U-Line UCBR632-SS01A User Guide & Service Manual

USER GUIDE & SERVICE MANUAL

Model: UCBR632-SS01A

USER GUIDE & SERVICE MANUAL

Table of Contents

Click on any section below to jump directly there

Intro

Safety

Safety and Warning

Disposal And Recycling

Installation

Environmental Requirements

Electrical

Cutout & Product Dimensions

General Installation

Grille Installation

Door Swing

Door Adjust

Interior Adjustments

Maintenance

Cleaning

Cleaning Condenser

Extended Non-Use

Operating Instructions

First Use

Control Operation

Airflow and Product Loading

Service

Troubleshooting

Wire Diagram

Product Liability

Warranty Claims

Ordering Replacement Parts

R600a Specifications

System Diagnosis Guide

Compressor Specifications

Troubleshooting Extended

Control Operation - Service

Thermistor

Defrost

Remove Fan and Cover

Warranty

USER GUIDE

Introduction

WELCOME TO U-LINE

Congratulations on your U-Line purchase! Your product comes from a company with decades of premium modular ice

making, refrigeration, and wine preservation experience. U-Line creates products focused on functionality, style, and

inspired innovations — paying close attention to even the smallest details. Applications include residential, outdoor, ADA

height compliant, marine, and commercial. Product categories include Beverage Centers, Wine Refrigerators, Ice Machines,

Refrigerators, Freezers, and Dispensers. Our advanced refrigeration systems, large and exible capacities, and clean

integrated look are what makes our products Built-In to Stand Out®. Since 2014, U-Line has been part of the Middleby family

of brands. Products are designed, engineered, and assembled in Milwaukee, Wisconsin, USA, and select products are available

worldwide.

U-Line — RIGHT PRODUCT. RIGHT PLACE. RIGHT TEMPERATURE.®

PRODUCT INFORMATION

Looking for additional information on your product? User Guides, Spec Sheets, CAD Drawings, and Product Warranty

information are available digitally on u-line.com.

PROPERTY DAMAGE / INJURY CONCERNS

In the unlikely event property damage or personal injury is suspected related to a U-Line product, please take the following

steps:

1. U-Line Customer Care must be contacted immediately at +1.414.354.0300.

2. Service or repairs performed on the unit without prior written approval from U-Line is not permitted. If the unit has been

altered or repaired in the eld without prior written approval from U-Line, claims will not be eligible.

GENERAL INQUIRIES

U-Line Corporation

8900 N. 55th Street

Milwaukee, Wisconsin 53223 USA

Monday - Friday 8:00 am to 4:30 pm CST

T: +1.414.354.0300

Email: sales@u-line.com

u-line.com

CONNECT WITH US

SERVICE & PARTS ASSISTANCE

Monday - Friday 8:00 am to 4:30 pm CST

T: +1.414.354.0300

Service Email: onlineservice@u-line.com

Parts Email: onlineparts@u-line.com

Designed, engineered and assembled in WI, USA

3

USER GUIDE

Safety and Warning

NOTICE

Please read all instructions before installing,

operating, or servicing the appliance.

Use this appliance for its intended purpose only and follow

these general precautions with those listed throughout this

guide:

SAFETY ALERT DEFINITIONS

Throughout this guide are safety items labeled with a

Danger, Warning, or Caution based on the risk type:

Danger means that failure to follow this safety

statement will result in severe personal injury or

death.

Warning means that failure to follow this safety

statement could result in serious personal injury

or death.

Caution means that failure to follow this safety

statement may result in minor or moderate

personal injury, property, or equipment damage.

Caution: risk of re, ammable refrigerant and

blowing gas used.

GENERAL PRECAUTIONS

Use this appliance for its intended purpose only and follow

these general precautions with those listed throughout this

guide.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience or knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not

play with this appliance.

Keep clear of obstruction all ventilation openings

in the appliance enclosure or in the structure for

building-in.

Please accord to local regulations regarding

disposal of the appliance for its ammable

refrigerant and blowing gas. Before you scrap the

appliance, please remove the doors to prevent

child entrapment.

Do not store explosive substances such as

aerosol cans with a ammable propellant in this

appliance.

Do not use mechanical devices or other means

to accelerate the defrosting process, other than

those recommended by the manufacturer.

Do not damage the refrigerating circuit.

Do not use electrical appliances inside the food/

ice storage compartments unless they are of the

type recommended by the manufacturer.

DANGER

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

CAUTION

!

