PELHAM & WHITE PW82079-W Installation guide

Brand: PELHAM & WHITE

Model: PW82079-W

Type: Installation guide

Owner’s Manual & Installation Guide

Contemporary Tubs

Tub Filler Faucets

Note: Read all instructions before proceeding with installation. All specifications are

subject to change without notice.

Giagni

Warranty

Pelham & White warrants, to the initial consumer purchaser, the surfaces of the bathtub and acrylic plinths to be free of defects in material and

workmanship during normal residential use for a period of 25 years from the date of purchase. This warranty does not cover normal wear and

tear or damage to the surface caused by the use of chemicals that break the structural bonds in the acrylic material (see cleaning & maintenance

page). Damage caused by accident, misuse, or abuse is not covered by this warranty.

If any defects develop under the warranty from the date of purchase, we will, at our discretion, consider repairing or replacing the defective

part(s). Improper use or installation will immediately void the warranty. No other liability or obligation is to be assumed. Proof of purchase (original

sales receipt) must be provided to Pelham & White with all warranty claims. Pelham & White will not be responsible for labor charges and installation

or any other consequential costs. In no event shall the responsibility of Pelham & White exceed the purchase price of the product.

Faucets

Pelham & White faucets come with a limited lifetime warranty. The warranty applies to defects in workmanship and finish. The above warranty does not

apply to damages resulting from shipping, misuse, tampering, abuse or ordinary wear and tear. Warranty for finish is void if proper care is not

demonstrated.

Drains, Feet, Plinths, & Cradles

Pelham & White drains, feet, plinths, cradles, and components are guaranteed to be free from defects in material, workmanship, and finish at the time of

shipment. Should any defects develop within 5 years from the date of purchase, we will, at our discretion, consider repairing or replacing the

defective part(s).

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the

exclusions of limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. For warranty claims

or questions, contact Pelham & White at (855)-561-5222.

In event of a defect

In the event of a defect covered by the limited warranties contained herein, you must notify your authorized Pelham & White representative within 30 days

after the date of the occurrence of the defect, and such representative will repair or otherwise correct the defect within a reasonable time in

accordance with and after subject to the terms and conditions set forth herein. Pelham & White shall not be liable for (a) the cost of shipping or otherwise

transporting parts and materials necessary to correct any defect and (b) any direct, indirect, incidental or consequential damages, (c) all tubs are

thoroughly inspected for defects prior to shipment and a follow up inspection is required after receiving the tub. Thus, the Pelham & White warranty will not

cover the cost associated with the removal and reinstallation of a defective bathtub.

Non-Transferrable

The limited warranties contained herein are not transferable or enforceable by any party other than the original purchases (user).

Transportation & Delivery

The limited warranties contained herein shall not apply to damage or any problem caused by improper handling of the tub to the purchaser or any

subsequent movement of the tub by the purchaser. Purchaser is responsible for all warranty related freight charges.

Property Damage

The limited warranties contained herein shall not cover property damage due to water. The responsibility of water damage is solely that of the

installer or owner as we recommend a pre-install water test in our installation section.

Disclaimer

Authorized Pelham & White representatives are not agents of Pelham & White, and no agent, dealer, or representative, salesperson or other person

is authorized to change, modify, expand or extend the limited warranties contained herein, or to bind Pelham & White or any of its authorized representatives

to be held for injury or damage to any person or property for any claim, regardless of manner in which claims arise.

All measurements are approximations and should be used for reference only. Pelham & White reserves the right to make specification changes without

Before you begin:

•Observe all local plumbing/building codes and ensure flooring support is adequate. Installation of

backflow prevention must comply with local codes and regulations. In certain states models with

handshower must be installed with a listed inline anti-scald device.

• Before you begin work, carefully uncrate and inspect the tub for any damage. If there is a

problem, do not install the tub. Immediately report the problem to the dealer.

• Ensure the floor will support 1200 lbs. (This is the approximate weight of the tub filled with water

and bather.)

• Carefully plan the moving of the bath into the installation area. These bathtubs may not easily fit

through doorways.

• Before installation, ensure proper access to the final plumbing connections.

Safety instructions:

To reduce the risk of injury:

• Do not permit children to use this unit unless they are closely supervised by an adult at all times.

Supervision is also required when the bath is used by an elderly or handicapped individual.

• Use this unit only for its intended use as described in this manual. Do not use attachments not

recommended by the manufacturer.

• Since excessive water temperatures have a high potential for causing fetal damage during

the early months of pregnancy, pregnant or possibly pregnant women should limit bath water

temperatures to 38° C (100° F).

• The use of drugs or alcoholic beverages before or during bath use may lead to unconsciousness

with the possibility of drowning.

• Persons with a medical history of heart disease, low or high blood pressure, circulatory system

problems, or diabetes should consult a physician before using the bath.

• Persons using medication should consult a physician before using the bath since medication may

induce drowsiness while other medication may affect heart rate, blood pressure and circulation.

