Kenmore Elite 23354363200 Owner's manual

Brand: Kenmore Elite

Model: 23354363200

Category: Cooker hoods

Type: Owner's manual

Kenmore Elite 23354363200 is a range hood designed for domestic cooking. It features three fan speeds, two halogen bulbs, and aluminum grease filters that can be cleaned in a dishwasher. The range hood can be used in both ducted and non-ducted configurations. In a ducted configuration, it can be connected to 6-inch round ductwork. In a non-ducted configuration, it can be used with a charcoal filter (purchased separately) to recirculate air. The range hood also has a decorative flue that can be removed for cleaning.

E L ! T E

an e

Use & Care /Installation Manual

Campana

Manual de uso y cuidado /instalaci6n

Models 233.54363200 (90 cm wide/90 cm de ancho)

Modelos

¢0

Sears, Roebuck and Co, Hoffman Estates, IL 60179 U.S.A. www.sears.com

Read and save these instructions .............................. 2

Table of contents ......................................................... 2

Warranty ...................................................................... 2

Safety instructions ....................................................... 3

Operation .................................................................... 4

Cleaning ..................................................................... 4

Parts included with hood ............................................. 5

Tools needed for hood installation .............................. 5

Parts not included with hood ....................................... 5

Equivaient duct length chart ........................................ 6

[nsta[I the ductwork ..................................................... 7

Install mounting bracket .............................................. 7

[nsta!t the hood ........................................................... 7

[nstalI Electrical Hate .................................................. 8

Connect Wiring ........................................................... 8

Connect ductwork ducted configuration only ............... 9

Connect ductwork (Nomducted configuration only)... 10

Service parts .............................................................. 11

Service parts ............................................................. 12

Ifwithin 1 year from the date of installation, any part of

this range hood fails to function properly due to a defect

in material or workmanship, Sears wilI repair the part

or furnish and install a new part, free of charge.

FULL 30_DAYWARRANTY ON FiNiSH ON PAINTED OR

BRIGHT METAL PARTS

If within 30 days from the date of instaIlation, the finish

on any painted or bright metal parts of this range hood

is defective in material or workmanship, Sears wit!

furnish and install a new part, free of charge.

WARRANTY SERWCE ISAVAILABLE BY CONTACTmNG

THE NEAREST SEARS SEVmCECENTERfDEPARTMENT

mNTHE UNITEDSTATES.

This warranty applies only while this product is in use

in the United States. This warranty gives you specific

legal rights and you may have other rights which vary

from state to state.

Sears, Roebuck and Co., Dept 817WA, Roffman

Estates, IL 60179

READANDSAVETHESE[NSTRUCT[ONS

mNTENDED FOR DOMESTmC COOKING ONLY ,_,

WARNING _

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOW_

JNG:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power off at

service paneI and lock service panel to prevent power

from being switched on accidentally. When the

service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as

a tag, to the service panel.

3. hsta!lation work and electrical wiring must be done

by a qualified person(s) in accordance with all

applicable codes and standards, including fire-rated

construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting.

Foltow the heating equipment manufacturer's

guidelines and safety standards such as those

published by the National Fire Protection Association

(NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any solid-state speed

controi device.

8. To reduce the risk of fire, use onIy steet ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE

FIRE:

.A Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or

medium settings.

B. Atways turn hood ON when cooking at high heat or

when cooking flaming foods (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe').

C. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware

appropriate for the size of the surface element.

WARNING _

TO REDUCE THE RiSK OF INJURY TO PERSONS IN

THE EVENT OF A RANGE TOP GREASE FIRE, OB_

SERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie

sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do not

go out immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be

burned.

3. DO NOT USE WATER, including wet dishcloths or

towels _violent steam explosion will result.

4. Use an extinguisher ONLY if:

A You know you have a Class ABC extinguisher and

you already know how to operate it.

B. The fire is small and contained in the area where

it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on "Kitchen Fire Safety Tips" published by

NFPA.

CAUTION &

1. To reduce risk of fire and to properly exhaust air, be

sure to duct air outside. Do not vent exhaust air into --

spaces within waits or ceilings or into attics, crawl

spaces, or garages.

2. Take care when using cleaning agents or detergents. _'_

3. Avoid using food products that produce flames under

the Range Hood.

4. For general ventilating use only. Do not use to _,-,

exhaust hazardous or explosive materials and

vapors.

5. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

6. Your hood motor has a thermal overload which will

automatically shut off the motor if it becomes _'_

overheated. The motor will restart when it cools

down. Ifthe motor continues to shut off and restart,

have the hood serviced. _,

7. For best capture of cooking impurities, the bottom of "_

the hood should be a minimum of 24" and a ,,_

maximum of 30" above the cooking surface.

8. Two installers are recommended because of the

large size and weight of this hood.

9. Please read specification labet on product for further --

information and requirements.

CONTROLS:

LOW SPEED &

MOTOR "ONoOFF"

BUTTON

LIGHT /

BUTTON

N®

MEDIUM

SPEED

BUTTON

0/1 .,, o

HIGH SPEED

BUTTON

MOTOR "ON_

OFF" LIGHT

Press (0/1) Button to turn fan ON to Low speed and to

turn fan OFF.

Press (_ _ ) Button to increase fan speed to Medium.

Press ( ,_,_,_ ) Button to increase fan speed to High.

HALOGENBULBS

WARNING: To reduce the risk of emectric shock,

disconnect hood from power supply before

changing bulbs.

BULB

WARNING: To reduce the risk of etectdc

shock, disconnect from power suppty before

cleaning.

Grease filters

Clean frequently using hot water and a mild detergent or

in your dishwasher. The aluminum mesh filters should

be washed approximately every month depending on the

amount of usage. Wash more often if your cooking style

generates greater grease - like frying foods or wok

cooking.

Nomducted charcoam filters

(available separately _ see page 5)

Clear filter surfaces frequently with a damp cloth and a

mild detergent. DO NOT immerse filters in water or put in

dishwasher.

This range hood requires two halogen bulbs (Type T4,

12V, 20W).

To change bulbs:

1. Insert a flat-blade screwdriver into one of the slots

on the bulb ring and gently pry ring and glass lens off.

2. Remove the bulb by pulling sideward (DO NOT

ROTATE). CAUTION: BULB MAY BE HOT!

3. Replace bulb and ring. Do not touch replacement

bulb with bare hands!

FUSE REPLACEMENT

WARNING: To reduce the risk of electric

shock, disconnect from power supply before

replacing fuse.

Stainless steel hood surfaces

Stainless steel hoods should be washed regularly with a

clear cloth, warm water and mild soap or dish detergent.

Clean in the direction of the polish line& Rinse weII with

clear water and wipe dry immediately. You may wish to

apply light oil used for furniture polishing to emphasize

it's bright finish.

DECORATIVE

FLUE

Remove the decorative flue.

Open the fuse box.

Replace with the same type of fuse (5x20mm, 4A, 125V).

6-inchRoundDamper

DECORATmVEFLUE

8 MOUNTmNGSCREWS

(4,8 x 38ram Pan Head)

Screwdriver

(Flat & PMHips)

Aluminum Grease Filter

(1 each hood)

MOUNTING BRACKET

FLUEMOUNTING BRACKET

6 MOUNTING SCREWS

(3,9 x 9,Smm Pan Head)

8 DRYWALL ANCHORS

PenciJ

OPTmONAL PARTS (purchase separately)

Charcoam

Filter

Flange

Air Baffle

2 Mounting

_'C_ screws

(3,4 x 15ram

Pan Head)

Non=Ducted Kit

-- Sears Part

No. 58113

Flue

m Extension

Kit for

10 ft ceiling

Sears Part

No. 58112

"Parts Not hciuded With Hood" available by ceiling ]

Sears at 1-80O-4-MY-HOM E® J

Tape Wire Stripper

Measure

F,'

DriH Sabre Saw =or= Keyhome Saw Duct Tape

Kenmorerangehoodsaredesignedtoperformefficientlywhenattachedtolongrunsofduct.Asapointofreference,

thishoodwillfunctionatapproximately80%ofitsratedairftowwhen75equivalentfeetof6"roundductworkis

attached.Usethischarttocalculatetheequivalentductlengthofyoursystem.

Broan Model 401

Straight Duct

3¼qn. × lOqn. x 2-ft. long

Equivalent length

2ft°

Broan Model 406

Straight Duct

6qn, round × 2-ft. long

Equivalent length

2ft°

Broaa Mode_ 419

6qn. Round Elbow

Equivalent length

8ft°

Brans Mode_ 412R

3¼qn. × lOqn. to

6-in. Round

Transition

Equivalent length

5.5 ft.

8roan Model 428

3¼qn. x lOqn.

Right-angle Elbow

Equivalent length

8.5 ft.