4

USER GUIDE

Safety and Warning

DO NOT use medical devices or other means to

accelerate the defrosting process other than

those recommended by the manufacturer. DO

NOT use an ice pick or other sharp instrument to

help speed up defrosting. These instruments can

puncture the inner lining or damage the cooling

unit. DO NOT use any type of heater to defrost.

Using a heater to speed up defrosting can cause

personal injury and damage to the inner lining.

NOTICE

Do not lift unit by door handle.

Never install or operate the unit behind closed

doors. Be sure front grille is free of obstruction.

Obstructing free airow can cause the unit to

malfunction and will void the warranty.

Failure to clean the condenser every six months

can cause the unit to malfunction. This could void

the warranty.

Allow unit temperature to stabilize for 24 hours

before use.

Do not block any internal fans.

Use only genuine U-Line replacement parts.

Imitation parts can damage the unit, aect its

operation or performance and may void the

warranty.

This appliance is intended to be used in household and

similar applications such as:

• Sta kitchen areas in shops, oces and other working

environments.

• Farm houses and by clients in hotels, motels and other

residential type environments.

• Bed and breakfast type environments.

• Catering and similar non-retail applications.

5

USER GUIDE

Disposal and Recycling

RISK OF CHILD ENTRAPMENT. Before you throw

away your old refrigerator or freezer, take o

the doors and leave shelves in place so children

may not easily climb inside.

If the unit is being removed from service for disposal,

check and obey all federal, state, and local regulations

regarding the disposal and recycling of refrigeration

appliances, and follow these steps completely:

1. Remove all consumable contents from the unit.

2. Unplug the electrical cord from its socket.

3. Remove the door(s)/drawer(s).

DANGER

!

6

USER GUIDE

Environmental Requirements

This unit is designed to operate between 50°F (10°C) and

100°F (38°C). Higher ambient temperatures may reduce

the unit’s ability to reach low temperatures and/or reduce

ice production on applicable models.

For best performance, keep the unit out of direct sunlight

and away from heat generating equipment.

In climates where high humidity and dew points are

present, condensation may appear on outside surfaces.

This is considered normal. The condensation will

evaporate when the humidity drops.

CAUTION

!

Damages caused by ambient temperatures of

40°F (4°C) or below are not covered by the

warranty.

7

USER GUIDE

Electrical

WARNING

!

SHOCK HAZARD — Electrical Grounding

Required. Never attempt to repair or perform

maintenance on the unit until the electricity has

been disconnected.

Never remove the round grounding prong from

the plug and never use a two-prong grounding

adapter.

Altering, cutting or removing power cord,

removing power plug, or direct wiring can cause

serious injury, fire, loss of property and/or life,

and will void the warranty.

Never use an extension cord to connect power to

the unit.

Always keep your working area dry.

NOTICE

Electrical installation must observe all state and

local codes. This unit requires connection to a

grounded (three-prong), polarized receptacle

that has been placed by a qualified electrician.

The unit requires a grounded and polarized 115 VAC,

60 Hz, 15A power supply (normal household current). An

individual, properly grounded branch circuit or circuit

breaker is recommended. A GFCI (ground fault circuit

interrupter) is usually not required for fixed location

appliances and is not recommended for your unit because

it could be prone to nuisance tripping. However, be sure

to consult your local codes.

See CUTOUT & PRODUCT DIMENSIONS for recommended

receptacle location.

8

USER GUIDE

Cutout & Product Dimensions

PREPARE SITE

Your U-Line product has been designed for either

freestanding or built-in installation. When built-in, your

unit does not require additional air space for top or rear.

However, the front grille must NOT be obstructed, and

1-inch clearance is required for proper air ow on the

mechanical side of the unit.

CAUTION

!

Unit can NOT be installed behind a closed cabinet

door.

CUTOUT & PRODUCT DIMENSIONS -

UCBR532/UCBR632

NOTE:

THE HOLE CUTOUTS ON TOP SURFACE APPLY TO

THE UCBR632 ONLY AND ARE CUTOUT AT THE

FACTORY.

FRONT

TOP

SIDE

34 1/2"

(878mm)

30 15/32"

(773mm)

32"

(813mm)

19 1/4"

(489mm)

28"

(711mm)

43 1/4"

(1099mm)

24 3/4"

(630mm)

18 1/2"

(468mm)

24 3/4"

(630mm)

26 19/32"

(676mm)

33"

(838 mm)**

Preferred location for electrical

outlet is in an adjacent cabinet

on the mechanical side of the unit.

