ML Accessories IPREMOTE User manual

Brand: ML Accessories

Model: IPREMOTE

Type: User manual

ML Accessories Limited

LU5 5TA

www.mlaccessories.co.uk SBJUN15_V1 89

INSTALLATION & MAINTENANCE MANUAL

IP663G and IP665G

230V

50Hz

Power led

Load compression glands

Remote control

IP665G - 5 Channel control

Indicator LED

Fig 4

Fig 3

Supply compression gland

Cable clamps

Fig 2

I II III IV V

Match

switch

1 2 3

These instructions should be read carefully and retained after installation by the end user for future

reference and maintenance.

These instructions should be used to aid installation of the following products:

IP663G & IP665G

GENERAL INSTRUCTIONS:

SAFETY:

INSTALLATION:

• Installation of this product should only be carried out by a qualiﬁed electrician or competent person

to the current IEE Wiring Regulations (BS7671)

• Before installation/maintenance, ensure that all mains supply is isolated

• Check the total load on the circuit, including when this product is ﬁtted, does not exceed the rating

of the circuit cable, fuse or circuit breaker

•

Please note the IP (Ingress of Protection) rating of this product when deciding the location for

installation

• This product is Class I and requires an Earth

• The IP rating of this product will be compromised if the drain hole is opened

• Ensure the maximum load is not exceeded when installing

• Please recycle this unit

GENERAL:

SETTING UP THE REMOTE CONTROL:

WARRANTY:

• The unit should be recycled in the correct manner when it reaches the end of its life. Check local

authorities for where facilities exist

• Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may

damage the product

• Provide power to the required point of installation, suitable IP rated junction boxes should be used

where required

• If installing outdoors, ensure the power source is via a suitable IP rated enclosure

• The power source connections should be local and accessible

• Remove 4 ﬁxing screws around the top cover

• Using the back box as a template, mark the location of the ﬁxing holes

•

When drilling the holes, ensure they do not infringe with electrical cables, water or gas pipes or

ceiling joists

• Ensure suitable wall ﬁxings are used

• Reﬁt the screw mounting hole caps (failure to ﬁt these caps will compromise the IP rating)

• Note the load compression glands should be facing downwards

• Remove items 1, 2 and 3 from the supply compression gland (see Fig 2), items 1 & 3 slip over the

incoming cable

• Connect the incoming power ACL – LIVE (BROWN), ACN – NEUTRAL (BLUE) and FGND - EARTH

(GREEN/YELLOW)

• Secure the cable in place via the cable clamp (see Fig 2), then connect the compression gland

ensuring a good ﬁt around the cable

• Ensure the gasket is ﬁtted to the inside of the lid and ﬁx the lid to the back box using the screws

provided

• Various loads may be controlled please see ﬁg 1 below. Connections are FGND – EARTH (GREEN/

This product has a warranty of 1 year from date of purchase. Failure to install this product in

accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of

the batch codes will invalidate the warranty. If this product should fail within its warranty period it

should be returned to the place of purchase for a free of charge replacement. ML Accessories does

not accept responsibility for any installation costs associated with the replacement product. Your

statutory rights are not affected. ML Accessories reserve the right to alter product speciﬁcation

without prior notice

Important Warning:

Each switch is individually fused and the rating of the fuse is marked on the terminal connector

in front of fuse. Do not exceed the maximum load shown below via each of the compression

glands (Fig 1).

Load Compression

Part code Gland I Gland II Gland III Gland IV Gland V

IP663G 8A 2.5A 2.5A n/a n/a

IP665G 5A 2.5A 2.5A 2A 1A

(Fig 1)

• Remove battery cover from remote control

• Insert an AAA 1.5V battery to the remote control (not supplied) and replace cover

• Press the “MATCH” switch on the circuit board (see Fig 2) once, the “GREEN” power LED will start

blinking

• Press any button on the remote control handset and hold it until the “GREEN” power LED is stable

and not blinking

• Press the “ON” button on channel 1 of the remote control; the Channel 1 indicator LED will illuminate

RED (see Fig 3)

• Once Channel 1 is programmed the other channels will be set up automatically

• The remote control is now ready for use

• Switch on and check for correct operation

Note: The remote control must be set up before the load is installed.

ML Accessories IPREMOTE User manual

ML Accessories IPREMOTE User manual

ML Accessories IPREMOTE User manual

Related papers

Other documents