Outbound GR-C100 User manual
- Category
- Bicycle accessories
- Type
- User manual
Please visit www.outboundsports.com for additional information.
WARNING: Before starting any exercise program. We strongly suggest you visit your doctor for a complete physical and to
discuss your exercise plans.
Introduction
Thank you for purchasing the GPS Bike computer. This GPS Bike computer is packed with personal Training features like
speed, trip time, laps, etc. Bike computer features include but not limited to the following:
• 12/24H Time format
• Chronograph
• World time
• Dual Time T1 and T2
• 5 daily Alarms
• Bike mode
• Data mode
• Set modes
This Bike Computer can communicate with a PC to store and review your performance.
This Bike computer uses a rechargeable battery that can be charged through USB port of your PC.
Caring for your GPS Bike computer:
Clean your GPS Bike computer with a dampened cloth preferably with mild detergent solution. Wipe dry using a dry cloth. Do
not use chemical cleaners and solvents that may damage plastic components.
Do not store your GPS Bike computer to prolonged exposure to extreme temperatures as this may result to permanent
damage to your unit.
About GPS:
Global Positioning System (GPS) is a satellite- based navigation system made up of a network of 24 or more satellites. GPS
works best in clear weather condition, anywhere in the world, 24 hours a day. Tall buildings may interfere with GPS accuracy.
When 3 satellite signals are received, the Bike computer will have 2D GPS fixed (Latitude and Longitude). When 4 or more
satellite signals are received, the Bike computer will have 3D GPS Fixed.
Getting Started
Step 1) Know your Bike computer:
Push button location:
Step 2) Charging the Battery:
Charge the unit for at least 4 hours before first use. The length of time for a fully charged battery will last depending on the
actual usage. It is recommended to regularly re-charge your battery every 1-2 months even if it is not used to maintain good
battery condition.
2.1) Plug your USB PC link cable to your PC
2.2) Align the charging clip with the contacts on the back of the Bike GPS computer.
2.3) Connect the charging clip securely to the Bike GPS computer.
Note: Please thoroughly dry the charging contacts and surrounding area to ensure proper electrical contact and prevent
corrosion.
When the battery is low, it is time to charge the Bike GPS computer.
Battery low condition:
You cannot turn ON the GPS when the battery is low. The Bike GPS computer will display LOW BATT. You need to recharge
the battery in order to use the GPS again.
When the battery is almost low and you still perform your exercise, your data may not be saved. Please make sure the
battery have enough battery power before doing your exercise in order not to lose your data.
Step 3) Main modes operation
3.1) Press S7 to change modes. The bike computer will show the Mode name for 1.5 seconds before entering the mode itself.
Step 4) Configure your Bike GPS computer:
Before using your Bike GPS computer, please set your Bike computer.
4.1) Go to SET mode and set the following parameters: AUTO LAP, TIME, UNIT, USER, NIGHT, Contrast, CHIME, ALARM,
ODO, and VIEW.
Notes:
• This symbol below means the digits are blinking.
• Press S1/S11 in the succeeding setting screens to change the value of blinking digits
• Press S7 to exi
4.2) AUTO LAP setting:
Notes:
• Auto Lap setting options: (0.5, 1, 2, 3, 4, 5 and OFF). Default is 1 KM.
• ALERT setting option: ON / OFF
4.3) TIME setting: Set Time1 and time 2 separately. You can also set the time through GPS or Manual setting.
Time set through GPS:
Time set manually:
Notes:
• Year range: 2001 to 2099
• Total of 36 City codes for selection
4.4) UNIT setting:
4.5) USER setting:
Note:
Weigh range: 20 to 255 Kg (44 to 561 Lbs) default is 65 Kg (143 lbs)
Height range: 91-241 cm (3’”-7’11” ft’ inch”) default 170 cm
Age Range: 7 to 99. Default is 25
Gender: Male or Female, default is Male
4.6) NIGHT mode setting:
4.7) Contrast setting:
Note: Contrast setting range: 10% to 100%
4.8) CHIME setting:
4.9) ALARM setting:
4.10) ODOMETER setting:
4.11) VIEW setting:
Note:
• You can select the following information to display in Line 2 and Line 3 while it is blinking by pressing S1/S11:
Speed, Calorie, Odometer, Clock, Chrono, and Distance.
4.12) TIME, NIGHT, CONTRAST, & CHIME, can also be set in TIME SET mode.
4.13) AUTO LAP, UNIT, USER, ODO, and VIEW can also be set in BIKE SET mode.
4.14) ALARM can also be set in ALARM SET mode.
Step5) Acquire Satellite signals:
In order to get the correct time of day and begin using your Bike GPS computer, you have to acquire the Satellite signals. It
may take a few minutes to get the signals.
1. Go outside to an open area away from tall buildings and trees. Orient the GPS antenna towards the sky for best
reception. The antenna is located at the 12 o’clock position of the Bike GPS computer.