Brash ModeB 429

31/_qn. x lO-in.

Right-angle F_at

EBbow

Equivalent length

24ft°

8roan }_,_ode_430

3%=in. × lO=in.

Right=angle

Short

Eave Elbow

Equivalent length

15fL

8roan Model 431

3Y4=in.× lO=in.

Right-angle

Long

Eave Eibow

Equivalent tength

15fL

Sears Mode_ 59691

64n, Round

Wall Cap

Equivalent length

34ft°

(6-ft. w/o damper)

Sears Model

59391

3¼-in. x

lO-in.

WaR Cap

Equivalent length

45ft°

(7-ft. wio damper)

Sears

Mode_ 59091

Roof Cap

(accepts 7-in. round

or 3%-in. x lOqa. duct)

Equivalent length

30 ft, (7tit. w/o damper;

Sears Model "Ducting Accessories" available by caring:

Sears at 1-800-4-MY-HOME ®

Broan Model "Ducting Accessories" available by caring:

Sears at 1-800-558-1711

NOTE:Toreducetheriskoffire,useonlymeta_

ductwork.

1. Decidewheretheductworkwillrunbetweenthehood

andtheoutside.

2. Astraight,shortductrunwiltallowthehoodtoperform

mostefficiently.

3. Longductruns,elbows,andtransitionswilIreduce

theperformanceofthehood.Useasfewofthemas

possible.Largerductingmayberequiredforbest

performancewithlongerductruns.

4. Installarooforwallcap.Connectroundmetat

ductworktocapandworkbacktowardshood

location.Useducttapetosea!thejointsbetween

ductworksections.

1. Constructwoodwal!framingthatisflushwithinterior

surfaceofwal!studs.

Makesure:

a) theframingiscenteredoverinstallationIocation.

b) theheightoftheframingwillallowthemounting

brackettobesecuredtotheframingwithinthe

dimensionsshown.

2. After wall surface is finished, secure mounting

bracket to framing using dimensions shown.

ROOF CAP \

ROUND DUCT

WALL

CAP

ROUND

ELBOW

24"T0 30"ABOVE

COOKING SURFACE 6"

ADAPTER

FRAMING BEHIND DRYWALL

36-3]16" :in;hit3 i_ ,1ii1 24* R_!_ bil_;qlg

42-3][6'_' _in;ql_ i0 ,1ii'1 30* _:_'q t_ll_nl_

Hang the hood from the bracket through the

rectangular cut-out on the back of the hood. Cut=out

is larger than the bracket to allow for horizontal

adjustment.

The bottom of the hood should be 24" to 30" above

the cooking surface.

Attach hood height /angle adjustment screws to

hood bracket. Use these screws to level the hood.

Secure the hood with mounting screws. Use drywall

anchors, provided, if wal! studs or framing are not

available.

MOUNTING .......

SCREWS

HOOD

HEIGHT/ANGLE

ADJUSTMENT

MOUNTING

SCREWS

WALL FRA_'_ING

CUTOUT

Mount the electrical plate to the hood with 2 screws.

Note: This range hood must be properly grounded. The

unit should be installed by aqualified electrician in

accordance with aiI applicable nationam and tocam

emectricamcodes.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an

eiectrica! short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric

current. This appliance is equipped with a cord having a

grounding wire with a grounding plug. The ptug must be

plugged into an outlet that is property installed and

grounded.

WARNING =Improper grounding can result in a risk of

electric shock.

Consult a qualified electrician if the grounding

instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is

too short, have a qualified electrician install an outlet near

the appliance.

Set the etectrica! power supply within the space covered

by the decorative flues.

Position the power socket at a maximum distance of 33=

7/16" (85 cm) from where the lead exits from the hood

(see illustration alongside). Make sure this does not

interfere with the bracket fastening area or with the

decorative flue (where the flue touches the wall).

Fit the plug into the power socket.

Adjustthewidthofthefluemountingbracket

assemblytoequaltheinsidewidthofdecorativeflue.

Insertandtightenmountingscrewstoholdbracket

width.

Usemountingscrewsandwallanchorstosecure

fluemountingbrackettotheceiIingasshown.

FLUE MOUNTING

BRACKET ASSEMBLY

MOUNTING

SCREWS

WALL

ANCHORS

MOUNTING

\!} SCREWS

3. Use 6" round damper /duct connector to 6" discharge n,,a

on hood.

