SV6**D Digital
Series
2
Contents
INSTALLING YOUR TV
Safety Precautions ............................................... 4
Installation and important information ................... 5
The remote control .............................................. 6
Inserting batteries and effective range of the
remote ...................................................... 7
CONNECTING YOUR TV
Connecting external equipment ............................8
Connecting an HDMI™ or DVI device to the HDMI
input ............................................................... 9
To connect an HDMI device ............................ 9
To connect a DVI device ................................ 9
REGZA-LINK connection ....................................10
Connecting a computer .......................................11
To connect a PC to the RGB/PC terminal ........11
To connect a PC to the HDMI terminal ............11
Connecting a home network ................................12
To connect the TV to a home network .............12
Controls and input connections ...........................13
Switching on ...............................................13
Using the remote control ...............................13
Using the controls and connections ................13
SETTING UP YOUR TV
Startup Application ............................................14
Quick Setup ................................................14
Ant/Cable In (if available) ............................15
Auto Tuning ................................................16
ATV Manual Tuning ...........................................16
Tuning ........................................................16
Skip ...........................................................18
Sorting positions ..........................................18
DTV Manual Tuning ............................................19
Manual Tuning ............................................19
Manual Tuning for DVB-C .............................19
DTV Settings ......................................................19
Channels ....................................................19
Auto Channel Update ...................................20
DVB Character Set .......................................20
Dynamic Scan .............................................20
Location setting ...........................................20
Analogue switch-off .....................................20
CONTROLS AND FEATURES
General controls ................................................ 21
Quick Menu ............................................... 21
Selecting positions ....................................... 21
The Time Display – analogue only ................. 21
Stereo and Bilingual transmissions ................. 21
Sound controls .................................................. 22
Volume controls and mute sound ................... 22
Dual .......................................................... 22
Bass, Treble and Balance ............................. 22
Advanced Sound Settings ............................. 23
Dolby Volume
®
........................................... 23
Dynamic Range Control ............................... 23
Audio Level Offset ....................................... 23
Headphone Settings ..................................... 23
Audio Description ....................................... 24
Widescreen viewing ........................................... 25
Picture controls .................................................. 27
Picture Position ........................................... 27
Picture Mode .............................................. 27
Picture preferences ...................................... 27
Reset ......................................................... 28
3D Colour Management ............................... 28
Base Colour Adjustment ............................... 28
Colour Temperature ..................................... 28
Auto Brightness Sensor Settings ..................... 29
LED Backlight Control .................................. 29
Black/White Level ....................................... 29
Static Gamma ............................................. 29
MPEG NR – Noise Reduction ........................ 29
DNR – Digital Noise Reduction ..................... 29
Resolution+ ................................................ 30
Active Vision M200 ..................................... 30
Film Stabilization ........................................ 30
Expert Mode ............................................... 30
Resetting the advanced picture settings .......... 30
Control Visualization ................................... 31
Automatic Format (Widescreen) .................... 31
4:3 Stretch ................................................. 31
Blue Screen ................................................ 31
Side panel adjustment .................................. 31
Picture still .................................................. 31
HDMI Information Display ............................ 31
Using the Media Player ...................................... 32
To select the Auto Start function .................... 32
To open the Media Player ............................ 32
Viewing photo files ...................................... 33
Viewing movie files ..................................... 34
Playing music files ....................................... 35
Using a networked server PC .............................. 36
To open the Media Player ............................ 36
3
Using the Photo Frame feature .............................38
To open Photo Frame ...................................38
Setting the features ......................................38
Other features ...................................................40
Panel Lock ..................................................40
TOSHIBA Illumination ...................................40
The timers .........................................................40
Programme Timers – digital only ...................40
On Timer ....................................................41
Sleep Timer .................................................41
Digital on-screen information and Programme
Guide ............................................................42
Information .................................................42
Guide ........................................................43
Genre selection/searching ............................43
Digital settings – parental control .........................44
Setting the PIN ............................................44
Parental Setup .............................................44
Digital settings – Channel Options .......................45
Channel List ................................................45
Skipping channels .......................................45
Locking channels .........................................45
Digital settings – other settings .............................46
Subtitles .....................................................46
Audio languages .........................................46
Common Interface .......................................46
Software Upgrade and Licenses ...........................47
Auto Upgrade .............................................47
Searching for New Software .........................47
Software Licenses ........................................47
System Information and Reset TV .........................47
System Information ......................................47
Automatic Power Down ................................47
Reset TV .....................................................47
PC Settings ........................................................48
Horizontal and Vertical Position ....................48
Clock Phase ................................................48
Sampling Clock ...........................................48
Reset ..........................................................48
Input selection and AV connections ......................49
Input selection .............................................49
External input skip .......................................49
Input signal selection ....................................49
Woofer setting ............................................49
PC Audio ....................................................50
HDMI 1 Audio .............................................50
HDMI Settings .............................................50
Digital Audio Output ....................................50
Using REGZA-LINK ............................................ 51
Enable REGZA-LINK .................................... 51
TV Auto Power On ...................................... 51
Auto Standby .............................................. 51
Amplifier Control ........................................ 51
Speaker Preference ..................................... 51
REGZA-LINK input source selection ............... 51
REGZA-LINK playback device control ............ 52
REGZA-LINK one touch play ......................... 52
REGZA-LINK system standby ........................ 52
REGZA-LINK system audio control ................. 52
REGZA-LINK PC link .................................... 52
Setting up the network address for the LAN port .... 53
Auto Setup ................................................. 53
Manual Setup ............................................. 53
TEXT SERVICES
Text services ..................................................... 54
Selecting modes .......................................... 54
Text information .......................................... 54
Navigating pages using Auto ....................... 54
Navigating pages using LIST ......................... 54
Control buttons ........................................... 55
PROBLEM SOLVING
Questions and Answers ...................................... 56
INFORMATION
License Information ............................................ 59
Information .......................................................60
Specifications and accessories ............................ 62
4
INSTALLING YOUR TV
Safety Precautions
This equipment has been designed and manufactured
to meet international safety standards, but like any
electrical equipment, care must be taken to obtain the
best results and for safety to be assured. Please read
the points below for your own safety. They are of a
general nature and are intended to help with all
electronic consumer products. Some points may not
apply to the goods you have just purchased.