34 7⁄8”

(886 mm)*

25"

(635 mm)

Power cord length is

approx. 71⁄2 feet (2289 mm)

* If Unit has Legs, Add 6” - 6 3⁄4”, if Casters Add 5”

** For Proper Airow, 1” Clearance Required on Mechanical Side

9 31/32"

(253mm)

12 31/32"

(329mm)

7"

(178mm)

32"

(813mm)

24 3/4"

(629mm)

2 3/4"

(70mm)

1"

(25mm)

9

USER GUIDE

Cutout & Product Dimensions

TAP TOWER KITS

This template is to be used as reference if you want to add

your own tap tower kit.

NOTES

• Dotted box shows safe drill area.

• Dotted holes show reference tap holes in air duct

below lid.

• It is recommended to insulate any tubing inside of

the air duct to avoid freezing.

• Left-hand units are dimensionally opposite left-to-

right.

DRILL AREA

4”

(102mm)

15 3⁄4”

8 5⁄8”

(400mm)

13 5⁄8”

(346mm)

(219mm)

52”

DRILL AREA

4”

(102mm)

15 3⁄4”

8 5⁄8”

(400mm)

13 5⁄8”

(346mm)

(219mm)

72”

DRILL AREA

4”

(102mm)

15 3⁄4”

8 5⁄8”

(400mm)

13 5⁄8”

(346mm)

(219mm)

92”

DRILL AREA

4 1⁄4”

4”

(108mm)

(102mm)

8 5⁄8”

(219mm)

32”

15 3⁄4”

(400mm)

10

USER GUIDE

General Installation

WARNING

!

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, injury, or death.

WARNING

!

Incorrect installation or any modications made

to the appliance may damage property or result

in injury or death.

WARNING

!

Appliance maintenance must be carried out by

only by suitably trained personnel.

WARNING

!

All replacement parts that are not supplied by

U‑Line must be preapproved before installation.

WARNING

!

Before any maintenance work is performed,

the appliance must be disconnected from the

electrical supply. Apply a lockout tag to the

electrical supply connection.

PERSONNEL

Sta who use and install the appliance must possess (or

acquire through adequate training) the following skills and

must understand the Manual instructions and all relevant

Safety information:

• General technical knowledge to understand the

Manual’s instructions

• Awareness of the main hygiene, accident prevention,

and technological regulations

PUTTING INTO OPERATION

If the equipment has been placed in a horizontal position

during transport, it cannot be put in operation immediately.

Put the unit in a vertical position, then wait about

two (2) hours to operate it.

SET UP

Initial startup requires no adjustments. If the unit was

turned o, press to turn unit on. See “Control

Operation” section for more details.

NOTICE

Temperature displayed reects actual

temperature inside unit.

If the temperature displayed is dierent than

selected, the unit is progressing towards the

selected temperature. Time to reach set point

varies based upon ambient temperature,

temperature of product loaded, door openings,

etc. U‑Line recommends allowing the unit to

reach set points before loading.

To continue to set up the unit, perform the following steps:

1. Remove the packaging from the refrigerator. Assess

the area:

◦ if the vertical space is high enough, lift the box up

◦ if the vertical space is not high enough, cut away

the cardboard in sections and pull them away

NOTE: Make sure the unit stays vertical.

2. Remove the white PVC protection lm from the

stainless steel and all other protection used by the

company to reduce the risk of damage during transport

3. Place the refrigerator on a at level surface.

4. Before use, clean the refrigerator with a clean, soft

cloth and appropriate spray product.

NOTE: Use minimal water because it contains

minerals that leave traces of dirt, which

are dicult to remove.

5. Wash the tray and all internal parts, using commercial

anti‑bacterial detergents.

6. Remove the detergent with a soft sponge soaked in

water and dry with a clean, soft cloth.

NOTE: Do not use abrasive detergents or

powders, which could cover the nish with

a lm.

11

USER GUIDE

General Installation

NOTE: Use minimal water for cleaning. Too much

water can damage electric parts; a damp

sponge is sucient.

7. Install the shelf supports where needed.

8. Insert each support into the holes at the base of the

refrigerator.

9. Insert the side tab in the appropriate place on the

sides or on the table supports.

10. Slide the shelf into the supports.

Figure 1: Shelf Sliding into Supports

11. On the lower part of the refrigerator, slide the

condensation waste tray into the appropriate runner.