4. Attach 6" round metal duct to connect the duct coIlar :::$

on the hood to the ductwork above. ,_

5. Use duct tape to make at! joints secure and air tight.

6. hsert the decorative flues setting them on the hood. __

7. Extend the upper flue to the ceiling and secure with

two mounting screws.

DECORATIVE

j_ FLUE

BUCTTAPE

6" ROUND

_/_I_METALDUCT

LOUVERS ON

FLUE

(Slide down,

inside of lower

flue)

¢)

Adjust the width of the flue mounting bracket

assembly to equat the inside width of decorative flue.

Insert and tighten mounting screws to hold bracket

width.

FLUE MOUNTING

BRACKET MOUNTBNG SCREWS

2. Use mounting screws and wall anchors to secure

flue mounting bracket assembly to the ceiling as

shown.

MOUNTBNG

SCREWS

3. Measure the distance from the top of the hood outlet

to the ceiling o and add 6 inches.

4. Cut a piece of 5" round flexible metallic duct (not

included) to the length determined in Step 3. Attach

flange to bottom of flexible duct and secure with duct

tape.

5. Attach top of flexible duct to air baffle and secure with

duct tape.

6. Connect the flange to the hood outlet.

7. Turn upper flue section upside down so air vents

are at the top. Slide upper flue section into tower flue

section.

8. Set flue assembly on hood, with top tilted away from

wall. Align (4) holes in baffle with (4) holes in top flue

section.

9. Attach baffle to upper flue section with (4) screws

(included). Use a short screwdriver.

10. Extend the upper flue section to the ceiling and

secure to upper bracket with (2) mounting screws.

AIR VENTS

UPPER

FLUE SECTION

MODEL 54363

KEY NO. PART NO. DESCRIPTmON

58**

113

114

118

119

120

122"*

145

146

147

151

154

165

2O8

223

228

229

230

234

240

274

332

4O7

474

477

998

B08087137

B02300233

BE3348354

B03295005

B02300891

BW0000019

B02310203

B03295076

B03202007

B03295018

B02300249

B08091462

BE3347000

B02005029

B08088378

BE3344720

B0320245!

B03292499

BE3344123

BE3344!24

B08091367

B08088369

B032920170

B032920180

BR2300132

B032920200

B03202286

B03295008

B02300783

B03200351

B08086240

B03201014

B03292303

B03292302

B03292301

B03295035

B03295009

BE3344985

B02300798

B03295006

B06002013

B0808!0501

B03300488

B02300782

B02300674

Grease Filter

Motor Capacitor

Electrical Box Support

Terminal Box

Halogen Lamp Bulb

Blower

Motor

Blower Wheel

Rubber Washe

Discarge Collar

Feeder Cable

Blower Mounting Cover

Filter Support

Glass Visor

6" Round Damper

Switch Mounting Bracket

Nameplate

Clip

Decorative Flue Bottom

Decorative FtueTop

Flue Mounting Bracket

Air Baffle

Feeder cable connection Box

Feeder Cable Connection Box Cover

Junction Clamp

Electrical Box Wires Stop

Grommet

Control Board Box

Transformer

Switch Button

Controls Board

Warning lamp

Switch Board Box Cover

Control Board Box

Button Actuator(4)

Motor Capacitor Box

Cover

Blower Support Bracket

Hatogen Lamp Housing

Terminal Cover

Blower Assembly dncludes Key Nos. 45, 48,

49, 53)

Mounting Hardware Package

Nomducted recircutation filter

Fuse

Fuse holder

* Not shown assembled.

** Parts included in Non-Ducted Kit

MODEL 54363

208

165

477

145

146

274

023O0674

02300782

1t4

23O

228

240

223

229

234

B03300488

151

147

332

122"*

120

11g

118

407

474

113

154

Leayconserveestasinstrucciones...........................14

Tabladecontenido...................................................14

Garantia....................................................................14

Instruccionesdeseguridad.......................................15

Funcionamiento........................................................16

Limpieza...................................................................16

Piezasinctuidasconiacampana..............................17

HerramientasnecesariasparalaInstalaci6ndela

campana...................................................................17

Piezasnoincluidasconlacampana*.......................17

CuadrodetargoequivaIentedeconducto................18

Instalaci6nde!tubodeextraccion.............................19

Instalaci6nsoportedemontaje.................................19

Instalaci6ndeIacampana........................................19

Instalaci6ndetaptaca..............................................20

Instalaci6net6ctrica...................................................20

Entubadodecanalizaci6n(Configuraci6ncontubo)21

Entubadodecana!izaci6n(Configuraci6nsintubo).22

Lista de piezas de recambio ..................................... 23

Lista de piezas de recambio ..................................... 24

Si dentro de 1 a_o de Ia fecha de Ia instaiaci6n,

cuatquier parte de esta campana de cocina deja de

funcionar en forma apropiada debido a defecto en e!

material o la marco de obra, Sears reparara ta pieza

afectada o proveer_, e instalara una pieza nueva libre

de cargo.

