2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Innovative
  6. STX-1000-8510 Staxx Articulating Monitor Plus Laptop Mount

Innovative STX-1000-8510 Staxx Articulating Monitor Plus Laptop Mount User manual

  • Hello! I'm your chat assistant and I've reviewed the installation instructions for HAT Collective's STX series desk mounts. This document covers various models including STX-450, STX-500, STX-600, STX-800, STX-1000 and their -8510 variants. It details both desk clamp and thru-desk installation methods, parts lists, and how to adjust the tilter friction. I'm ready to help answer your questions about the setup and features of the mount.
  • What is the maximum desk thickness for desk clamp configuration?
    What tool is needed for desk clamp configuration?
    What tool is needed to adjust tilter friction?
STA X X
Installation Instructions
STX-450
STX-500
STX-600
STX-800
STX-1000
STX-450-8510
STX-500-8510
STX-600-8510
STX-800-8510
STX-1000-8510
™
© 2021 Innovative Ergonomic Solutions REV A
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
HAT Collective
408 437 8770
cs@hatcollective.com
hatcollective.com
PAGE 1 OF 14
A Top Down Mount
8524
B Dimpled Pole
110607-14
C Stackable Mount
413054
D Pole Collar
113332
E Pole Clip
113449
F Dog Washer for Articulating Arms
113704
G Rotation Stop for Articulating Arms
113705
H M6 x 1mm Phillips Pan Head Screw
105304
I Quick Connect VESA Plate
114808
J M4 x 12mm Phillips Pan Head Screw
701153
K Monitor Tilter
8500 Tilter
L Dog Washer
105189
M 10-32 x 3/8" FPhMS w/Lock Patch
705198
N Pole Cap
105195
O Cable Clip
104533
P Cable Cap
102043-5.125 (3500 arms)
114810 (7000 arms)
Q Forearm Cable Cap
115584
R 1/8" Allen Wrench
701312
S 3/32" Allen Wrench
700146
T 7/32" Allen Wrench
701127
U* M8 x 95mm SCHS
716061
V* Spacer
701544
W* Lock Nut
710015
X** Laptop Holder
8510
Y** Split Washer
701910
Z** Coupling Nut
716187
* Included with optional thru-desk kit only, model # 8524-TM-CK (sold separately).
** Included with STX-XXX-8510 only.
PARTS LIST
PAGE 2 OF 14
T
A
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
DESK CLAMP CONFIGURATION
OR
PAGE 3 OF 14
3 4
THRU-DESK CONFIGURATION*
T
U
V
W
7/32"
Desk thickness
up to 1.5" (3.8 cm)
* Thru-desk kit required, model # 8524-TM-CK (sold separately).
PAGE 4 OF 14
B
C
D
i
IMPORTANT:
When inserting
pole into mount,
the dimples
should be aligned
perpendicular to
the rear edge of
mounting surface.
Dimples
S
3/32"
5
PAGE 5 OF 14
6
E
PAGE 6 OF 14
F
F
G
G
H
H
iIMPORTANT:
Install part (G) in the
orientation as shown to
the left. When washer,
part (G), is installed
correctly, the arms will
not rotate past the back
of the mount.
F
7
PAGE 7 OF 14
8
J
J
I
PAGE 8 OF 14
9
K
PAGE 9 OF 14
10
L
M
iTILTER FRICTION ADJUSTMENT
R
1/8"
PAGE 10 OF 14
L
W
Y
Z
M
M
ARE YOU INSTALLING STX-XXX-8510?
IF NOT, PLEASE CONTINUE TO STEP 16.
11
14
12 13
15
PAGE 11 OF 14
16
iIn some instances, an
additional counterbalance
adjustment may be needed
to allow the arm’s instant
height adjustment function
to work properly.
If your arm is not staying in
position after performing
step 16, tighten the adjustment
screw with a 1/8" Allen wrench.
Tighten the adjustment screw.
1/8"
T
7/32"
PAGE 12 OF 14
17
2x
PAGE 13 OF 14
N
P
O
18
P
O
Q
2x
2x
PAGE 14 OF 14
/