Contec BCS-0611 Owner's manual

BCS-0611 1

PCI Backplane with 6-Slots

(PCI x 1, ISA x 2, PCI/ISA x 1)

BCS-0611 User's Manual

CONTEC CO., LTD.

Description

This product is a backplane supporting a PCI bus compatible SBC (CPU board).

It has one PCI (for SBC) bus slot (2-slot wide), one PCI bus slot, one PCI/ISA shared bus slot, and two

ISA bus slots.

Package Contents

- The BCS-0611 Backplane Board

- This User's Manual

- ATX Control 6pin Cable

- IPC Precaution List

- Serial number label

Features

- 1 PCI (SBC) + 1 PCI + 1 PCI /ISA + 2 ISA slots

- PCI-ISA bridge is on board.

- Compact PCI/ISA shared systems can be built.

- Support for ATX compliant power supply.

- The optional chassis suitable for mounting.

Supported SBC (CPU) board

- SPC-8520-LV

- SPC-8521-LV

BCS-0611 User's Manual

2 BCS-0611

Specifications

Item

Specification

Correspondence bus

PCI Bus *1, ISA Bus

Number of slots SBC(CPU board) PCI bus slot (CN1) x 1 *1

PCI bus slot (PCI2) x 1

PCI/ISA shared bus slot (PCI1, ISA3) x 1 *2

ISA bus slot (ISA1, ISA2) x 2

Board size (mm) *3

ISA board : 163(L), PCI board : 177(L)

Supply power

+5VDC, -5VDC, +12VDC, -12VDC, +3.3VDC(only for ATX power supply)

Operating conditions

0 - 60°C, 10 - 90% RH (No condensation)

Storage conditions

-20 - 70°C

Floating dust particles

Not to be excessive

Corrosive gases

None

Major dimensions (mm)

129(W) x 200(D)

Weight

220 g

Installable chassis

FA-UNIT-M6BE

*1 The SBC(CPU board) must install it to the CPU slot(CN1).

*2 PCI1/ISA3 slot is a shared slot. Only one of the boards, ISA or PCI, can be mounted. They cannot be used at the

same time.

*3 Some boards can’t be mounted for the shape.

BCS-0611 User's Manual

BCS-0611 3

Board Dimension

1

29

16.5

40.5

10.2

154.9

25.4

200

6

.4

39.4

6

2

0

.3

2

0

.3

1

4

.3

20

.

3

4

0

.6

8-

φ4

102

8.3

29.9

PC

I2

CN

1

PCI

1

IS

A

3

I

SA

2I

S

A1

P

W1

JP

1

23

CN2

CN3

F

AN1

FAN2

BC

S-0

611

PWRCTL

PWRBTN

C

O

N

T

EC

[

mm]

BCS-0611 User's Manual

4 BCS-0611

Jumper Setting and Connectors

ATX Power Supply Connector: PW1

When used with an ATX-compliant power supply that supports remote power on/off, the CPU card can

turn off the system power through software control.

To enable soft-off control in software, advanced power management must be enabled in the Setup

program and in the operation system.

Pin No

.

1

2

3

4

5

6

7

8

9

10

Function

+

3.3

V

-12

V

GND

PON

GND

G

ND

GND

-5V

+

5V

+5

V

Pi

n N

o.

11

12

13

1

4

1

5

16

17

18

1

9

20

Fun

cti

on

+3.3V

+

3.3V

GN

D

+5

V

GND

+5V

GND

Po

wer

Go

od

+5VSBY

+1

2V

Suitable Housing : 39-0

1-22

00

(co

rrep

ond

)

Suitable Con

tac

t

: 5

556

(c

orre

spo

nd)

Mak

er :

Mol

ex

P

W1

1

1 1

20 1

0

System FAN Connector: FAN1 / FAN2

FAN1 and FAN2 are 3-pins header for the system cooling fan power connector. The fan must be a 12V

fan. Pin 2 is for +12V power supply.

1

2

3

FAN1 / FAN2

P

in

N

o

.

1

2

3

F

un

c

ti

on

GN

D

+1

2V

N

.C.

S

uit

abl

e Ho

usi

ng :

22

-01-

1034

(c

orre

spo

nd)

Sui

tabl

e COn

tac

t :

08-7

0-0

057

(co

rre

spon

d)

M

aker

: M

ole

x

ATX Power Control Connector: CN2(PWRCTL)

Pin No.

1

2

3

4

5

6

F

unct

ion

PME#

GN

D

PBTN-IN

GN

D

PSO

UT

+5V SB

Y

C

N2

1

2

3

4

5

6

Sui

table Housing:

XHP

-6 (

cor

res

pond)

Sui

tabl

e C

ont

act : SXH-001T-P

0.6

(co

rre

spo

nd)

Maker :

JST

BCS-0611 User's Manual

BCS-0611 5

ATX Power Button connector: CN3(PWRBTN)

Pin No.

1

2

Function

PBTN

GND

Suitable Housing : XHP-2 (correspond)

Suitable Contact : SXH-001T-P0.6 (conrrespond)

Maker : JST

CN3

21

ATX Power ON: JP1

2-3 Short : Disable ATX power control and set the

ATX Power Supply ON always by push

switch

(use as AT Power Supply).(Default))

1- 2 Short : Enable ATX Power Control by push

switch

Pin No.

1

2

3

Function

PSOUT

PBIN

GND

1

2

3

JP1

Connector Block Drawing

1

2

6

5

4

3

2

1

JP1

3 2 1

9 +5VSBY

14 PON

ATX Power Connector

ATX Power ON/OFF Switch

GND

PBTN

+5VSBY : +5V Stanby Voltage supplied to CPU board.

PS_OUT : ATX Power Supply ON (Low Lebel) Signal from CPU board.

GND

PBTN_IN: Output Switch Signal (connected to CN3) to CPU board.

GND

PME# :

PME# signal is input to the CPU board. They are valid

only for the signals compatible with the CPU board

(See the CPU board manual).

[Connect to CPU board with 6pin Cable (included).

]

CN2

CN3

PW1

BCS-0611 User's Manual

6 BCS-0611

Copyright

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this

document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear

in this document nor for results obtained by the user as a result of using this product.

Limited One-Year Warranty

CONTEC products are warranted by CONTEC CO., LTD to be free from defects in material and

workmanship for up to one year from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a copy of the original

invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from

which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and

original boards. The warranty is not applicable if the device has been tampered with or damaged

through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in

which case repairs will be considered beyond the warranty policy.

BCS-0611 User's Manual

BCS-0611 7

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you

purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor

be liable for any incidental or consequential damages due to such defect or consequences that arise from

inexperienced usage, misuse, or malfunction of this device.

BCS-0611 User's Manual

BCS-0611

User’s Manual

CONTEC CO.,LTD. June 2015 Edition

3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan

Japanese http://www.contec.co.jp/

English http://www.contec.com/

Chinese http://www.contec.com.cn/

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD. [02242006]

[02242006] Management No. A-51-226

[06262015_rev3] Parts No. LYGA143

Contec BCS-0611 Owner's manual

Contec BCS-0611 Owner's manual

Related papers

Other documents