DANGER: To reduce the risk of injury, enter and exit the bath slowly.

WARNING: Never operate electrical devices in or near the bath. Never drop or insert any object into

any opening within the bath.

To avoid the possibility of personal injury and discoloration of the acrylic surface, the inlet water

temperature should not exceed 60° C (140° F) and the bath should be drained after each use.

FREESTANDING TUB INSTALLATION

Assemble bath on a mat to protect

against damage to bath surface.

● Ensure legs are adjusted in line with the base

of bath.

● Check that bath sits flat; if required

adjust legs to compensate for floor level.

● Place tub in desired location, being sure to

accommodate any plumbing needed for the

faucet and drain. Mark the perimeter of the

tub with a pencil or painter’s tape.

FREESTANDING TUB INSTALLATION SUPPLEMENT

● Install the Brass Tub Drain to the tub. Make the necessary alterations to the floor to accommodate

the tub drain and drain pipe, and enable the drain pipe to be connected to the drainage system as

required by local code.

Use appropriate silicone for surface

type.

● Apply a thick bead of silicone within bath

outline.

● Place tub back in the desired position,

carefully pressing downward to allow the

tub feet to contact the floor and the silicone

to seal the low spots. Clean up the silicone

bead.

Do not touch or ll the tub for 24 hours to let

the silicone fully cure.

5 6

Make the nal connections from the tub drain pipe to the home’s drainage system

per local code.

STEP 5

INSTALLING THE FAUCET

There are three styles and two faucet mounting methods.

Please refer to the appropriate page for your application.

FLOOR MOUNT

see page 7

SINGLE-POST TUBE

see page 11

SINGLE-POST SQUARE

see page 11

WALL MOUNT

see page 9

CONTEMPORARY STYLE

SINGLE-POST FILLER STYLE

CONTEMPORARY FLOOR MOUNT TUB FAUCET

(Allen Wrench)

Step 1- Install #1 spout into

faucet body by pushing straight

down. Align spout facing forward

then tighten with #3 allen screw

(packaged separately with #7 allen

wrench). Do Not Over Tighten.

Step 3- Attach hot and cold risers

C-FRSR to union nuts on back of

faucet body using one #10 rubber

gasket on each riser.

Step 2- Screw #16 handle hub

onto hot/cold cartridges #9 & #17.

Disassemble handle by unscrewing

spokes and install onto cartridge

by securing with screw included.

Reassemble handle.

C-FRSR

Union Nut

C-HLVR

9C-HCRS

Screw

Spokes

Tub

Drain

Washer

C-FB1

C-FRSR

Floor Flange (26)

MIN. 3-3/4"

MAX. 5-1/2"

Decorative

Escutcheon (25)

C-FRSR

Step 4- Drill (2) 1-1/8” holes into floor on 8”

centers for hot and cold water supplies (see

fig. 5 next page). Supply holes should be

drilled at 3 ¾” minimum to 5 ½” maximum

from drain outlet (center to center).

Step 5- Slide #25 decorative escutcheon onto

bottom of risers C-FRSR and push part way

up. Screw #26 floor flange onto threaded

portion of each riser until it stops.

Step 6- Insert risers into hole in floor and

secure floor flanges with appropriate screws/

bolts for your flooring type. (Hardware not

included)

Notes:

1. Faucet is not for use on concrete floors.

2. Please ensure all local plumbing codes are observed during installation

3. Water supply lines must be roughed in on 8” centers.

CONTEMPORARY FLOOR MOUNT TUB FAUCET (cont.)

Step 9- Attach small end of #18 handshower

hose with #30 washer to outlet below diverter

faucet handle.

Step 10- Attach large end of #18 hand shower

hose to #16 handshower with #30 washer and

place in holder.

Step 11- Connect preferred ½” pipe (supplied by

installer) into female threaded riser C-FRSR from

under flooring. Make hot/cold water connections.

Turn on water and check all connections for leaks.

FIGURE 5 Supply line spacing

Step 7- Slide #25 decorative escutcheon down

to cover floor flange.

Step 8- Tighten optional support bracket to

risers and drain

CONTEMPORARY WALL MOUNT TUB FAUCET

(Allen Wrench)

Step 1- Install #1 spout into faucet

body by pushing straight down. Align

spout facing forward then tighten with

#3 allen screw (packaged separately

with #7 allen wrench). Do Not Over

Tighten.

Step 2- Screw #16 handle hub

onto hot/cold cartridges #9 & #17.

Disassemble handle by unscrewing

spokes and install onto cartridge

by securing with screw included.

Reassemble handle.

C-HLVR

9C-HCRS

Screw

Spokes

Notes:

1. Please ensure all local plumbing and building codes are observed when installing

these faucets.

2. Mounting location depends on tub design and location. Be sure to identify tub height

when determining faucet location.

3. There must be a minimum of 2" gap between top of tub rim and bottom of the faucet

spout to comply with plumbing codes.