GARANTIA COMPLETA DE 30 BiAS EN ELACABADO

EN PIEZAS METALICAS PINTADAS O ABRULLANTADAS

Si dentro de 30 dias de la fecha de la instaiaci6n, e!

acabado de cuaiquier parte metbJica pintada o

abrillantada perteneciente a esta campana de cocina

aparece con defecto en e! material o Ia mano de obra,

Sears proveer_, e instalar&, una pieza nueva iibre de

cargo.

EL SERVlCIO DE GARANTBASE OBTIENE PONIENDOSE

EN CONTACTO CON EL CENTRO DESERVlCIO O

DEPARTAMENTO SEARS MAS CERCANO EN LOS

ESTADOS UNIDOS.

Esta garant[a es valedera unicamente si este producto

se tiene en uso dentro de Ios Estados Unidos. Esta

garantia Ie confiere derechos legates especificos y Ud.

puede tener ademb.s otros derechos que varian de

estado a estado.

Sears, Roebuck and Co., Dept. 817WA, Hoffman

Estates, IL 60179

LEA Y CONSERVE ESTAS INSTRUCC!ONES

,,& INDICADO PARA EL USO EN COClNAS DOMESTiCAS

ADVERTENCIA _, ,_,

PARA EVITAR EL RIESGO DE INCENDIO,

CORTOCIRCUITO O DANO PARA LAS PERSONAS,

OBSERVE ATENTAMENTE LAS SIGUIENTES

NORMAS:

1. Use esta unidad solamente de Ia manera indicada

por et fabricante; si tiene dudas, pOngase en

contacto con este a Ia direcciOn o telefono indicados

en ta garantia.

2. Antes de hacer una revision o de limpiar la unidad,

desconectela de la red para evitar que se encienda

de manera accidental. En el caso de que este no

pueda ser desacti-vado, se indicar_, en la ptaca de

caracte-risticas.

3. El montaje y la instaIaciOn electrica debe hacerlos un

tecnico especializado siguiendo Ias normas

est&.ndar e incluyendo aque!Ias de construcciOn anti

incendio.

4. Necesita aire suficiente para una apropiada

combustion y escape de gases a traves de! tubo de!

depOsito de quema de combustible. Para evitar que

el humo aspirado vuetva a la cocina, siga Ias

directivas det fabricante y tas normas estandar de

siguridad asi como Ias normas pubticadas pot Ia

AsociaciOn de prevenciOn de incendios (NFPA) y la

Socie-dad americana de especialistas en cateo

facciOn, refrigeraciOn y aire acondicionado y ademas

Ias normas de las autoridades locales.

5. Hacer un corte o un taladro en Ia pared o en et techo

no debe danar la instalaciOn electrica u otras

instalaciones ocultas en la pared.

6. Los conductos ventiladores deben siempre

desalojar a! exterior.

7. No use esta unidad con dispositivo de controi de la

vetocidad a estado sOlido.

8. Para evitar el riesgo de incendio, use solamente

conductos de metal.

9. Esta unidad tiene que ser conectada a tierra.

PARA EVITAR EL RIESGO DE FUEGO POR ALTO

NIVEL DE GRASA:

A Nunca abandone los quemadores con e! fuego alto.

La cocciOn causa humo y restos de grasa que

pueden arder. Catiente el aceite a fuego medio o

bajo.

B. Encienda siempre la campana cuando cocine a

fuego alto o cuando cocine alimentos facilmente

infiamabIes (por ejemplo Crepes Suzette, Cerezas

Jubilee, Ternera flambeada con granos de pimienta).

C. Limpie con frecuencia los ventiIadores. No se debe

acumuIar grasa en el ventitador o en el filtro.

D. Usa e! tamanp de cazueta apropiado. Use siempre

utensilios de cocina de tamafio y material

adecuados.