Leave more than 10cm clearance around the
television to allow adequate ventilation. This will
prevent overheating and possible damage to the
television. Dusty places should also be avoided.
Damage may occur if the television is left in direct
sunlight or near a heater. Avoid places subject to
extremely high temperatures or humidity. Place in a
location where the temperature remains between 5°C
(41°F) min. and 35°C (94°F) max.
The mains supply required for this equipment is 220-
240v AC 50/60Hz. Never connect to a DC supply or
any other power source. DO ensure that the television
is not standing on the mains lead. Use only the
supplied lead.
DO NOT cut off the mains plug from this equipment.
The plug incorporates a special Radio Interference
Filter, the removal of which will impair its
performance.
In the UK, the fuse fitted in the plug is approved by
ASTA or BSI to BS1362. It should only be replaced by
a correctly rated and approved type and the fuse
cover must be refitted.
IF IN DOUBT, PLEASE CONSULT A COMPETENT
ELECTRICIAN.
DO read the operating instructions before you
attempt to use the equipment.
DO ensure that all electrical connections (including
the mains plug, extension leads and inter-connections
between pieces of equipment) are properly made and
in accordance with the manufacturers’ instructions.
Switch off and withdraw the mains plug before
making or changing connections.
DO consult your dealer if you are ever in doubt about
the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors on
equipment.
DO NOT obstruct the ventilation openings of the
equipment with items such as newspapers,
tablecloths, curtains, etc. Overheating will cause
damage and shorten the life of the equipment.
DO NOT allow electrical equipment to be exposed to
dripping or splashing or objects filled with liquids,
such as vases, to be placed on the equipment.
DO NOT place hot objects or naked flame sources,
such as lighted candles or nightlights, on or close to
equipment. High temperatures can melt plastic and
lead to fires.
DO NOT use makeshift stands and NEVER fix legs
with wood screws. To ensure complete safety, always
fit the manufacturers’ approved stand, bracket or legs
with the fixings provided according to the
instructions.
DO NOT leave equipment switched on when it is
unattended, unless it is specifically stated that it is
designed for unattended operation or has a standby
mode. Switch off by withdrawing the plug, and make
sure your family knows how to do this. Special
arrangements may need to be made for people with
disabilities.
DO NOT continue to operate the equipment if you
are in any doubt about it working normally, or it is
damaged in any way – switch off, withdraw the
mains plug and consult your dealer.
WARNING – excessive sound pressure from
earphones or headphones can cause hearing loss.
ABOVE ALL – NEVER let anyone, especially children,
push or hit the screen, push anything into holes,
slots or any other openings in the case.
NEVER guess or take chances with electrical
equipment of any kind – it is better to be safe than
sorry.
Air Circulation
Heat Damage
Mains Supply
Do
DO NOT REMOVE ANY FIXED COVERS AS THIS WILL
EXPOSE DANGEROUS AND 'LIVE' PARTS.
THE MAINS PLUG IS USED AS A DISCONNECTING DEVICE
AND THEREFORE SHOULD BE READILY OPERABLE.
Do not
5
INSTALLING YOUR TV
Installation and important information
Locate the television away from direct sunlight and strong
lights, soft, indirect lighting is recommended for
comfortable viewing. Use curtains or blinds to prevent
direct sunlight falling on the screen.
Place the TV on a stable, level surface that can support
the weight of the TV. In order to maintain stability and
prevent it falling over, secure the TV to the level surface
using the strap located under the table top stand, or to
a wall using a sturdy tie to the clip on the back of the
table top stand.
The LCD display panels are manufactured using an
extremely high level of precision technology; however,
sometimes some parts of the screen may be missing
picture elements or have luminous spots. This is not a sign of a malfunction.
Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will
break or damage the screen. Also please be certain that small items cannot be inserted into slots or openings in
the case.
Cleaning the screen and cabinet…
Turn off the power, and clean the screen and cabinet with a soft, dry cloth. We recommend that you do not use
any proprietary polishes or solvents on the screen or cabinet as this may cause damage.
The digital reception function of this television is only effective in the countries listed in the “Country” section of
the “SETUP” menu. Depending on country/area, some of this television's functions may not be available.
Reception of future additional or modified services can not be guaranteed with this television.
If stationary images generated by 4:3 broadcasts, text services, channel identification logos, computer displays,
video games, on screen menus, etc. are left on the television screen for any length of time, they could become
conspicuous. It is always advisable to reduce both the brightness and contrast settings.
Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at the
4:3 outlines. This is not a defect of the LCD TV and is not covered under the manufacturer’s warranty. Regular
use of other size modes (eg: Super Live) and varying the “side panel” brightness (if available on the model) will
prevent permanent retention.
Where to install
Please take note
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) fire;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s
manual;
viii)any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not
limited to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal
operation or misuse of the product.
NOTE: A Toshiba wall bracket or stand, where available, must be used to maintain the product's BEAB approval.
Stand clip
‘P’ Clip
Sturdy tie (as short as possible)
Fixing strap
Stand style is dependent on model
Fixing strap
6
INSTALLING YOUR TV
The remote control
Simple at-a-glance reference for your remote
control.
1 For On/Standby mode (T/R/D)*
2 To select device mode (T/R/D)
3 Number buttons (T/R/D)
4 Switch the Audio Description On/Off (T)
5 To select external input sources (T)
To select line input (R/D)
6 To alter the TV volume (T/R/D)
7 To mute the TV sound (T/R/D)
8 To access Quick Menu (T)
9 To change programme positions (T/R)
To change text pages (T)
10 To display the digital on-screen Programme Guide (T)
11 To exit menus (T)
12 When using menus, the arrows move the cursor on the
screen up, down, left or right. Press
Q to confirm your
selection (T/R/D)
13 To display on-screen information (T/R/D)
To access index page in Text mode (T)
14 To return to previous menu (T/R/D)
15 Colour buttons Text and interactive service control
buttons (T)
ROOT To display Root Menu (R)
CONTENTS To display Contents Menu (R)
TOP To access Top Menu (R/D)
DVD DVD Menus (R/D)
16
s Stereo/bilingual transmissions (T)
AUDIO To access Audio menu (R/D)
17 SUBTITLE Digital Subtitles or Analogue TEXT Subtitle
pages if available (T)
SET UP To access Setup menu (R/D)
18 Widescreen viewing (T/R/D)
19 To call up text services (T)
20 When in TV mode:
MENU On-screen menus
ATV/DTV To switch between ATV (analogue television)
and DTV (digital television)
LIST To switch between TV and Radio programmes
when in digital mode
r Picture still
D Analogue time display
When in Text mode:
A To reveal concealed text
B To hold a wanted page
C To enlarge text display size
D To select a page whilst viewing a normal
picture
When using the Programme Guide:
Z - 24 hours
z + 24 hours
CC - 1 page
cc + 1 page
REGZA-LINK or DVD mode:
press
V to EJECT
press
v to STOP
press
c to PLAY
press
W/w to PAUSE/STEP
press
Z to SKIP-BACK
press
CC to REWIND
press
cc to FAST FORWARD
press
z to SKIP-FORWARD
* T=TV mode, R=REGZA-LINK mode, D=DVD mode
1
7
8
9
11
12
14
18
19
20
5
2
3
4
6
10
13
15
16
17
7
INSTALLING YOUR TV
Remove the back cover to
reveal the battery compartment
and make sure the batteries
are inserted the proper way.
Suitable battery types for this
remote are AAA, IEC R03
1.5V.
Do not combine a used, old
battery with a new one or mix
battery types. Remove dead batteries immediately to prevent
acid from leaking into the battery compartment. Dispose of
them in accordance with instructions on page 59 of this
manual. Warning: batteries must not be exposed to excessive
heat such as sunshine, fire or the like.
The performance of the remote control will deteriorate
beyond a distance of five metres or outside an angle of 30
degrees from the centre of the television. If the operating
range becomes reduced, the batteries may need replacing.
Inserting batteries and effective range of
the remote
8
CONNECTING YOUR TV
Connecting external equipment
Before connecting any external equipment, turn off all main power switches. If there is no switch,
remove the mains plug from the wall socket.
Aerial cables: - - - - - - - - - - - - - - - - - - - - - - -
Connect the aerial to the socket on the rear of the television.
If you use a decoder* and/or a media recorder, it is essential
that the aerial cable is connected through the decoder and/
or through the media recorder to the television.
SCART leads: . . . . . . . . . . . . . . . . . . . . . . . .
Connect the video recorder IN/OUT socket to the television.
Connect the decoder TV socket to the television. Connect the
media recorder SAT socket to the decoder MEDIA REC.
socket.
Before running Auto Tuning, put your decoder and media
recorder to Standby.
The phono sockets alongside the COMPONENT VIDEO
INPUT sockets will accept L and R audio signals.
The Digital Audio Output socket enables the connection of a
suitable surround sound system. NOTE: this output is always
active.
HDMI™ (High-Definition Multimedia Interface) is for use with
a DVD decoder or electrical equipment with digital audio and
video output.
For acceptable video or PC signal formats through the HDMI
terminals, see page 61.
NOTE: Although this television is able to connect to HDMI
equipment, it is possible that some equipment may not
operate correctly.
LAN port is used to connect the TV to your home network.
A wide variety of external equipment can be connected to
the back of the television; therefore, the relevant owner’s
manuals for all additional equipment must be referred to
for exact instructions.
We recommend SCART 1 for a decoder and SCART 2 for a
media recorder.
If connecting S-VIDEO equipment, set the INPUT for EXT 2.
See page 49.