2. Stand still and do not begin moving while locating the Satellites until the GPS signals are already received.
3. How to Turn ON the GPS: Following are 4 the ways to turn on the GPS.
• Press S1 from any TIME screens to go to BIKE mode
• Press S7 from any TIME screens to go to BIKE mode.
• Press S7 from any BIKE mode screen to enter CHRONO mode.
• Press and hold S7 from any mode for 2 seconds to turn ON the GPS.
4. How to turn OFF the GPS:
• Press and hold S7 from any mode for 2 seconds will turn OFF the GPS.
• When CHRONO is stopped or save, after 10 minutes the Bike computer will auto return to Time view. GPS will be
on standby for 1 hour. GPS ring icon blinks during this time. After 1 hour, the GPS will be turned OFF and the GPS
ring icon is also OFF.
• When you select INDOOR in the GPS/ INDORR selection screen, the GPS will also be OFF.
GPS signals and its meaning:
You will hear a beep sound when the Bike computer has received a GPS signal or when the GPS signal has been lost. LOST
GPS signal will also be displayed in the screen.
Step 6) Go for a Bike:
6.1) Using Bike mode:
6.1.1) Following are the two ways to enter BIKE mode.
Press S1 from any TIME screens:
Press S7 from any TIME screens:
Notes:
• While the computer is searching for the GPS Satellite signal, press S5 to view the remaining BATTERY power
level, remaining DATA TRACK MEMORY and then display the GPS GO screen.
• When you select INDOOR, GPS is OFF.
6.1.2) How to Start, take Lap, Stop and Save.
Notes:
• Bike computer will take auto lap based on auto lap settings.
6.1.3) How to Change views in Line 1:
Notes:
• Line 2 and Line 3 information can be changed in SET mode / VIEW.
• The computer will remember your previous screen view the next time you come back to BIKE mode.
• GPS GO screen will not be shown if the chronograph is already running.
6.1.4) How to view your current data while the chronograph is stopped and before saving.
Notes:
• Before going for a bike exercise, it is highly recommended that you set your user profile first so that the
calories will be calculated properly. Go to SET mode/USER.
• When the Chronograph is stopped and reset in BIKE mode, if no activity for 10 minutes, the GPS will go to
Standby mode and return to TIME mode.
• While in Bike mode, then the GPS signal suddenly becomes weak lost for any reason, the Bike computer
will display LOST GPS signal until it receives GPS signal again.
• Maximum of 15 hours track record / 30 data files/ 100 laps for each data file can be saved in memory.
6.2) Using Chronograph mode:
BIKE & CHRONO modes have the same chronograph counter. When the chronograph is started or stopped in BIKE
mode, the same thing happens in CHRONO mode.
6.2.1) How to enter CHRONO mode.
Notes:If you select INDOOR, the GPS will be OFF and the bike computer will display the INDOOR screen.
6.2.2) How to Start, Stop, take Lap , and Save:
Notes:Bike computer will take auto lap based on auto lap settings.
6.2.3) How to change views in Line 2:
Note:
• GPS GO screen will not be shown if the chronograph is already running.
• The computer will remember your previous screen view the next time you come back to BIKE mode.
6.2.4) How to view your current data while the chronograph is stopped and before saving.
Note:
• When CHRONO is stopped or save, after 10 minutes the Bike computer will auto return to Time view. GPS will
be on standby for 1 hour. GPS ring icon blinks during this time. After 1 hour, the GPS will be turned OFF and
the GPS ring icon is also OFF.
•
Step 7) Download your data to PC:
The Bike Computer comes with PC software to make communication between your Bike Computer and PC easy and
enjoyable. Please install the PC software to your PC using the installer provided. The Bike Computer is using a USB PC link
cable to connect the Bike Computer to PC. Run the GPS PC software on your PC. Plug the USB cable with the Bike
Computer clamped in the other end of the cable. PC software will then prompt you to download the data. Click the download
button to begin downloading. The PC software will prompt to delete the data in the Bike Computer. User has the option to
delete the data in the Bike Computer or not. The PC software installation and instruction guide can be found at the end of this
manual. Please take time to read the guide.
EL backlight:
This Bike Computer has a Night mode function. Following are the options in SET mode and their functions:
10 SECONDS – Press S11 will turn ON the Light for 10 seconds. (Default)
20 SECONDS – Press S11 will turn ON the Light for 20 seconds.
NIGHT ON – Light will continuously ON when CHRONO is running from 5:00 pm to 7:00 am by default. However, Start (ON)
time and END (OFF) Time for the NIGHT function can be changed in Set mode.
TIME mode
• How to change views in TIME mode:
DATA mode
• How to enter the DATA mode:
ALARM mode
• How to go to ALARM mode:
Battery:
The Bike computer is using a rechargeable Lithium Ion battery that will require approximately 4.0 hours charging time using
the USB cable. While battery is charging, the Bike computer cannot be used and all buttons are disabled. User needs to
recharge the battery when the Bike computer indicates a “low battery”. Battery Life (full charge): 8 hrs typical (continuous GPS).
