INSTALLATION INSTRUCTIONS
GB-PIPE1/GB-PIPE1B
Pipe-Mounted Equipment Enclosure
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
Phone: 800-368-9700
Fax: 800-832-4888
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
AUSTRALIA, NEW ZEALAND, OCEANIA
(DISTRIBUTOR)
P.O. Box 295
Mordialloc Victoria 3195
Australia
Phone: 039586 6330
www.premiermounts.com.au
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2008
9534-004-003-00
Page 2 Installation Instructions
Table of Contents
Warning Statements
GB-PIPE1
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND
COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND
PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED
ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS,
ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER
RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE BOX. IF NOT, THE
CEILING STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT
IS 75LBS. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE
INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL
INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY
GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
At least two qualified people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the
product.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact
Contact Premier Mounts with any questions
(800) 368-9700
Warning Statements 2
Parts List 3
Installation Tools 3
GB-PIPE1 Installation 4
1-1/2” NPT Installation 5
PDS-PLUS Installation without NPT (Optional) 6
Cable Connections 7
Side Panel Installation 7
Lateral Shift Adjustment 8
Technical Specifications 8
Warranty 9
Installation Instructions Page 3
Parts List
This accessory is shipped with all proper installation hardware and components. Make sure that none of these parts
are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Premier Mounts (800-368-9700).
Installation Tools
Equipment Tray (Qty 1)
M4 x 8mm Security Head Screw (Qty 10)
M5 Security Wrench
GB-PIPE1
M3 Security Wrench
M8 x 12mm Security Head Screw (Qty8)
Side Panel (Qty 2)
Upper Plate (Qty 1)
M5 x 10mm Security Head Screw (Qty4)
Page 4 Installation Instructions
GB-PIPE1 Installation
Step 1. Determine where the GB-PIPE1 will be
located.
Step 2. Install your 1-1/2” NPT or ceiling adapter.
Step 3. Attach the upper plate to the NPT or
adapter by rotating counter-clockwise.
Step 4. Use an M3 security wrench to tighten the
set screw.
Upper Plate
Step 5. At this time, run all existing cables through
the pipe and down through the upper
plate.
The GB-PIPE1 is designed for use with either a standard piece of 1-1/2” NPT pipe or any available ceiling mount adapter
from Premier Mounts. Please refer to the ceiling mount adapter installation instructions when mounting.
GB-PIPE1
Unpack the Gear Box and review any WARNING statements that apply to the installation. Select the desired location for
the GB-PIPE1.
The upper plate must rotate onto the
threads at least four (4) complete
rotations.
1-1/2” NPT
Set Screw
M3 Security
Wrench
Pipe
Cables
At this time, you may pre-install your
electronic components in the equipment
tray.
Electronic
Component
Installation Instructions Page 5
GB-PIPE1
Mounting Hole
Spring Loaded
Nuts
Step 6. Lift the equipment tray into position.
Upper Plate
Step 7. Line up the mounting holes with the
threaded shaft of the spring loaded nuts.
Step 8. Once the holes are lined up, press down
on the spring loaded nuts and tighten.
Step 9. Insert and tighten two (2) M4 x 10mm
security screws on the upper plate.
Electronic Components
1-1/2” NPT Installation
The NPT must rotate onto the
equipment tray four (4) complete
rotations.
Step 2. Use an M3 security wrench to tighten the
set screw.
Step 3. Attach projector mount to NPT.
1-1/2” NPT
1-1/2” NPT
Equipment Tray
Set Screw
Step 1. Place the threaded end of the 1-1/2” NPT
into the plate hole.
Plate Hole
Before attaching the lower 1-1/2” NPT, it is strongly recommended that all connections in the equipment tray be made at
this time. Once the connections are made, feed the cables through the plate hole and then through the 1-1/2” NPT. Please
read instructions below to complete the installation.
M4 x 10mm
Security
Screws
Please follow the instructions
included with the mount to complete
this step. If using a PDS Series mount,
connection may be made directly to
the bottom of the equipment tray.
Page 6 Installation Instructions
GB-PIPE1
PDS-PLUS Installation without NPT (Optional)
Before attaching the PDS-PLUS, it is strongly recommended that all connections in the equipment tray be made at this
time. Once the connections are made, feed the cables through the plate hole and then through the 1-1/2” NPT. Please read
instructions below to complete the installation.
M5 Security
Wrench
M8 x 12mm
Security Head
Screw
Equipment
Tray
Step 1. Remove the lower mounting plate from
the equipment tray by removing the four
(4) M8 x 12mm security head screws with
an M5 security wrench.
Mounting Slots
Step 2. Locate the mounting slots that are on the
base box bridge of the PDS-PLUS.
Base Box
Bridge
Step 3. Line up the mounting slots on the base box
bridge with the mounting points on the
equipment tray.
Step 4. Insert four (4) M5 x 10mm security screws
and tighten using the M5 security wrench.
M5 Security
Wrench
M5 Security
Wrench
Mounting
Point
Equipment
Tray
M5 x 10mm
Security Head
Screw
Equipment
Tray
Base Box
Bridge
Base Box
Bridge
Please refer to the PDS-PLUS Installation Instructions before proceeding with the following steps.
M5 x 10mm
Security Head
Screw
Be aware of the screen location and
orient the base accordingly.
Installation Instructions Page 7
GB-PIPE1
Cable Connections
Equipment
Tray
Step 1. Pull all cables down through the
PDS-PLUS base box.
Please refer to the PDS-PLUS Installation Instructions before proceeding with the following steps.
Cables
PDS-PLUS
Base Box
Step 2. Pull all cables down through the
PDS-PLUS projector plate.
Step 3. Attach all cables to the installed
projector.
Step 2. Tighten these screws using the M5
security wrench.
M3 Security
Wrench
Side Panel
M4 x 8mm
Security Screw
Step 1. Attach the two side panels using eight (8)
M4 x 8mm security screws.
Side Panel Installation
Side Panel
Side Panel
Cables
Page 8 Installation Instructions
Technical Specifications
All measurements are in inches(mm).
GB-PIPE1
Lateral Shift Adjustment
M8 x 12mm
Security Head
Screw
M5 Security
Wrench
Step 1. Use the M5 security wrench and loosen
the four (4) M8 x 12mm security screws.
Step 2. Once the screws have been loosened,
slide the GB-PIPE1 laterally side to side
(or front to back).
Step 3. When the desired position has been
determined, use the M5 security wrench to
tighten the M8 x 12mm security screws.
Do not completely remove these screws.
Installation Instructions Page 9
GB-PIPE1
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-
PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN
PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-
ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-
ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
/