If the television automatically switches over to monitor
external equipment, return to normal television by pressing
the desired programme position button. To recall external
equipment, press
o to select between DTV, EXT 1, EXT 2,
EXT 3, HDMI 1, HDMI 2, HDMI 3, HDMI 4, PC or ATV.
When the external input mode is selected while viewing DTV
mode, the SCART socket does not output video/audio
signals. The SCART output will also be muted in EPG mode.
COMPONENT VIDEO INPUT (EXT 3)
HDMI™ INPUT
SOCKETS
SCART 2 (EXT 2)
FIXING STRAP
SCART 1 (EXT 1)
decoder*
media recorder
*a decoder could
be Digital Satellite or
any other compatible
decoder.
POWER switch
OPTICAL DIGITAL AUDIO OUTPUT
Illustration represents 46SV685D.
Antenna/Cable
LAN port
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are registered
trademarks of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
INSTAPORT™ and INSTAPORT logo are trademarks of Silicon Image,
Inc. in the United States and other countries.
9
CONNECTING YOUR TV
Connecting an HDMI
™
or DVI
device to the HDMI input
The HDMI input on your television receives digital
audio and uncompressed digital video from an
HDMI source device or uncompressed digital
video from a DVI (Digital Visual Interface) source
device.
This input is designed to accept HDCP (High-Bandwidth
Digital-Content Protection) programme material in digital
form from EIA/CEA-861-D–compliant
[1]
consumer
electronic devices (such as a set-top box or DVD player with
HDMI or DVI output). For acceptable video signal formats,
see page 61.
NOTE:
• Some early HDMI equipment may not work properly with
your latest HDMI TV, due to the adoption of a new
standard. Please unplug your HDMI cable first and then try
setting the following options (Lip Sync, INSTAPORT™) to
“Off”. Your early HDMI source should operate properly
with your television. See page 50.
• Supported Audio format: Linear PCM, sampling rate 32/
44.1/48kHz.
Connect an HDMI cable (type A connector) to the HDMI
terminal.
For proper operation, it is recommended that you use an
HDMI cable with the HDMI Logo ( ).
• If your HDMI connection is capable of 1080p and/or your
television is capable of refresh rates greater than 50Hz, you
will need a Category 2 cable. Conventional HDMI/DVI
cable may not work properly with this mode.
• HDMI cable transfers both video and audio. Separate
analogue audio cables are not required (see illustration).
• See “HDMI 1 Audio” on page 50.
The HDMI 4 terminal is located on the side of the television.
To view the HDMI device video, press the
o button to select
HDMI 1, HDMI 2, HDMI 3 or HDMI 4 mode.
Connect an HDMI-to-DVI adapter cable (HDMI type A
connector) to the HDMI 1 terminal and audio cables to the
PC/HDMI1 (AUDIO) socket (see illustration).
• The recommended HDMI-to-DVI adapter cable length is
6.6 ft (2m).
• An HDMI-to-DVI adapter cable transfers video only.
Separate analogue audio cables are required.
• See “HDMI 1 Audio” on page 50.
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is
recommended that you follow these procedures:
• When turning on your electronic components, turn on the
television first, and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device first, and then the television.
To connect an HDMI device
HDMI
OUT
VIDEO AUDIO
LR
R
L
OUT
IN
HDMI cable
HDMI device
To connect a DVI device
DVI/HDCP
OUT
VIDEO AUDIO
LR
R
L
OUT
IN
HDMI-to- DVI
adapter Cable
Audio cable for HDMI
to television connection
(not supplied)
DVI device
[1] EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of high-definition
video signals. Because this is an evolving technology, it is possible that
some devices may not operate properly with the television.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
10
CONNECTING YOUR TV
REGZA-LINK connection
You can control the basic functions of connected audio/video devices using the television’s remote control
if you connect a REGZA-LINK compatible AV amplifier or playback device. For an explanation of setup
and operations, see pages 51–52.
For the setup shown above, you will need three HDMI cables
(see page 9).
NOTE:
• If several devices are connected, the REGZA-LINK feature
may not operate properly.
• For proper operation, it is recommended that you use HDMI
cables with the HDMI Logo ( )
• The HDMI 4 terminal is located at the side of the television.
• This function is available with one PC and one AV
amplifier.
This function is available when one PC and one AV
amplifier are connected separately. However, it may not
operate properly if the PC is connected via the AV
amplifier.
Before controlling the device(s):
• After completing the above connections, set the REGZA-
LINK Setup menu as you desire (see page 51).
• The connected devices must also be set. For details, see the
operation manual for each device.
• The REGZA-LINK feature uses CEC technology as regulated
by the HDMI standard.
• This feature is limited to models incorporating Toshiba’s
REGZA-LINK. However, Toshiba is not liable for those
operations. Refer to individual instruction manuals for
compatibility information.
VIDEO
AUDIO
LR
R
L
OUT
IN
HDMI
OUTHDMI
IN
HDMI
OUT
VIDEO
AUDIO
LR
R
L
OUT
IN
HDMI
OUT
VIDEO
AUDIO
LR
R
L
OUT
IN
AV amplifier
Playback device
Playback device
11
CONNECTING YOUR TV
Connecting a computer
With either an RGB/PC or an HDMI connection,
you can watch your computer’s display on the
television and hear the sound from the television’s
speakers.
When connecting a PC to the RGB/PC terminal on the
television, use an analogue RGB (15-pin) computer cable and
a PC audio cable for the PC/HDMI1 (AUDIO) socket. Select
PC from the PC/HDMI 1 Audio options in the AV Connection
menu located in the SETUP menu.