Evaporation

condensing

water tray

Guide

Figure 2: Tray Guides

12. For appliances that have automatic trays, connect the

connector.

See the “Cutout and Product Dimensions” and “Control

Operation” sections for more details.

12

USER GUIDE

Grille Installation

REMOVING AND INSTALLING GRILLE

Disconnect electric power to the unit before

removing the grille.

When using the unit, the grille must be installed.

Removing the grille

1. Disconnect power to the unit.

2. Remove two top screws and two bottom screws.

3. Remove grille and set aside

Installing the grille

1. Align cabinet and grille holes and secure top and

bottom. Do not over tighten grille screws.

2. Connect power to the unit.

WARNING

!

Remove

Top Screws

Remove

Bottom Screws

13

USER GUIDE

Door Swing

Units have a zero clearance for the door to open 90°,

when installed adjacent to cabinets.

Stainless Steel models require 2-1/8" (54 mm) door

clearance to accommodate the handle if installed next to a

wall.

Wall

90°

Door Swing

2-1/8" Min.

(54 mm)

14

USER GUIDE

Door Adjustments

3. Remove hinge pin from top hinge using a 1/8” hex key

tool. Rotate hinge pin clockwise to remove. Set aside.

4. On the bottom hinge use a Philips screwdriver to

remove screw holding the plastic door closer.

5. Reinstall plastic door closer on the other hinge

(formerly the top hinge).

6. With 1/8” hex key install hinge pin onto top hinge

(formerly the

bottom hinge) until

even with surface

of hinge.

7. Install top and

bottom hinges on opposite side of cabinet. Install 3

leftover screws into the open holes.

8. Install top and bottom lock brackets.

Door Adjustments

REVERSING THE DOOR

Location of the unit may make it desirable to mount the

door on the opposite side of the cabinet.

The hinge hardware will be removed and reinstalled on the

opposite side of the cabinet.

TO REVERSE THE DOOR

Note: When reversing the door, the top hinge

becomes the bottom hinge on the opposite side

of the unit - likewise, the bottom hinge becomes

the top on the other side.

REMOVE DOOR

1. With door closed, remove hinge pin from bottom hinge

using a Philips screwdriver.

2. Remove the door by lifting it slightly and pulling

bottom of door toward you until clear of the bottom

hinge.

MOVE HINGES TO OPPOSITE SIDES

Note: When removing hardware from the unit,

keep all screws and parts handy, they will all be

needed.

1. Using a Phillips

screwdriver, remove

both hinges by taking

out 6 screws. Also

remove 6 screws from

the other side.

2. With the same Philips

screwdriver, remove

4 screws holding the

lock brackets. The

lock brackets will

be installed on the

opposite side.

Remove Hinge Pin

with Philips Screwdriver

Plastic

Door Closer

Screw

Door Closer

Screw

LOCK

BRACKET

REMOVE

HINGE SCREWS

REMOVE

HINGE SCREWS

LOCK

BRACKET

15

USER GUIDE

Door Adjustments

PREPARE DOOR FOR INSTALLATION

1. Stand door up on bottom edge, handle side facing

you.

2. Remove top hinge plate by using a 5/32” hex tool to

take out two screws. Hinge plate, two hex screws,

and bushing will be used on opposite surface.

3. Pry out hinge pin busing.

4. Flip door over so gasket side is facing you.

5. Take out two 5/32” screws to remove bottom hinge

plate. Set aside.

6. Install hinge pin bushing into door.

7. Install the top hinge plate (the one just removed from

the opposite surface) over installed hinge pin bushing.

8. Take bottom hinge plate and remove closer cam with

a Philips screwdriver, and reinstall closer cam on

opposite surface of bottom hinge plate.

9. Flip door over and install bottom bottom hinge plate.

INSTALL DOOR ONTO UNIT

Note: To prevent damage and to have two hands

free, it may be benecial to have someone hold

the door during the installation.

1. Lift door at a slight angle upward to allow the hinge

pin to slide into the hinge hole on the door.

2. Position bottom of door to line up the door closer with

the door closer cam.

3. Insert lower hinge pin through hinge. Use a Philips

screwdriver to tighten.