GPS Bike computer troubleshooting guide:
PROBLEM/ QUESTION SOLUTION/ ANSWER
I cannot get a GPS signal
Take your GPS Bike computer outdoors and away from trees and tall buildings.
Remain stationary and try acquiring GPS signal again. Be sure that the antenna is
pointing towards the sky for better signal reception.
Can I reset the unit?
You can reset the Bike computer by pressing S1, S5, S7, and S11 together. The
date and time will be reset to default values. You can set it again manually or
automatically thru GPS.
Will my data and personal settings be lost
after reset?
Your data and personal settings are saved in the flash memory and will not be lost
after Bike computer reset.
The battery indicator does not seem to be
accurate
Allow your GPS Bike computer to fully discharge and then fully charge it without
interruption. It is recommended to regularly re-charge your battery every 1-2 months
even if it is not used to maintain good battery condition.
GPS NE PRO PC SOFTWARE
Your GPS Bike Computer comes with PC software. This software is compatible with the following operating system:
• Windows 7
• Windows XP SP 1, 2, 3
• Windows Vista SP 1, 2
• Windows 2000 SP 4
• Windows 98
You can use the software to view and analyze your data.
Follow this quick start guide to download your data to the PC after your exercises. Use GPS NE Pro PC software that comes
with your GPS Bike Computer.
How to download your data to PC: Follow the easy steps below.
1) Install the GPS NE PRO PC software to your PC. Follow the prompts of the installation wizard and click finish to finish
the installation. You only need to install the PC software once. If the software is already installed on your PC, go directly
to step 2.
2) Double click on the GPS NE PRO icon on your desktop to run the application. A Welcome window will open in your
desktop.
3) Connect the USB charging clip/ Data cable to the GPS Bike Computer. Make sure the four pins in the USB cable is
properly aligned to the four metal contacts at the back of the GPS Bike Computer.
4) Connect the USB charging clip/ Data cable to the PC. The GPS Bike Computer will display CHARGE 90% if there is no
communication yet between the PC and the GPS Bike Computer. The 90% is the charge level of the battery. It will
display PC LINK once the communication has started.
5) Click on the download button in the GPS NE PRO software.
6) The PC software will prompt you to download the data. Click on the Download button.
7) The PC software will prompt you to delete all data from the GPS Bike Computer. Click YES if you want all the data in the
GPS Bike Computer deleted. Click NO if you do not want to delete all data (Recommended).
8) You click enter to view the downloaded data.
9) The HOME page of the PC software will open displaying various information, Data file, and settings. Click on any of
these icons to go directly to the desired data, information or settings.
10) The PC software will then display the data that you have selected. Various tabs will also be displayed at the top of the
screen. You can click on any of these tabs to enter the selected function.
11) Press the HOME button to go back to the home page or just exit the PC software after you are done.
How to SET your GPS Bike Computer:
There are two possible ways to SET your GPS Bike Computer.
1) Setting the GPS Bike Computer manually in SET mode
• Press S7 from ALARM mode to enter SET mode.
• Press S1/S11 to select which parameter to set
• Press S5 to enter the selected parameter
• Press S1/S11 to change or SET the value.
• Press S7 to exit.
• Refer to the Instruction manual for the detailed setting procedure.
2) Setting the GPS Bike Computer using the GPS NE PRO PC software:
• The GPS NE PRO PC software can be used to SET the parameters of the GPS Bike Computer. This can be
done by synchronizing the settings in the PC software to the GPS Bike Computer. It can also be used to get
the Setting of the GPS Bike Computer and copy to the PC software.
2.1) Synchronizing PC software setting to set the GPS Bike Computer:
• Connect the GPS Bike Computer to the PC using the USB Charging clip/ Data cable.
• Click the USER setting in the HOME page of the PC software.
• The PC software will display the various parameters to be set. Fill in all the required information.
• After filling in all the required information, click the Synchronize with your computer button at the bottom
right of the screen.
• The PC software will prompt you will successful synchronization. Or Try again message if it fails. It will
also display errors if there are invalid inputs on required fields. Correct the invalid inputs and try again.
2.2) Getting the GPS Bike Computer setting and copy it to GPS NE PRO PC software:
• Connect the GPS Bike Computer to the PC using the USB Charging clip/ Data cable.
• Click the USER setting in the HOME page of the PC software.
• The PC software will display the various parameters to be set.
• Click the GET SETTING button at the bottom center of the screen.
All the GPS Bike Computer settings are now copied to the PC software.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Outbound GR-C100 User manual
- Category
- Bicycle accessories
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Timex W260 User manual
-
-
-
-
-
Epson E11E209023 User manual
-
Globalsat GH-505 User manual
-
Epson Runsense SF-310G Fitness Band User manual
-
-
Suunto Ambit Black (HR) User guide