Sharper Image Dual Jet Spa User manual

Brand: Sharper Image

Model: Dual Jet Spa

Type: User manual

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be taken, including

the following. Read all instructions before using this appliance.

DANGER – To reduce the risk of electric shock:

1) Always unplug this appliance from the electrical outlet immediately after using or before

cleaning.

2) Do not place or store power pack where it can fall or be pulled into a tub or sink. Do not fully

immerse in or drop into water or other liquids. Store in a dry place, out of reach of children.

3) Do not reach for an appliance that has fallen into water. Unplug immediately.

WARNING – To reduce the risk of burns, fire, electric shock, or injury

to persons:

1) An appliance should never be left unattended when plugged in. Unplug from outlet

when not in use and before putting on or taking off parts.

2) This appliance is not a toy!

3) Consult your doctor before using in case of pregnancy, illness, medical condition, or

persistent pain.

4) Do not use on any unexplained pain or swollen muscles, or following a serious injury,

before consulting your physician.

5) Do not use appliance in close proximity to loose clothing or jewelry.

6) Keep long hair away from appliance while in use.

7) This appliance should not be used by, on, or near children or individuals with certain

disabilities.

8) Use this appliance only for its intended use as described in this manual. Do not use

attachments not recommended by Conair.

9) Never operate this appliance if it has a damaged cord or plug, if it is not working

properly, or if the power pack has been dropped or submersed in water. Return the

appliance to a service center for examination and repair.

10) Do not carry this appliance by the power-supply cord or use the cord as a handle.

11) Keep the cord away from heated surfaces.

12) Never drop or insert any object into the product.

13) Do not use outdoors.

14) Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

15) For use with the Conair-supplied adapter CA79 only.

16) Use the class 2 power supply in a dry location only.

17) This power unit is intended to be correctly oriented in a vertical or floor-mounted position.

18) Do not handle plug with wet hands. Ensure that your hands are dry when operating the

controls or removing the plug.

19) To disconnect, turn to the OFF position, then remove plug from outlet.

20) This appliance is for household use only.

21) Never use while sleeping or drowsy.

22) Keep out of the reach of children.

IMPORTANT

Keep hair, fingers, skin, and loose clothing or articles away from suction openings located on

sides of unit while Hydro Spa is in operation. Otherwise, personal injury may result. Use of a

shower cap is recommended for persons with long hair. Do not use the Hydro Spa with bath

oil in the tub water, as this may affect performance of unit.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

CAUTION

• This unit should not be used in the following cases unless directed by physician:

tuberculosis, benign and malignant tumors, hemorrhages, inflammations of the skin,

phlebitis and thrombosis, open and fresh wounds, bruises, broken skin or varicose veins,

or undetermined calf pain.

• Consult your physician if you have any questions regarding therapeutic use of this Hydro

Spa.

• Do not use if you have any unexplained pain before consulting your physician.

• Discontinue use of unit if pain is present or increases or if swelling occurs after use.

• Do not use on any part of the body that is anesthetized.

• Do not use if you’ve had recent surgery.

• Never use without removable filters.

• If you are pregnant, consult your physician before use.

• Never run your Hydro Spa without water.

• Read safety and operating instructions carefully. This product is intended for indoor use on

permanent right-wall tubs. Do not use outdoors or on the walls of inflatable tubs or pools.

HOW TO USE

1) With unit securely placed on tub (see “How to Attach Your Hydro Spa to Your Tub”), place

the power pack as far away from tub as possible so that it cannot easily be pulled into tub.

2) Hydro Spa is connected to the power pack by a 15 ft. line cord. Insert plug into power

pack with indexing tab facing down.

3) Plug power pack into 120V wall outlet. Make sure power pack is not on the floor of the

bathroom to minimize water exposure to the power pack.

4) Fill bathtub with warm water. Ensure water temperature is comfortable to avoid burns. Never

use boiling water with your Hydro Spa.

5) Adjust height of motor assembly so that water jets are beneath water. This can be done

by moving the motor assembly up and down vertically; the housing employs detents that

hold the motor assembly at the desired height. KEEP THE WATER LEVEL IN THE TUB

ABOVE THE FILL LINE ON BODY OF DEVICE.

6) Point the water jets downward.

7) Adjust the control switch on the side of the unit to either “Jet Stream” or “Bubbles”

(see Fig. 1).

8) Turn the knob on the top of the Hydro Spa to ON (see Fig. 2).

9) Adjust the water jets to create customized water flow in your bathtub.

10) After use, turn the knob to the OFF position (see Fig. 2), drain water from tub, then

remove Hydro Spa.

11) Tilt your Hydro Spa gently over the bathtub to remove excess water, and dry with a soft

cloth before storage.

CAUTION: IF Hydro Spa FALLS AND BECOMES

COMPLETELY IMMERSED IN WATER IN TUB, DO NOT

PANIC. UNPLUG FROM WALL OUTLET FIRST. THE Hydro

Spa HAS BEEN DESIGNED TO WITHSTAND SUBMERSION.

UNPLUG FROM WALL OUTLET FIRST, THEN REMOVE UNIT

FROM BATHTUB. TURN UNIT OFF, DRAIN WATER FROM

TUB, AND STORE UNIT IN A DRY PLACE.