4. Test door to make sure it opens and closes correctly.

5. Test lock.

Left-Hand

Hinged Door

Right-Hand

Hinged Door

BOTTOM SURFACE OF DOOR

Closer Cam

Hinge Plate Hinge Plate

Left-Hand

Hinged Door

Hinge Pin

Bushing

Hinge Plate Hinge Plate

Right-Hand

Hinged Door

TOP SURFACE OF DOOR

Line up

Closer Cam

with Closer

Hinge Pin

BOTTOM SURFACE OF DOOR

Hinge Pin

Bushing

Left-Hand

Hinged Door

Right-Hand

Hinged Door

Hinge Plate Hinge Plate

A. Remove Closer Cam

& Flip Hinge Plate over

B. Install Hinge Plate

AB

Left-Hand

Hinged Door

Right-Hand

Hinged Door

16

USER GUIDE

First Use

NOTICE

Temperature displayed reects actual

temperature inside unit.

If the temperature displayed is dierent than selected, the

unit is progressing towards the selected temperature. Time

to reach set point varies based upon ambient temperature,

temperature of product loaded, door openings, etc. U-Line

recommends allowing the unit to reach set points before

loading.

First Use

Initial startup requires no adjustments. If the unit was

turned o, press to turn unit on. See “Control

Operation” section for more details.

17

USER GUIDE

Control Operation

CONTROL FUNCTION GUIDE

DOOR ALERT NOTIFICATION

When the door is left open for more than 30 minutes:

• A tone will sound for several seconds every minute

• will appear in display

• Close door to silence alert and reset

FUNCTION COMMAND NOTES

ON/OFF Press and release Unit will immediately turn ON or OFF

Adjust Temperature Press or and release

When the display is ashing, press or to

adjust the set point temperature. Note: temperature

displayed is the actual temperature inside unit

Toggle between oF / oC Hold and for 5 seconds. The display will change units

Leave interior light on

Press and release to leave interior

light on for 12 hours; press again to

deactivate

After 12 hours, factory default is restored; light will

turn on when door is open

Hide Display Hold and press

Display will turn o when door is closed. Unit will

continue to operate. Repeat command to turn on

display

Adjust Light Color While holding press and release

to scroll through lighting options

Option Open Door Closed Door

White White

Blue Blue

White Blue

Light will be set at full intensity when door is open,

and 50% intensity when door is closed.

Showroom Mode Hold and for 5 seconds

The ºF / ºC symbol will ash. Display will be lit and

interior light will function. Unit will not cool. Repeat

command to return to normal operation

18

USER GUIDE

Airow & Product Loading

Airow and Product Loading

AIRFLOW

External

• Do not block the front grille

• A minimum of 1” clearance is required on the grille-

side of the unit.

• Do not install behind a closed door

Internal

• When loading, leave space between internal fans,

vents, and side walls to allow air to circulate freely

NOTICE

Restricting airow may result in poor product

performance, product failure, and uneven internal

temperatures and may freeze contents.

A Minimum

clearance

of 1” is required

for proper airow.

Grille

19

USER GUIDE

Interior Adjustments

REMOVING AND INSTALLING SHELVES

Adjusting Interior Shelves

Models equipped with wire rack or glass cantilever shelves

have an adjustable mounting system. To adjust or simply

remove shelves for cleaning, follow the instructions below.

1. Remove all product from shelf.

2. Coming from underneath the shelf, lift both the front

and rear of the shelf.

3. Carefully slide shelf out of unit being careful not to

scratch the interior liner.

4. Installation is the reverse of removal.Adjusting

Shelf Height

Shelf height may be adjusted to accommodate a broad

range of product. To alter your shelf spacing follow the

instructions below.

1. Remove the 4 Shelf clips from the shelf clip holes.

2. Move shelf clips as a group to the desired shelf height.

3. Insert shelf clips into the holes of the desired shelf

height. Be certain shelf clip is fully seated into shelf

clip hole.

Clips MUST be installed with the ribbed side

down. Failure to do so may result in shelf or unit

damage.

NOTICE

All 4 shelf clips for each shelf must be installed at

the same height for shelf stability.

4. Reinstall shelf.

Cleaning Shelves

Shelves may be cleaned in a soapy warm water solution. A

general household disinfectant may be used if necessary.

Be sure to completely dry your shelf before reinstalling.

Door Locking/Unlocking

Models equipped with locking doors can be set to the lock

position by inserting the included keys into the lock plugs

and rotating clockwise. To unlock, use the key to turn the

lock plug counter-clockwise.

Clip Holes

20

Page is loading ...

U-Line UCBR632-SS01A User Guide & Service Manual

U-Line UCBR632-SS01A User Guide & Service Manual

Related papers

Other documents