remedies of the customer under any law. In applications not

intended for household, personal or domestic use, liability is limited to replacement or reimbursement of product only.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a

replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also

entitled to have the goods repaired or replaced if goods fail to be of acceptable quality and the failure does not amount to a

major failure.

Any claim under this warranty must be made within the specified warranty period from date of purchase of this product. To make

a claim under the warranty, take the product (with proof of purchase – receipt or similar) to the store where you purchased the

product or contact Brilliant Lighting at the address below.

This warranty is given by:

Brilliant Lighting (Aust)Pty. Ltd.

ABN 37 006 203 694

956 Stud Road Rowville, VIC 3178

Phone: 03 9765 2555

Email: [email protected]

MADE IN CHINA

HORIZON Model No.: 19847

2Light Heater with Exhaust fan and LED light

Brilliant 19847 User manual

Brilliant 19847 User manual

Brilliant 19847 User manual

Related papers

Other documents