To use a PC, set the monitor output resolution on the PC
before connecting it to the television. For acceptable PC
signal formats, see page 60.
To display the optimum picture, use the PC setting feature (see
page 48).
NOTE:
• The PC audio input terminal on the television is shared with
the HDMI 1 analogue audio input terminal (see page 50).
• Some PC models cannot be connected to this television.
• An adapter is not needed for computers with a compatible
mini D-sub15-pin terminal.
• Depending on the DVD’s title and the specifications of the
PC on which you are playing the DVD-Video, some scenes
may be skipped or you may not be able to pause during
multi-angle scenes.
• A band may appear at the edges of the screen or parts of
the picture may be obscured. This is due to scaling of the
picture by the set, it is not a malfunction.
• When PC input mode is selected, some of the television’s
features will be unavailable e.g. Manual Settings in the
SETUP menu, Colour, Tint, Sharpness and Black/White
Level in the PICTURE menu.
• If connecting a certain PC model with a unique PC signal,
the PC signal may not be detected correctly.
When connecting a PC to the HDMI terminal on the television,
use an HDMI-to-DVI adapter cable and an analogue audio
cable.
If connecting a PC with an HDMI terminal, use an HDMI cable
(type A connector). A separate analogue cable is not
necessary (see page 9).
For acceptable PC and video signal formats, see page 61.
NOTE:
• The edges of the images may be hidden.
• If connecting a certain PC model with a unique PC signal,
the PC signal may not be detected correctly.
To connect a PC to the RGB/PC terminal
the back of your television
Computer
Audio cable for PC to
television connection
(not supplied)
Conversion adaptor if
required (not supplied)
Mini D-sub 15 pin
connector
RGB PC cable
(not supplied)
To connect a PC to the HDMI terminal
the back of your television
Computer
Audio cable
for PC to
television
connection
(not supplied)
HDMI-to-DVI
adapter cable
12
CONNECTING YOUR TV
Connecting a home network
The LAN port allows your Toshiba TV to connect to
your home network. You can use this revolutionary
home entertainment networking system to access
photo, video and audio files that are stored on a
DLNA server and play/display them on your TV.
For supported formats, see page 36.
Installing the ULCS application
In order for your TV to play files stored on a PC, if you do not
have the DLNA server you can do with your PC which is
installed ULCS application (supplied). ULCS is software that
allows files to be shared between playback equipment and a
home network, or between two or more PCs.
Install the ULCS software Limited Edition (supplied). To
operate the PC as a DLNA server, follow the instructions in the
installation manual on the CD-ROM.
The software on the supplied CD is a Limited Edition without
any customer support. For more information and to upgrade
it to a full professional version please visit:
http://www.transtechnology.co.jp/products/soft/ucs/
NOTE:
• The TV’s home network feature is compatible with
Microsoft
®
Windows
®
XP/Vista.
• The TV’s home network connection allows access to file
sharing only. You will NOT be able to use the TV to access
the Internet.
• If you use a hub or switch to connect the TV to your home
network, you may not be able to use the automatic setup
and have to manually set up the network address. See
page 53.
• If you use a router with built-in DHCP functionality, use the
automatic setup. Manual setup may not work.
• If you connect the TV and PC directly, use Ethernet
crossover cable.
Microsoft and Windows are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other.
To connect the TV to a home network
the back of your television
Cable or
Phone jack
[2]
[2]
[2][3]
[2]
[1]
Modem (DSL or Cable)
Router with Hub
Server PC
PC
[1] Coaxial or telephone cable (depending on your modem type)
[2] Standard LAN cable
[3] Do NOT connect a phone jack directly to the TV's LAN port.
13
CONNECTING YOUR TV
Controls and input connections
A wide variety of external equipment can be connected to the input sockets on the side of the television.
Whilst all the necessary adjustments and controls for the television are made using the remote control, the
buttons on the television may be used for some functions.
If the RED LED is unlit, check that the mains plug is connected
to the power supply and press the
! (POWER) button on the
left side of the television to switch the television on. If the
picture does not appear, press
1 on the remote control. It
may take a few moments. The GREEN LED will be lit.
To put the television into Standby, press
1 on the remote
control. To view the television, press
1 again. The picture
may take a few seconds to appear.
Press MENU on the remote control to display the menu.
The menu appears as a list of five topics. As each symbol is
selected by pressing
C or c on the navigation ring on the
remote control, its respective options will appear below.
NOTE: The same menu is displayed in DTV (Digital TV) and
ATV (Analogue TV) modes; however, some items are greyed
out in each case.
To operate the menu, press
B and b on the remote control
to move up and down and press
C or c to select your desired
setting. Follow the on-screen instructions. The functions of
each menu are described in detail throughout the manual.
To alter the volume press –
2 +.
To alter the programme position press
b p B.
Press MENU and
I, i, U or u to control the sound and picture
options.
Press MENU to finish.
An S-video cable provides better picture performance than a
composite video cable. If you connect an S-Video cable to
EXT 3, be sure to disconnect the standard (composite) video
cable or the picture performance will be unacceptable.
Media Player feature provides access to photos, movies or
music files stored on a USB storage device, SD memory card
(for photos only) or networked server PC connected via the
LAN port.