4. Water supply lines must be roughed in on 8” centers.

CONTEMPORARY WALL MOUNT TUB FAUCET (cont.)

Step 6- Attach small end of #18 handshower

hose with #30 washer to outlet below diverter

faucet handle.

Step 7- Attach large end of #18 hand shower

hose to #16 handshower with #30 washer

and place in holder.

Step 8- Turn on water and check all

connections for leaks.

Finished Wall

Decorative

Flange (28)

Pipe Nipple

C-WLBO (29)

3/8"-1/2"

Washer (10)

C-FB1

Union Nut

Step 3: Rough-in #29 C-WLBO

flush to finished wall. Hot/Cold

supplies should be roughed

in on 8” centers and 1/2” pipe

should extend 3/8” to 1/2”

beyond the finished wall.

Step 4: Screw #28 decorative

flange included with C-WLBO

onto rough portion of #29.

Step 5: Attach faucet to wall by

screwing the union nuts onto the

C-WLBO wall elbows with #10

washers.

Finished Wall

Decorative

Flange

Pipe Nipple

TPN 41 - 2/1

SINGLE CONTROL FREESTANDING TUB FILLER

INSTALLATION GUIDE

Note:

Carefully read this entire installation guide before installing and using this product.

Parts Identication

1. Spout

2. Aerator

3. Faucet Body

4. Diverter Button

5. Main Tube

6. Floor Escutcheon

7. Supply Hoses (2)

8. Floor Bracket

9. Handshower

10. Handshower Hose

MODELS:

PW82424

PW82425

PW82426

MODELS:

PW82427

PW82428

PW82429

345

SINGLE CONTROL FREESTANDING TUB FILLER (CONT.)

FAUCET ASSEMBLY

• Slide the Floor Escutcheon (6) over the

externally threaded end of the Main

Tube (5) as shown.

• Screw the Main Tube (5) onto the Floor

Bracket (8). Hand-tighten as firmly as

possible.

• Feed the Supply Hoses (7)

up through the Main Tube

(5) as shown.

• Thread the HOT supply hose all

the way into the threaded hole

in the bottom of the faucet body

nearest the hand spray holder,

and the COLD supply hose in

the far hole. The connections

on the Faucet Body are also

marked H and C. Hand tighten

or apply light torque with pliers.

No need to overtighten.

• Connect main tube to faucet body

• ROUND BODIES: Screw the Main

Tube (5) onto the Faucet Body (3)

and tighten firmly by hand.

• SQUARE BODIES: Slide the Faucet

Body (3) fully into the end of Main

Tube (5) that has the two setscrews.

Orient the faces of the two pieces so

that the two setscrews are directed to-

ward where the faucet will be viewed

the least. Secure by tightening the

two setscrews. Do not over-tighten.

SINGLE CONTROL FREESTANDING TUB FILLER (CONT.)

MOUNTING FAUCET TO FLOOR

Due to the various materials and conditions that may exist surrounding this installation, it will be the responsibility of

the installer to select the location of the faucet, the appropriate fasteners to secure the faucet to the oor, and the

roughing-in of the supply piping.

Be sure to orient the faucet so that the spout is in the correct direction and at the location that will enable the

spout to ow water into the tub without hitting the rim of the tub.

12 13

• Orient the faucet in correct posi-

tion in relation to the tub.

• Secure the Floor Bracket (8) to

the oor using the appropriate

fasteners.

•Unscrew and remove the Aerator

(2) at the end of the spout.Turn

the faucet o.

• Place Handshower Hose (10) in

an empty bucket and secure.

• Re-install the aerator at the

end of the spout. Be sure

the black rubber washer is

in place. Hand-tighten rmly.

• Slide the Floor Escutcheon (4)

down to the oor and seal with

silicone caulk.

• Connect the Supply Hoses (7)

to the roughed-in hot and cold

piping. Be sure the black rubber

washers are in place. The thread

on the hose swivel nuts is ½ x

14TPI.

TEST & FLUSH

LINES

• Turn on the water supplies.

Check for leaks.

• Turn the faucet on (hot and

cold) and ush the lines of

debris.

• Hold the Handshower

Hose in a bucket, push the

diverter button and ush

that line.

• Connect the Handshower Hose

(10) to the Faucet Body (3). Be

sure the black rubber washer is

in place. Hand-tighten as rmly

as possible. Do not connect the

Handspray yet.

• Connect the Handshower Hose

(8) to the Handshower (7).

• Be sure the black rubber washer

is in place. Hand-tighten rmly.

CLEANING & MAINTAINING YOUR BATHTUB

Cleaning:

 





 

 

   



  



 



NOTE:   

  

 









®  

@  

Contact information

Pelham & White

548 South Columbus Avenue

Mount Vernon, New York 10550

Phone: 855-561-5222

Email: [email protected]

PELHAM & WHITE PW82079-W Installation guide