ADVERTENCIA ,_ Z_

PARA EVITAR EL RIESG© DE DANOS A PERSONAS

EN CASO DE FUEGO POR ALTO N[VEL DE GRASA,

TENGA EN CUENTA LO SIGUIENTE:*

1. Sofoque Ia llama con una tapadera apropiada, una

bandeja metb_Iica6 un utensilio de cocina que pueda

cubrirla, despues, apague e! quemador. Act0e con

precaucion para evitar quema-duras. Si la llama no

se extingue inmedia-tamente, salga y Ilame a los

bombe-ros.

2. Nunca coja una sarten en llamas, porque corre et

riesgo de quemarse.

3. NO USE AGUA ni pa_os o toallas h0midas porque

puede provocarse una violenta humareda.

4. Use un extintor solamente si:

A. Posee un extintor de clase ABC y sabe

perfectamente cOmo usarlo.

B. El fuego es peque_o y esta controIado en e!

mismo sitio en que empez6.

C. Ha Itamado con anterioridad a los bomberos.

D. Puede combatir et fuego retroced[endo hacia Ia

satida.

* Basado en "Seguridad antifuego en la codna"

pubticado pot NFPA.

1. Para reducir el riesgo de incendios y para evacuar

correctamente los humos, asegurarse de haber

realizado una conducciOn de! aire hasta e! exterior.

No expulsar los humos en espacios cerrados por

paredes o techos, _,ticos, espacios angostos o

garajes.

2. Prestar la m_.xima atenciOn a! utilizar productos de __

limpieza o detergentes. "_

3. Evitar et uso de productos atimentarios que puedan _"

infiamarse bajo la campana. "_

4. SOIo para ventilaci6n total. No use gases de escape

peligrosos o materiaIes y vapores explosives.

5. Para evitar daF_osen e! funcionamiento de! motor e

imputsores ruidosos y/o desequi-tibrados,

mantenga alejados de la unidad de encendido

pulverizadores en seco o polvo.

6. Et motor tiene un niveI de sobrecarga termica que

apaga autom_.ticamente et motor cuando se ha

recalentado excesivamente_ El motor se pone de

nuevo en fincionamento cuando Ia temperatura baja.

Si el motor comienza a encenderse y a apagarse, _'

debera, hacer una revision de este. _b

7. Para limpiar mejor Ias impurezas al cocinar, Ia _:

distancia entre Ia parte inferior de la campana y Ia :_

zona de cocciOn debe set minimo 24" omaximo 30".

8. Debido a su gran tamano y peso, se recomienda su

montaje por parte de dos tecnicos esperializados.

9. Se recomienda leer la placa de caracte-risticas de!

producto para ulterior informaciOn. ¢'b

Mand0s:

BOTON

LLE

BOTON

VELOCIDAD

LENTA & MOTOR

"ON-OFF"

BOTON

VELOCIDAD

RAPIDA

BOTON

VELOCIDAD

MEDIA

/LUZ MOTOR

"ON-OFF"

011 oo oo_

Pulse el bot6n (0/1) para encender el ventilador a velocidad

lenta y para apagar el ventilador.

Pulse el bot6n ( _- ) para aumentar la velocidad del ventilador

a media.

Pulse el bot6n (---) para aumentar la velocidad del

ventilador a alta.

LAMPARAS HALOGENAS

ADVERTENCIA: Para redacir el riesgo de

una descarga el_ctrica, desconecte el

suministro el_ctrico antes de limpiar ta

unidad.

ADVERTENCIA: Para reducir el riesgo de una

descarga el_ctrica, desconecte el suministro

em_ctrico antes de limpiar la unidad.

Filtros de malla de aluminio

Limpie frecuentemente tos filtros con agua caliente y un

detergente suave. Los fiItros se pueden lavar en

lavaplatos. Se debe Iavar los filtros de matla de atuminio

aproximadamente cada mes, dependiendo de su uso.

Lb.velos con mayor frecuencia si su forma de cocinar

genera m#.s grasa =como, pot ejemp!o, frituras o 'wok'.

FmLTRO8 ANTIGRASA

Filtros sin conducto

(disponibtes por separado =vet pagina 5)

Limpie frecuentemente Ias superficies de los fittros con

un paso h0medo y un detergente suave. NO sumerja los

filtros en agua ni los coioque en et Iavaplatos.

ASRAZADERA

Este tipo de campana necesita dos (2) lamparas

hat6genas (Tipo T4, 12V, 20W).