To select an external input, press
o until the appropriate
input source is selected as described on page 49.
Please always refer to the owner’s manual of the equipment
to be connected for full details.
NOTE: Interactive video games that involve shooting a "gun"
at an on-screen target may not work with this TV.
Standby
RED LED – Standby
GREEN LED – Power on
ORANGE LED - Programme
timer set (digital only)
RED LED – Programme timer
Active (digital only)
POWER switch
COMMON INTERFACE
The Common Interface is for
a Conditional Access Module
(CAM).
Contact a service provider.
USB port
To access
photo, movies
or music files
HDMI 4 INPUT
INPUT 3
(EXT 3)
Input 3 (side) will
take priority over
EXT 3 (back) if both
connections are used
at the same time.
GREEN LED – On Timer set
Illustration represents 46SV685D.
SD card slot
To access photo files
Switching on
Using the remote control
Using the controls and connections
• DivX
®
is a registered trademark of DivX, Inc., and is used under
license.
• SD Logo is a trademark
14
SETTING UP YOUR TV
Startup Application
Before switching on the television, put your
decoder and media recorder, if applicable, to
Standby.
To set up the television, use the buttons on the
remote control as detailed on page 6.
a Press the 1 button. The Quick Setup screen will
appear. This screen will appear the first time that the
television is switched on and each time Reset TV is
selected.
b Highlight Menu Language and press C or c to select
the menu language.
c Press b to highlight Country and C or c to select.
The television is now set up to tune the stations for the
selected country.
NOTE:
•The following display menus will differ slightly
according to the country you selected.
•If there is not a country that you want to select in the
list or you want to view DTV programmes but DTV
is not selectable, select Others.
d Press Q, and the Location screen will appear.
e Press C or c to select Home or Store. For normal
home use, select Home (skip step 6).
f Press Q. If Store is selected in step 5, the Auto Demo
screen will appear. Press
C or c to select On to use
the demo.
g Press Q. If the Ant/Cable In screen appears, press
C or c to select Antenna or Cable.
h Press Q, and the Auto Tuning start up screen will
appear with the option to select between DTV and
ATV, DTV or ATV if available. Use
C or c to select
the appropriate mode.
i Press b or B to highlight Start Scan, and then press
Q.
NOTE: If Cable is selected in step 7, additional setting
options appear in the Auto Tuning screen. See “Ant/
Cable In“ section.
The television will start to search for available DTV
and/or ATV channels. The progress bar will indicate
the scan status.
You must allow the television to complete the
search.
When the search is complete, the television will
automatically select position one.
The Auto Tuning screen will display the total number
of services found.
j Press C or c to view the DTV (digital channel) or ATV
(analogue channel) lists.
k Use b or B to move through the list to select a
channel, and then press
Q to view.
In ATV mode, some areas may receive duplicate
stations. There may not be a clear picture or the
signal may be weak, so the station order can be
changed using ATV Manual Tuning.
REMEMBER: Press ATV/DTV at any time to select
between ATV and DTV (DTV TV/DTV RADIO/DTV
TEXT if available) modes.
NOTE: The time will be set automatically by
transmission but can be advanced or decreased by
using Local Time Setting in the DTV Settings screen.
Quick Setup
Quick Setup
Country UK
Primary Subtitle Language
English
English
English
English
Secondary Subtitle Language
Primary Audio Language
Secondary Audio Language
Menu Language English
Location
Home
To use the TV for displaying in a store showroom, please
select [Store]. [Home] mode is recommended for normal
use.
Ant/Cable In
Antenna
Auto Tuning
DTV and ATVTuning Mode
Start Scan
Auto Tuning
Progress Found
ATV Tune Waiting...
Channel: C7
DTV Tune 3% 2
15
SETTING UP YOUR TV
From this menu, you can set the RF input configuration to
cable.
a Press MENU, and select SETUP menu.
b Use b to highlight Ant/Cable In and use C or c to
select Antenna or Cable.
NOTE: When you attempt to change the Ant/Cable In
setting, a warning message will appear followed by
PIN entry (if PIN has been set) and a prompt for Auto
Tuning.
c When Ant/Cable In is set to Cable, the following
setting options will be provided in the Auto Tuning
screen.
Press
B or b to select an item, and then press C or
c to select your desired option.
With the exception of DTV Scan Type and DTV Modulation
items, all of the following items will have 2 operating modes.
The first is Auto where the values for each item are preset by
the system. The second is an Input mode where you will be
able to enter a single value in place of the pre-set value. If no
channel is currently tuned and the Input state is chosen, a
system default value will be shown. However, if a channel is
currently tuned when the item is accessed, the value of the
current channel will be displayed.
DTV Scan Type:
This item determines whether a Quick Scan or a Full Scan will
be executed.
The Quick Scan is a simplified version of the Full Scan that is
designed to complete in less time.
DTV Start Frequency:
This sets the frequency from which the scan will begin.
DTV End Frequency:
This sets the frequency at which the scan will end.
* Valid entry range for frequency items is 113.000-858.00
for C-Book/Other and 114.000-858.00 for Nordig-C. If
numbers outside of this range are entered, the values will
automatically be set to the min. or max. valid value as
appropriate.
DTV Modulation:
You can choose from five QAM modulation settings.
DTV Symbol Rate:
This is the baud rate (KS/s) of the scan.