NOTE

You may experience some water spray if the unit shifts during operation. Do not overfill your

tub. For best results, get into your tub before filling.

(Note: Too much water can cause overflow.)

The Conair® Jet Hydro Spa can help you relax, relieve tension, and soothe sore muscles.

Consult your physician or physical therapist for recommendations regarding Hydro Spa use,

including water temperature, duration, and frequency.

CARE AND MAINTENANCE

1) Keep your unit clean and clear of obstruction. Check the water jets

and inlet filters periodically to make sure they are free of obstruction,

hair, lint, and other particles that could block air or water flow. Clean

inlet filters by removing filter caps and rinsing cap under running

water. Reinsert on Hydro Spa by using the provided alignment

marks. See “Fitting and Removing Filter Caps.”

2) Store your Hydro Spa in a cool, dry place. Loosely coil the power

cord and lay flat to store. Do not wrap cord around Hydro Spa or

power pack.

FEATURES

1) Dual multidirectional water jets

2) Telescopic housing

3) Jet stream or bubbles switch

4) Removable filters

5) Compact convenience

Foldable arm

for easy storage OFF/ON

Adjustable

suction cup

for edge of tub

3) Bubbles/Jet Stream

control switch on side

2) Adjustable

motor height

Suction cups

for bathtub wall

Filter

alignment tabs

4) Removable

filter on each side

1) Dual

multidirectional

water jets

Jet Stream Bubbles

Fig. 1

Fig. 2

For your safety and continued enjoyment of this product,

always read the instruction book carefully before using.

All HYD100 Models

™

Fig. 3 Fig. 5

CLEANING YOUR Hydro Spa

1) Clean your Hydro Spa after each use by wiping with a clean cotton cloth. Do not immerse

the entire unit in water.

2) Clean your unit periodically by wiping it with a damp cotton cloth.

RECOMMENDED USE TIME

We recommend using the Jet Hydro Spa for 15-20 minutes at a time.

HOW TO ATTACH YOUR Hydro Spa TO YOUR TUB

1) Make sure the power knob is in the OFF position. The tub should be clean and empty of

water.

2) Extend the folding arm and position unit along edge of tub so the unit is inside the tub and

the arm is resting on edge (Fig. 3).

3) Moisten suction cups on motor housing of Hydro Spa to increase grip.

4) Secure suction cups by gently applying even pressure on Hydro Spa against tub wall

(Fig. 3).

5) Adjust suction cup on arm so that it adheres directly onto bathtub edge. See Fig. 4 and

following “Suction Cup Position Adjustment” section (Fig. 6).

6) Adjust height of motor assembly to desired depth by moving motor housing up or down

by hand. Built-in detents will hold the position you desire (Fig. 5).

7) Water may spray if unit is not level when turned on.

Fig. 4

Please register this product at register.conair.com

SERVICE CENTER

Conair LLC

Service Department

7475 N. Glen Harbor Blvd.

Glendale, AZ 85307

Visit us on the web at: www.conair.com

stock.image

HYD100

22PS084456 IB-17743

SUCTION CUP POSITION ADJUSTMENT

Suction cup underneath the handle can be in one of two positions to suit different bathtubs

(see Fig. 6).

Push and slide the suction cup to the desired position.

Position A: The outermost position for thick-sided tubs.

Position B: The innermost position for thin-sided tubs.

FITTING AND REMOVING FILTER CAPS

TO REMOVE CAPS

1) Filter caps are located on either side of the motor assembly.

2) Turn cap about 20° counterclockwise (Fig. 7).

3) Line up single hash mark on cap with the center

seam on the back body of the unit.

4) Pull cap away from unit.

5) Rinse cap under water to remove hair, lint, etc.

TO REPLACE CAPS

1) Push cap into body so that single hash mark on cap lines up with the center seam on the

back body of the unit.

2) Turn cap clockwise about 20° until the double hash marks on the cap line up with the

center seam on the back body of the unit.

WARNING: To help prevent excess lint, hair, etc., from getting caught in motor, unit

should never be used with the filter cap removed. Injury or damage to unit could result.

LIMITED ONE-YEAR WARRANTY

(U.S. and Canada Only)

Conair will repair or replace (at our option) your appliance free of charge for 12 months from

the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed,

together with your sales receipt. California residents need only provide proof of purchase

and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase

receipt, the warranty period will be 12 months from the date of manufacture. ANY IMPLIED

WARRANTIES, OBLIGATIONS OR LIABILITIES, INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, SHALL BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS

WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY,

EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation

of special, incidental or consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary

from state to state.

Position B

Fig. 6

Position A

Fig. 7

FEDERAL COMMUNICATIONS COMMISSION NOTICE

WARNING: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

SUPPLIER’S DECLARATION OF CONFORMITY

Brand: CONAIR

Model No.: HYD100

Description: JET HYDRO SPA

Responsible Party: Conair LLC, 1 Cummings Point Road, Stamford, CT 06902

1-800-334-4031

Standards: FCC Part 15 Subpart B, ANSI C63.4-2014

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) This device

must accept any interference received, including interference that may cause undesirable

operation.

DATE OF ISSUE: April 27, 2022

Sharper Image Dual Jet Spa User manual

Sharper Image Dual Jet Spa User manual

Sharper Image Dual Jet Spa User manual

Related papers

Other documents