Contec BCS-0611 Owner's manual
- Category
- Interface cards/adapters
- Type
- Owner's manual
BCS-0611 1
PCI Backplane with 6-Slots
(PCI x 1, ISA x 2, PCI/ISA x 1)
BCS-0611 User's Manual
CONTEC CO., LTD.
Description
This product is a backplane supporting a PCI bus compatible SBC (CPU board).
It has one PCI (for SBC) bus slot (2-slot wide), one PCI bus slot, one PCI/ISA shared bus slot, and two
ISA bus slots.
Package Contents
- The BCS-0611 Backplane Board
- This User's Manual
- ATX Control 6pin Cable
- IPC Precaution List
- Serial number label
Features
- 1 PCI (SBC) + 1 PCI + 1 PCI /ISA + 2 ISA slots
- PCI-ISA bridge is on board.
- Compact PCI/ISA shared systems can be built.
- Support for ATX compliant power supply.
- The optional chassis suitable for mounting.
Supported SBC (CPU) board
- SPC-8520-LV
- SPC-8521-LV
BCS-0611 User's Manual
2 BCS-0611
Specifications
Item
Specification
Correspondence bus
PCI Bus *1, ISA Bus
Number of slots SBC(CPU board) PCI bus slot (CN1) x 1 *1
PCI bus slot (PCI2) x 1
PCI/ISA shared bus slot (PCI1, ISA3) x 1 *2
ISA bus slot (ISA1, ISA2) x 2
Board size (mm) *3
ISA board : 163(L), PCI board : 177(L)
Supply power
+5VDC, -5VDC, +12VDC, -12VDC, +3.3VDC(only for ATX power supply)
Operating conditions
0 - 60°C, 10 - 90% RH (No condensation)
Storage conditions
-20 - 70°C
Floating dust particles
Not to be excessive
Corrosive gases
None
Major dimensions (mm)
129(W) x 200(D)
Weight
220 g
Installable chassis
FA-UNIT-M6BE
*1 The SBC(CPU board) must install it to the CPU slot(CN1).
*2 PCI1/ISA3 slot is a shared slot. Only one of the boards, ISA or PCI, can be mounted. They cannot be used at the
same time.
*3 Some boards can’t be mounted for the shape.
BCS-0611 User's Manual
BCS-0611 3
Board Dimension
1
29
16.5
40.5
10.2
154.9
25.4
200
6
.4
39.4
6
6
2
0
.3
2
0
.3
1
4
.3
20
.
3
4
0
.6
8-
φ4
102
8.3
29.9
PC
I2
CN
1
PCI
1
IS
A
3
I
SA
2I
S
A1
P
W1
JP
1
1
23
CN2
CN3
F
AN1
FAN2
BC
S-0
611
PWRCTL
PWRBTN
C
O
N
T
EC
[
mm]
BCS-0611 User's Manual
4 BCS-0611
Jumper Setting and Connectors
ATX Power Supply Connector: PW1
When used with an ATX-compliant power supply that supports remote power on/off, the CPU card can
turn off the system power through software control.
To enable soft-off control in software, advanced power management must be enabled in the Setup
program and in the operation system.
Pin No
.
1
2
3
4
5
6
7
8
9
10
Function
+
3.3
V
-12
V
GND
PON
GND
G
ND
GND
-5V
+
5V
+5
V
Pi
n N
o.
11
12
13
1
4
1
5
16
17
18
1
9
20
Fun
cti
on
+3.3V
+
3.3V
GN
D
+5
V
GND
+5V
GND
Po
wer
Go
od
+5VSBY
+1
2V
Suitable Housing : 39-0
1-22
00
(co
rrep
ond
)
Suitable Con
tac
t
: 5
556
(c
orre
spo
nd)
Mak
er :
Mol
ex
P
W1
1
1 1
20 1
0
System FAN Connector: FAN1 / FAN2
FAN1 and FAN2 are 3-pins header for the system cooling fan power connector. The fan must be a 12V
fan. Pin 2 is for +12V power supply.
1
2
3
FAN1 / FAN2
P
in
N
o
.
1
2
3
F
un
c
ti
on
GN
D
+1
2V
N
.C.
S
uit
abl
e Ho
usi
ng :
22
-01-
1034
(c
orre
spo
nd)
Sui
tabl
e COn
tac
t :
08-7
0-0
057
(co
rre
spon
d)
M
aker
: M
ole
x
ATX Power Control Connector: CN2(PWRCTL)
Pin No.
1
2
3
4
5
6
F
unct
ion
PME#
GN
D
PBTN-IN
GN
D
PSO
UT
+5V SB
Y
C
N2
1
2
3
4
5
6
Sui
table Housing:
XHP
-6 (
cor
res
pond)
Sui
tabl
e C
ont
act : SXH-001T-P
0.6
(co
rre
spo
nd)
Maker :
JST
BCS-0611 User's Manual
BCS-0611 5
ATX Power Button connector: CN3(PWRBTN)
Pin No.
1
2
Function
PBTN
GND
Suitable Housing : XHP-2 (correspond)
Suitable Contact : SXH-001T-P0.6 (conrrespond)
Maker : JST
CN3
21
ATX Power ON: JP1
2-3 Short : Disable ATX power control and set the
ATX Power Supply ON always by push
switch
(use as AT Power Supply).(Default))
1- 2 Short : Enable ATX Power Control by push
switch
Pin No.
1
2
3
Function
PSOUT
PBIN
GND
1
2
3
JP1
Connector Block Drawing
1
2
6
5
4
3
2
1
JP1
3 2 1
9 +5VSBY
14 PON
ATX Power Connector
ATX Power ON/OFF Switch
GND
PBTN
+5VSBY : +5V Stanby Voltage supplied to CPU board.
PS_OUT : ATX Power Supply ON (Low Lebel) Signal from CPU board.
GND
PBTN_IN: Output Switch Signal (connected to CN3) to CPU board.
GND
PME# :
PME# signal is input to the CPU board. They are valid
only for the signals compatible with the CPU board
(See the CPU board manual).
[Connect to CPU board with 6pin Cable (included).
]
CN2
CN3
PW1
BCS-0611 User's Manual
6 BCS-0611
Copyright
Copyright 2006 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear
in this document nor for results obtained by the user as a result of using this product.
Limited One-Year Warranty
CONTEC products are warranted by CONTEC CO., LTD to be free from defects in material and
workmanship for up to one year from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the original
invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from
which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original boards. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
BCS-0611 User's Manual
BCS-0611 7
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
BCS-0611 User's Manual
BCS-0611
User’s Manual
CONTEC CO.,LTD. June 2015 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD. [02242006]
[02242006] Management No. A-51-226
[06262015_rev3] Parts No. LYGA143
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Contec BCS-0611 Owner's manual
- Category
- Interface cards/adapters
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec FA-UNIT-M6BE Owner's manual
-
-
-
-
-
-
-
-
-
Contec BPM-1111 Owner's manual