* Valid entry range for Symbol Rate is 4000-7200. If a
number outside of this range is entered, the value will be
automatically set to the min. or max. valid value as
appropriate.
DTV Network ID:
This is the Network ID to be utilized for the scan. This item is
greyed out when DTV Scan Type is set to “Full Scan”.
* Valid entry range for Network ID is 1-65535. If a number
outside of this range is entered, the value will be
automatically set to the min. or max. valid value as
appropriate.
PLEASE NOTE
The Reset TV menu can also be accessed at any
time from the SETUP menu.
Ant/Cable In (if available)
Auto Tuning
DTV and ATVTuning Mode
DTV
Quick ScanScan Type
AutoStart Frequency
AutoEnd Frequency
AutoModulation
AutoSymbol Rate
AutoNetwork ID
Start Scan
16
SETTING UP YOUR TV
NOTE: As new services are broadcast, it will be necessary to
re-tune the television in order to view them.
Auto Tuning will completely re-tune the television and can be
used to update the channel list. It is recommended that Auto
Tuning is run periodically to ensure that all new services are
added. All current channels and settings, i.e. locked
channels, will be lost.
a Press MENU and use C or c to select SETUP menu.
Use
b to highlight Auto Tuning. Press Q.
b A screen will appear warning that previous
programmes and settings will be deleted.
Use
C or c to select DTV and ATV, DTV or ATV, if
available, then highlight Start Scan and press
Q to
continue with the Auto Tuning.
NOTE: If you have selected "Others" for the Country
field in the SETUP menu, and select a tuning mode
other than "DTV" , choose the optimum ATV
broadcasting system (B/G, I, D/K or L).
The television will start to search for all available DTV
and/or ATV services.
You must allow the television to complete the
search.
When the search is complete, the Auto Tuning screen
will display the services found.
c Use b or B to move through the list to select a
channel, and then press
Q to view.
ATV Manual Tuning
The television can be tuned-in manually using ATV Manual
Tuning. For example, you might use the feature if the
television cannot be connected to a media recorder/decoder
with a SCART lead or when you want to tune-in a station on
another System.
Use
C and c to move across the screen and select any of the
ATV Manual Tuning options. Then use
B or b to adjust the
settings.
1 Position:
The number to be pressed on the remote control to tune
the channel.
2 System:
Specific to certain areas.
3 Colour System:
Factory set to Auto, should only be changed if problems
are experienced, i.e. NTSC input from external source.
4 Skip:
Set Skip to On (
8) or Off (() for the selected channel.
See page 18
5 Signal Class:
The channel classification.
6 Channel:
The channel number on which a station is being
broadcast.
7 Search:
Search up and down for a signal.
8 Manual Fine Tuning:
Only used if interference/weak signal is experienced.
See page 56.
9 Station:
Station identification. Use the
B or b and C or c buttons
to enter up to seven characters.
To allocate a position on the television for a decoder and
media recorder: turn the decoder on, insert a pre-recorded
film in the media recorder, press PLAY, and then manually
tune.
Auto Tuning
SETUP
Menu Language English
Country
Ant/Cable In
Auto Tuning
ATV Manual Tuning
DTV Settings
DTV Manual Tuning
UK
Antenna
AV Connection
Auto Tuning
DTV and ATVTuning Mode
Start Scan
Previous settings will be lost!
Press EXIT for no change.
Tuning
ATV Manual Tuning
System: I
1 A C 2 0 V C R
I
123 4 65 7 8 9
17
SETTING UP YOUR TV
a Press MENU and using C or c select the SETUP menu.
With
b highlight ATV Manual Tuning and press Q
to select.
b Use B or b to highlight the desired position. We
suggest Pos. 0 for a media recorder.
c Press Q to select. If the channel chosen for the media
recorder is set to skip, Skip should be removed before
storing.
d Press c to select System and use B or b to change
if required.
e Then press c to select Search.
f Press B or b to begin the search. The search symbol
will flash.
g Each signal will show on the television. If it is not your
media recorder, press
B or b again to restart the
search.
h When your media recorder signal is found, press c
to move along to Station. With
B, b, C and c put
in the required characters, e.g. VCR.
i Press Q to save.
j Repeat for each position you want to tune, or press
RETURN to return to the list of channels and select the
next number to tune.
k Press EXIT when you have finished.
l To name external equipment, e.g. DVD on EXT 2,
press
o to select o2, then select Manual Settings
from the SETUP menu.
m Press c to select Label then using B, b, C and c put
in the required characters, and then press
Q to save.
Different Channel numbers may be displayed.
SETUP
Menu Language English
Country
Ant/Cable In
Auto Tuning
ATV Manual Tuning
DTV Settings
DTV Manual Tuning
Germany
Antenna
AV Connection
Pos. Channel Station
ATV Manual Tuning
1
2
3
4
6
7
8
C2
C7
S10
S40
C22
5
C25
C28
C30
ATV Manual Tuning
System: I
1 A C 2 0
I
ATV Manual Tuning
Search:
1 C 2 0 IA
PLEASE NOTE
This television has direct channel entry if the
channel numbers are known.
Select the ATV Manual Tuning screen in Step 3.
Enter the Position number, the System, then C for
standard (terrestrial) channels or S for cable
channels and the Channel number. Press Q to
save.