Para cambiar Ias lamparas:

1. DestornilIar la abrazadera en sentido antihorario.

2. Extraiga ta I#.mpara oblicuamente. NO LA GIRE.

Atenci6n: Ins I_mparas pueden estar caHentes.

3. Sustituir con lamparas de! mismo tipo (T4, 12V, 20W).

No toque la Iampara de repuesto con Ins manos

desnudas.

SUSTITUCION FUSIBLE

ADVERTENCIA: Para redacir el riesgo de

una descarga el_ctrica, desconecte el

suministro el_ctrico antes de limpiar ta

unidad.

Superficies de acero inoxidable de la campana

Se debe Iavar las campanas de acero inoxidable

peri6dicamente con un pafio limpio, agua tibia y unjab6n o

detergente para ptatossuave. Limpielas en Iadirecci6n de Ins

linens deputido. Enjuaguelas bien con agua Iimpia y sequela

de inmediato con un paNo. Podraapticartes un aceite Ieve

utilizado para Iustrar muebtes para reatzar suacabado

Iustroso.

Remover e! tubo decorativo. Abrir Ia caja fusible.

Sustituir por un fusible deI mismo tipo (5x20mm, 4A,

125V).

Reguladordetiro

redondo

de6'pulgadas

TUBODECORATmVO

8TORNtLLOS DE

MONTAJE (4,8 x 38ram

cabeza redonda)

Filtro de grasa de alumioio

(1 pot campana)

SOPORTE DE

_,_ONTAJE

SOPORTE PARA EL

MONTAJE DELTUBO

6TORNILLOS DE MONTAJE

(3,9 × 9,Smm cabeza

redonda)

8ESCARPmAS

PIEZAS OPTATWAS (compra separada)

Filtros ai

carbon

Adaptador

Defector de

aire

4Tornillos de

montaje

(3,4 × 15ram

cabeza redonda)

-- Kit Filtrante

Sears

Cod.N.58113

Kit del tubo

-- decorativo

10' Pulgadas

Sears

Cod. N. 58112

Las "Piezas no incluidas con la campana" est&n

disponibles Hamaodo a Sears a_1-800-4-_,_Y-HO_,_E®

Destornillador

(chato y Phillips)

Perforadora

L_piz

Sierra de punta

Cinta Pelador de cable

m_trica

-o- Serrucho de punta Cinta adhesiva

para conductos

LascampanasdecocinaKenmorefuerondisefiadasparssudesempefioeficientecuandoseIassujetaalargos

recorridosdeconducto.Comopuntodereferencia,estacampanafuncionaraaaproximadamenteel80%desuflujo

deairenominalcuandoseIesujeta61m(200pies)equivalentesdecenductoredondode17.8cm(7").Utiliceesta

cuadroparscalculare!largoequivalentedeconductodesusistema.

Broan Modelo 401

Conducto recto

31/4-pulg. × 1O-pulg. × 2-pies de largo

Largo equivalente

0°61 m (2 pies)

Broan _odelo 408

Conducto recto

8-pulg, alrededor × 2 pies de largo

Largo equivalente

0°61 m (2 pies)

8-in. Round Elbow

Equivalent length

8ft°

Modelo Sears 59581

31/4-pulg. × 1O-pulg.

a 8-pulg,

TransiciTn redondo

Largo equivalente

1,7 m (5,5 pies)

Broan Modelo 412H

31/4=pulg. x 10=pulg.

s 8-pulg,

TransiciTn redondo

Largo equivalente

1,7 m (5,5 pies)

Broan Modelo 428

3¼=pulg. x 1O=pulg.

Aeodado con _ngul(

a la derecha

Largo equivalente

2.6 m (8.5 pies)

Broan Modelo 429

3%=pulg. × 1O=pulg.

Acodado piano con

_ngulo a la derecha

Largo equivafente

7.3 m (24 pies)

Modeto Sears 59691

8-pulg. Tap6n de

pared redondo

Largo equivalente

10 m (34 pies)

(1.8 m [6-pies] sin

regutador de tire)

Modelo Sears

59391

31/4=pulg. x

1O=pulg,

TapTn de pared

Largo equivalente

14 m (45 pies)

(2.1 m [7-pies] sin

Modelo

Sears 59091

TapTn de techo

(scepts ducto de

7-pulg. redondo o

de 3%=pulg. x 10-

pulg.)

Largo equivalente

9.1 rn (30 pies)

(2.! m [7-pies] sin

regutador de tire)

Modelo Sears "Accesorios pars conductos" est_e disponibles ltamando:

Sears al 1=800-4-MY-HOME ®

Modelo Broan "Accesorios pars conductoe" est_n disponiblee Hamando:

1o800o558ol 711

NOTA:paraevitarelriesgodehcendio,usesolamente

materiNdemetal.

1. Decidaderidevaacoiocare!tubodeextracci6nentre

Iacampanaylaparteexterior.

2. Unrecorridodetubocortoyrectopermitiraala

campanafuncionardemaneramaseficaz.

3. LosrecorridosIargosdetubo,codesymanguJtos

impidene!buenfuncionamientodeIacampana.Use

etmenornOmerodeelIosposible.Parausos

prolongadosesnecesariountubodeevacuaci6ndel

airedemayordib_metro.

4. Jnstaleunacubierta6unatapa.Unae!tubodemetal

alacubiertayretrocedahastalaposici6ndeIa

campana.UseunecintaparaprecintarIasjuntas

entrelaspartesde!lentubado.

TAPA DE

TECRO

TUBO

DECORATIVO

CAMPANA\

]

24" (61era) A :30" (76¢m)

POR ENCIMA DE LA

ZONA DE COCGION

TUBO

TAPA

PARED

MANGUITO

6"(15cm)

ADAPTADOR

re_,

1. Construya una estructura de madera en Ia pared que

quedara nJveJadacon Ia parte interior de Ios tacos en

Ia pared. AsegOrese de que:

a) La estructura se encuentra centrada por encima

de la instalaci6n de! tubo.

b) La altura de la estructura permite fijar et soporte

de montaje en esta estructura siguJendo Ias

dimensiones indicadas.

2. Una vez que la superficie de la pared este acabada,

sujete el soporte de montaje siguJendo Ias

dimensiones indicadas.

ESTRUCTURA DE MADERA EN LA

/PARED

1. Cueigue la campana det soporte per et agujero

rectangulare situado detrb_sde Ia campana. El

agujero es mas grande que el soporte para permitir

ei ajuste en horizontal.

La parte inferior de la campana debe estar a una

distancia de 24" (61cm) 6 30" (76cm) por encima de

Ia zona de cocci6n.

2. Sujete Ia campana con tornJtlos de montaje. Use

escarpias inctuJdos en e! equipamiento si no

dispone de tacos o de la estructura de soporte en

madera.

TORN_LLOS DE ......

MONTAJE

TORNILLOS DE

REGULATOR DE LA

CAI'_PANA

TORNILLOS

ESTRUCTURA DE MADERA

AGUJERO

RECTANGULARE

Montar la placa de! sistema etectrico fijandola mediante 2

tomittos.

Nota: Este tipo de campana tiene que set conectada a

tierra cuidadosamente. La unidad debe instalarla un

t_cnico electricista siguiendo las normas nacionales y

tocales.

mNSTRUCCUONESDECONEX_6N ATIERRA

Este aparato se debe conectar a tierra_ En case de

cortocircuito, Ia conexi6n a tierra reduce et riego de

eiectrocuci6n ya que posee un hHode descarga a tierra

para la corriente. Este aparato esta equipado con un

cable que posee un hito de toma de tierra con una clavija

de tierra. La ciavija se debe conectar a un enchufe

instalado correctamente y conectado a tierra.

ADVERTENCIA- una cone×i6n a tierra incorrecta puede

provocar desgoa de electrocuci6n.

Consutte a un electricista calificado si no se entienden o

si existe alguna duda sobre Ia correcta conexi6n a tierra.

No utilice un cable de prolongaci6n. Si el cable

proporcionado es demasiado corto, p6ngase en

contacto con un etectricista cafificado para que instale un

enchufe cerca deI aparato.

Conecte Ia alimentaci6n etectrica en et espacio cubierto

pot el tubo decorative.

Coioque ei enchufe a una distancia maxima de 33_7/16"

(85 cm) desde ei cable de la campana (vease figura

adjunta). AsegOrese de que no interfiera con eI b.rea de la

abrazadera de sujeci6n o con e! tubo decorative (donde

et tubo decorativo toca con la pared).

Conecte Ia ciavija a! enchufe.

Page is loading ...

Kenmore Elite 23354363200 Owner's manual

Brand: Kenmore Elite

Model: 23354363200

Category: Cooker hoods

Type: Owner's manual

Download PDF

report

in other languages

español: Kenmore Elite 23354363200 El manual del propietario