■
Standard :
IEEE 802.3 10Base-T, 802.2u 100Base-TX, 100Base-FX,
Supports Full/Half Duplex
Maximum Transmission Unit is 1552 bytes in size.
■
100Base-TX UTP Cable :
Cable type 100base-TX; Category 5 or better
Maximum cable distance : 100 meter (328 feet)
■
Fiber Optic Connectors :
Connector type : SC, ST, FC
Multi-mode : 1310nm, 2km
Single-mode : 1310nm, 1550nm. 15 / 30 / 50 / 80 / 120km
Single Fiber : A type 1310nmTX /1550nmRX, B type 1550nmTX /1310nmRX 20 / 40 / 60 / 80km
■
Power :
DC 12 ~ 48VDC In for Power 1 and Power 2
■
Relay Output(max)
Load Voltage: 40V(AC Peak or DC)
Load Current: 1.5A
Output Power: Dissipation: 1.8W
■
Dimensions :
62.5 x 106 x 134.8 ( W x D x H ) mm
■
Weight :
650g
■
Certication :
CE, FCC, LVD, RoHS
Environment
Standard for model : IFC-1200
Operating Temperature : 0°C ~ 60°C
Storage Temperature : -10°C ~ 70°C
Humidity : 0 ~ 90%, (non-condensing)
Wide Range for model : IFC-1200X
Operating Temperature : -40°C ~ 85°C
Storage Temperature : -40°C ~ 85°C
Humidity : 0 ~ 90%, (non-condensing)
Wide Range for model : IFC-1200X-1
Operating Temperature : -30°C ~ 85°C
Storage Temperature : -40°C ~ 85°C
Humidity : 0 ~ 90%, (non-condensing)
■
www.ctcu.com
www.ctcu.com
Industrial Fiber Media Converter
•
Two ports 10/100Base-TX and one port 100Base-FX
•
IFC-1200
•
IFC-1200X
•
IFC-1200X-1
User Guide
Panel Specications
Figure #1. Top and Front View of IFC-1200(X)
CTC Union Technologies Co., Ltd.
www.ctcu.com
Description
The IFC-1200 is industrial grade ber media converter that provides
2-port 10/100Base-TX and 1-port 100Base-FX. The reliable hardware design is
suitable for keeping industrial automation application running continuously. Each
IFC-1200 media converter comes with two relay output alarms and two redundant
DC power inputs to help prevent damage and loss. The IFC-1200 media converter
is available in models that support operating temperatures of 0 to 60 degree C, or
Wide Range temperatures of -30°C ~ 85°C or -40°C to 85°C degree C.
Features
■
2-port 10
/
100Base-TX to 100Base-FX
■
Auto-Negotiation on two LAN port
■
Auto MDI
/
MDIX
■
Forward 1552 bytes (Max.) packets
■
Supports Q in Q double tagged frame transparent
■
Supports IEEE 802.1q Tag VLAN pass thru
■
Support f low control (Pause)
■
Supports Far End Fault
■
Supports two Relay out, power or optical f iber failure alarm by relay output
Solid state relay, Arc-Free with no snubbing circuits
■
Support DIN-Rail and Wall Mount
■
-40°C ~ 85°C degree C Operating Temperature Range
■
Supports Redundant dual DC power inputs
LED Indicator
Optic Fiber
LAN1
LAN2
DIP Switch
V.: 1.0
■
Top View
PWR1 PWR 2 ALM
OPT
OPT
LAN1
LAN2
TX
RX
LAN1 LAN 2
ON OFF
ALM1
ALM2
IFC-1200
Termial Connector 1
Termial Connector 2
Top View
Installation
www.ctcu.com[email protected]
www.ctcu.com
www.ctcu.com
Figure #2. Rear panel with DIN-Rail Kit of IFC-1200(X) Figure #3. Rear panel with Wall Mount Kit of IFC-1200(X)
Dip Switch Setting
ON
SW1
SW2
OFF
Terminal Connector 1
V.: 1.0
Relay 1 alarm Enable Relay 1 alarm disable
Relay 2 alarm Enable Relay 2 alarm disable
LED State Status
Power 1 is on
Power 2 is on
Fault (Power or f iber failure)
Fiber Link/Act
LAN 1 Link/Act
LAN 2 Link/Act
Green
Green
Red
Green
Green
Green
1
2
3
4
5
6
ON
SW1
SW2
Pin 1 – Power 1 V+
Pin 2 – Power 1 V-
Pin 3 – Power 2 V+
Pin 4 – Power 2 V-
1
2
3
4
1
2
3
4
Terminal Connector 2
Pin 1 – Relay 1 COM (Power Failure Alarm)
Pin 2 – Relay 1 NO (Normal : Close , Alarm : Open)
Pin 3 – Relay 2 COM (Optic Fiber Failure Alarm)
Pin 4 – Relay 2 NO (Normal : Close , Alarm : Open)
123
456
LED Indicator
DIN-Rail Kit View
Rear Panel View Rear Panel View
Wall Mount Kit View
/