ATV Manual Tuning
Station: VCR
1 A C 2 0 V C R I
Manual Settings
Label: DVD
EXT 2 A D V D
18
SETTING UP YOUR TV
To prevent certain channels from being viewed, positions can
be skipped.
a Select ATV Manual Tuning from the SETUP menu.
b Use B or b to highlight the position to be skipped
and press
Q to select.
c Press c to select Skip.
d Use B or b to turn Skip on.
Press
Q.
8 on the screen indicates a skipped position.
e Press RETURN and repeat from Step 2 or press EXIT.
Each position has to be individually selected. To turn
Skip off, repeat the procedure for each position.
Skipped positions cannot be selected by P
U and Pu
or by the controls on the television but can still be
accessed by the number buttons on the remote
control.
Channels may be moved and saved to the position of your
choice.
a Select ATV Manual Tuning from the SETUP menu.
b With the list of channels showing, use B or b to
highlight the channel you want to move and press
c.
c Use B or b to move through the list to your preferred
position. As you do so, the other channels will move
to make room.
d Press C to save your move.
Repeat as necessary, and then press EXIT.
Skip
Pos. Channel Station
ATV Manual Tuning
1
2
3
4
6
7
8
C2
C7
S10
S40 ABC1
ABC1C22
5
C25
C28
C30
ATV Manual Tuning
Skip: On
1 A C 2 0 I
Sorting positions
Pos. Channel Station
ATV Manual Tuning
2
3
4
5
6
7
8
S10
C7
C40
C22
1
C2
C25
C28
C30
ABC1
ABC1
19
SETTING UP YOUR TV
DTV Manual Tuning
NOTE: This feature varies depending on the Ant/Cable In
setting.
This feature is available for service engineers or can be
used for direct channel entry if the multiplex channel
is known.
a Select DTV Manual Tuning from the SETUP menu and
press
Q.
b Enter the multiplex number using the number buttons
or use
C or c to adjust the number up or down.
c Highlight Start Scan, and then press Q. The
television will automatically search for that multiplex.
When the multiplex is found, any channels that are
not currently in the channel list will be added and the
channel information at the top of the screen will be
updated.
d Repeat as necessary. Press EXIT to finish.
When Ant/Cable In is set to Cable, DTV Manual Tuning items
are as follows:
Frequency – input a specific frequency to be scanned
Modulation – choose from one of five QAM modulation
options
Symbol Rate – input a specific baud rate (KS/s) to be used
for the manual scan
DTV Settings
The channel order may be changed to suit your personal
preference.
a Select DTV Settings from the SETUP menu and press
Q.
b Select Channels and press Q.
c With the list of channels showing, use b or B to
highlight the channel you want to move and press
c.
d Use b or B to move through the list to your preferred
position. As you do so, the other channels will move
to make room.
e Press C to save your move. Repeat as necessary, then
press EXIT.
To renumber for the highlighted channel, press the
RED button on the remote control.
Manual Tuning
Manual Tuning for DVB-C
DTV Manual Tuning
WEAK
Signal Strength
Quality
Channel
GOOD 85%
76%
Start Scan
STRONGAVERAGE
13
Pos.New TypeName
ABC ONE
0 New Channels - Total 6
ABC TWO
ABC THREE
ABC NEWS 24
DTV Manual Tuning
2
1
7
40
ABCi
51
Channels
DTV Settings
Channels
Subtitle and Audio
Channel Options
PIN Setting
Parental Control
Auto Channel Update
DVB Character Set
Local Time Setting
Off
11:51
Standard
Pos. Name
ABC ONE
ABC TWO
ABC THREE
CABC Channel
TV
Channels
2
1
7
30
ABC NEWS 24
40
51
ABCi
20
SETTING UP YOUR TV
Edit the channel number using the number buttons
and press
Q.
If the Auto Channel Update is set to On, when the TV is in
standby mode, Digital Tuning is automatically executed and
any new channels are saved.
a Select DTV Settings from the SETUP menu and press
Q.
b Press b to select Auto Channel Update and use C or
c to select On.
This feature allows you to manually set the character set
(Standard = Table 0, West = Table 5 or Latin alphabet 9)
to be used for DVB-C or DVB-T channels.
a Select DTV Settings from the SETUP menu and press
Q.
b Press b to select DVB Character Set and use C or c
to select Standard, West or Latin alphabet 9.
If the broadcast information has changed in your DVB-T
receiving area, the TV screen will display the message
“Broadcast information has changed. Would you like to
rescan now?” please follow the message.
a Select DTV Settings from the SETUP menu and press
Q.
b Press b to select Dynamic Scan and use C or c to
select On.
You can select either Home or Store mode. Home is
recommended for normal home use. Select Store when using
the television for displaying in a shop, etc.
a Select Location from the SETUP menu.
b Press C or c to select Home or Store.
This is a digital television which is integrated to allow the use
of both digital and analogue services. However, during the
lifetime of this set it is very likely that analogue services will
be switched off to allow for more new digital services.
This ‘switch-off’ will happen in a number of phases, which will
be advertised in your area well in advance. It is
recommended that at each phase the television is re-tuned to
ensure that existing and new digital services can be viewed
without disruption.
Auto Channel Update
DVB Character Set
Dynamic Scan
Pos. Name
ABC ONE
ABC TWO
ABC THREE
CABC Channel
TV
Channels
2
1
7
30
ABC NEWS 24
40
ABCi
5- - -
Location setting
Analogue switch-off
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
