MBRP S47034CF Installation guide

Type
Installation guide

MBRP S47034CF is a high-quality performance exhaust system designed to enhance the power, sound, and driving experience of your vehicle. It features a durable stainless steel construction and is easy to install, with all necessary hardware included. The system is compatible with a wide range of vehicles and is backed by a limited lifetime warranty.

MBRP S47034CF is a high-quality performance exhaust system designed to enhance the power, sound, and driving experience of your vehicle. It features a durable stainless steel construction and is easy to install, with all necessary hardware included. The system is compatible with a wide range of vehicles and is backed by a limited lifetime warranty.

S4703 © 01/22 PAGE 2 OF 3
Figure 1
Removal of Stock System
1. Apply penetrating lubricant liberally to all exhaust fasteners, hangers and
rubber insulators.
2. Remove the two nuts securing the factory muffler assembly. Remove the
rubber insulators from the vehicle and remove the muffler assembly
3. Remove the nuts that connect the stock down pipe to the front pipe
assembly. Keep the nuts for installation. Remove the stock front pipe
assembly.
Refer to Figure 1.
4. Remove the hangers from the rubber insulators and remove the exhaust from
the vehicle.
5. Remove the exhaust bezel assembly from the rear fascia.
Refer to Figure 2.
Installation of MBRP Performance Exhaust
1. Using the factory nuts removed in Step 3 and the provided 7/16” Flat
Washers, loosely attach the Front Pipe onto the catalytic converter. Ensure
there is some tension on the factory catalytic converter isolator throughout the
installation and alignment process.
Refer to Figure 3.
2. Using two 2.5” Clamps, loosely install the Muffler.
Refer to Figure 4.
3. Loosely install the Mid-Pipe into the factory rubber isolator and into the
Muffler. It may be necessary to remove the rubber isolator from the vehicle,
install it onto the Mid-Pipe hanger, and then back onto the vehicle mount.
Refer to Figure 5.
4. Using a 2.5” Clamp, loosely install the Over-Axle Pipe onto the Mid-
Pipe. Do not install the rubber insulator until the Tail Pipe Assembly is in
position.
Refer to Figure 6.
Figure 2
Figure 3
Figure 4
Figure 5
S4703 © 01/22 PAGE 3 OF 3
Figure 6
Figure 7
Figure 8
Figure 9
5. Apply penetrating lubricant to the factory muffler isolators and install
onto the Tail Pipe Assembly.
Refer to Figure 7.
6. Using a 2.5” Clamp, loosely install the Tail Pipe Assembly into the
Over-Axle Pipe and through the fascia, then reattach the factory
isolators to the vehicle.
Refer to Figure 8.
7. Install the Tips onto the Tail Pipe Assembly.
Refer to Figure 9.
8. Go back over the entire system to align for the best clearance everywhere.
Ensure there is some tension on the factory catalytic converter rubber isolator
before fully tightening any clamps. Clearance is very limited at the trunk floor
weld seam above the Tail Pipe Assembly. The seam can be bent to allow
extra clearance if desired.
9. Align the edge of each band clamp with the edge of the joint it is connecting.
Tighten all hardware and clamps, starting at the front and working rearward to
secure the system. Check along the full length of the exhaust system to ensure
there is adequate clearance for fuel lines, vent lines, brake lines, frame, bodywork,
suspension, and any wiring, etc. If there is any interference detected, relocate, or
adjust to provide adequate clearance. Ensure all clamp connections are secure and
components are unable to rotate or slide. Band clamps require approximately 45
lb-ft (60 N-m) of torque. Verify clearances, system security and band clamp
torque after 30-60 miles (50-100 km) of driving.
Congratulations! You are ready to begin experiencing the improved power,
sound and driving experience of your MBRP Performance Exhaust.
We know you will enjoy your purchase!
  • Page 1 1
  • Page 2 2
  • Page 3 3

MBRP S47034CF Installation guide

Type
Installation guide

MBRP S47034CF is a high-quality performance exhaust system designed to enhance the power, sound, and driving experience of your vehicle. It features a durable stainless steel construction and is easy to install, with all necessary hardware included. The system is compatible with a wide range of vehicles and is backed by a limited lifetime warranty.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI